Question about 1993 Chevrolet S-10 Blazer

Open Question

How to change front and rear turn signal bulbs on a 1993 chevy blazer S10

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jimbopickens
  • 56 Answers

SOURCE: 98 chevy s10 blazer turn signal

Unplug the turn signal relay from the fuse box and start you engine. Does it still make that noise?
If yes... Put the relay back in, that is not the problem.
If No...Then the relay could be bad, replace it!

PLEASE RATE THIS SOLUTION! Thank You Very Much!

Posted on Nov 25, 2008

CRTN
  • 716 Answers

SOURCE: rear turn signal bulb on a 2001 Chevy Monte Carlo

Its Accessed Through The Trunk Pop It And There Will Be Either A Panel To Remove Or Carpeting Material To Move Aside And You'll See The Wiring Harness With The Light Twist And Pull To Get The Bulb You Want Out.

Posted on Jan 16, 2009

  • 82 Answers

SOURCE: 1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks

have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Posted on Mar 11, 2009

kidspeedy
  • 321 Answers

SOURCE: left rear turn signal light on my 1999 chev. s10 is not working

any increase in bink speed is direcly related to a bulb being burt out.

Posted on Jun 12, 2009

  • 3741 Answers

SOURCE: Where is the turn signal relay on a chevy s10

On 95-97 and 1998, both the turn signal and hazard flashers are located behind the lower dashboard trim just to the left of the cigarette lighter. You can not get to it without taking apart the trim (stupid design). Or you have to drill a 2" diameter hole in the trim with a velcro cover so you would never have to do it again1999 and later it is under the glove compartment
to disassemble it without drilling
It's behind the panel to the left of the cigarrette lighter. You need a Torx 25 screwdriver and another screwdriver for those hex shaped screws, forgot the size. First unscrew the 2 Torx 25 screws beneath the steering wheel. Then unscrew the rest of those Hex screws on the bottom. The panels overlap, so be prepared for a lot of unscrewing. You do need to unscrew the middle black panel on the bottom, right beneath the cig lighter. It's held by two Hex shaped screws, one on each side and are hard to unscrew. Also you need to remove your spare change sliding tray to unscrew the last hex looking screw. Once you pop your panel off, the turn signal flasher is the right one. The Hazard flasher is the left one. You can find a replacement part at Autozone, and DON'T get the $184 Flasher switch, all you need is the signal flasher. It's shaped like a cylinder with TWO prongs on it.

Posted on Nov 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 chevy S10 4x4 passenger rear turn signal and break light not working


I would try measuring for 12 volts at the socket while the turn signal is on.

May 11, 2017 | 1998 Chevrolet S-10 Pickup

1 Answer

Why do the Turn signals on my 95 chevy blazer cause rear brake and turn signals to flash like emergency flashers. Front turn signals operate normally.


Check you ground (negative) connections. A loose or bad ground can result in one bulb finding a ground through another route, which can be another bulb. generally, the bulbs will not be at full brightness if this is the case.

Jan 15, 2015 | Cars & Trucks

1 Answer

What would make my 2003 Chevy S10 pick up not start after only changing the left rear bulb for the blinker ?


Yes but does the turn signal work now? I imagine they are separate problems and you are unlucky, unless the battery is weak or you are out of gas. 25321215-zwfykd1k4rtzjgfuoehmn00z-4-0.jpg

Dec 14, 2014 | Cars & Trucks

2 Answers

My left brake light/turn signal isn't working! I replaced the bulbs and turn signal flasher! Still not working! Its 2000 Chevy s10 blazer


If the other brake and turn lights are working the brake light and flasher units are ok . With a test light check at the bulb holder terminal and bulb holder body, test light should glow ,if not check from terminal to a metal part of panel away from the light body . If test light now glows the brake light body has a bad earth if the test still not glowing the power cable to the light is broken.

May 20, 2014 | Cars & Trucks

1 Answer

Can you take the left front signal cover off on a 1997 chevy blazer to change the signal bulb


No. Unfortunately you have to remove the whole headlight assembly. There are two long screws holding it in. You access them from under the hood. Once they are removed you will be able to get the headlight assembly out and be able to get to the turn signal bulb.

Dec 10, 2010 | 1997 Chevrolet Blazer

3 Answers

1992 chevy s10 no brake lights or turn signals


Check the front and rear (although probably the rear) turn signal bulb socket for corrosion and/or water intrusion. If you find corrosion attempt to clean (but you will probably have to replace the socket and bulb). For water intrusion you will probably have to replace the break lamp assembly.

Aug 02, 2009 | 1992 Chevrolet S-10

2 Answers

How does the rear turn signal lens, L side, come off (to replace bulb) on a 2002 S10 pick up? Thanks in advance. LHH


Hi there,

You open the hood and you will see two small rods with rubber tips on the bar that your hood latches to. Those two rubber tipped things are in fact a morbid attempt at making a funny sort of screw. If you turn these counters clock-wise, the entire headlight assembly will come off and you can change the blinker lights.
You will need a 6mm socket to do it. I recommend that you first spray down along the bolt with some WD40 or other type of lubricant and be careful not to apply too much torque.

Good Luck!!
Thanks

Jul 07, 2009 | 1993 Chevrolet S-10 Blazer

1 Answer

1993 chevy blazer S10


That is a very common problem with General Motors 700R4 transmission. There is a shell that encases the majority of the forward gears and the reverse drum is on top of it and that completely encases the forward drum. at the bottom of that shell there is a collar that is about one quarter of an inch long that rides on a gear set called planetarys. those have a problem with breaking and cause no reverse and driving in neutral. that is the link between the front and rear shaft of the transmission and the weak link. for that to be repaired it has to be removed from the truck and taken apart. It is highly recommended that it be completly rebuilt not just patched due to all of the metal that is sent through the transmission.

Sep 13, 2008 | 1993 Chevrolet S-10 Blazer

Not finding what you are looking for?
1993 Chevrolet S-10 Blazer Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...