Question about 2002 Kia Sedona

1 Answer

Wheel bearing hub on a 2002 Kia Sedona will not move freely after installation what could be the problem

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kia Master
  • 1,334 Answers

You may have overtightened the axle nut or if it's a pressed bearing, it did not go in straight.

Posted on Dec 23, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 334 Answers

SOURCE: wheel bearings

the wheel bearin and hub is one . the bearin is press in . some times it just easer to change the hole thing .and you will have to disconect the tierod upper and lower ball joint . i hope this help you

Posted on Apr 05, 2009

defadad
  • 351 Answers

SOURCE: need instruction manual/schematics for replacing 2005 kia rio driver side rear wheel bearing. i've got the wheel/hub/bearing off, not the inside ring to the bearing. i need to know how to replace it .

clean all the grease if there is any out of the hub, turn the hub over and using a drift and hammer strike the shell from the back edge working around the shell as you go, should not take too much to remove it but you will need a bit more than a tap with the hammer.
Hope this has helped you

Posted on May 22, 2009

iambanshee74
  • 3489 Answers

SOURCE: nut Torque Specification Guide 2004 Kia Sedona

Lower ball joints. Tighten the pinch bolts to 69-85 ft. lbs. (93-115 Nm). Outer tie rod ends. Tighten the nuts to 43-58 ft. lbs. (59-78 Nm). Sway bar links. Tighten nuts to 69-85 ft. lbs. (93-115 Nm). Hub retaining nuts. Tighten the hub nuts to 177-199 ft. lbs. (240-270 Nm). Front wheels. Tighten the lug nuts to 65-79 ft. lbs. (88-108 Nm).

Posted on Jan 28, 2010

drsinister69
  • 2317 Answers

SOURCE: can't get the bearing hub out to replace the bearing

You'll need to remove the 2 strut bolts holding the hub to the strut, remove the axle nut. Pull the hub towards you and try taping on the axleshaft to try to push it out. You might try spraying some WD-40 where the axleshaft goes thru the hub.

Posted on May 02, 2010

  • 87 Answers

SOURCE: My 2002 kia sedona is stuck in park. The gear

shifter cable either broke or came disconnected

Posted on Jul 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a trick to installing the bearing front end KIA sportage


Fix It Right! - Front Hub Bearing Replacement - YouTube

? 14:26
https://www.youtube.com/watch?v=l0LCkycUcqM
Sep 7, 2011 - Uploaded by OneSourceAutomotive
Front Hub Bearing Replacement (S1E3) Demonstrated on a 2004Kia Sedona FWD. ... on a front-wheel ...

Kia Sportage wheel bearing replacement - YouTube

? 4:10
https://www.youtube.com/watch?v=wa6NREeozbE
Apr 3, 2014 - Uploaded by Jo Daddy's Garage
I did a quick replacement of a bad rear wheel bearing/hub on aKia ... How to install front struts on a Kia ...

Dec 09, 2015 | Kia Cars & Trucks

1 Answer

How do you replace the rear wheel hub on a 2003 Kia sedona. All I can find is directions on front not back.


Wheel Bearings

Print
Adjustment

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
  3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).
Removal & Installation

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
  3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.
To install:
  1. Pack the wheel bearings with grease for assembly.
  2. Install or connect the following:

    Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel

Apr 03, 2015 | 2003 Kia Sedona

1 Answer

How to replace front wheel bearing on 2003 kia sedona


Disassembly 1. Remove oil seal from front wheel hub. 2. Remove front wheel hub assembly with suitable tool.

bi6c021a.gif 3. Remove retaining ring. note_icon_eng.gif If the bearing inner race remains on wheel hub, grind a section of inner race until approximately 0.020 in (0.5 mm) remains. Remove race with a chisel.

bi6c021b.gif 4. Remove wheel bearing with suitable tool.

bi6c021c.gif note_icon_eng.gif Do not remove dust cover unless necessary. Do not reuse dust cover if removed. 5. Mark relative positions of dust cover and knuckle for proper reassembly. 6. Remove dust cover with a chisel.

ai2a023c.gif note_icon_eng.gif Do not remove wheel hub bolt unless necessary. Do not reuse wheel hub bolt if removed. 7. Remove wheel hub bolt with a press.

bi6c021d.gif Assembly 1. Press in new wheel studs. note_icon_eng.gif Front wheel hub press in either bolt turning or loosening by the torque of 108.5 lb•ft (147 N•m, 15 kg•m) shall not be premissible.

bi6c022a.gif 2. Mark new dust cover to match the removed dust cover. 3. Align mark on new dust cover with knuckle. 4. Install new dust cover with suitable tool.

bi6c022b.gif 5. Install new wheel bearing with suitable tool. 6. Install front wheel hub assembly with suitable tool.

bi6c022c.gif note_icon_eng.gif Use a new oil seal, and apply grease to seal. Install oil seal so that it is flush with knuckle. 7. Install new oil seal with SST(0K993 331 016).

bi6c022d.gif

Jan 12, 2013 | 2003 Kia Sedona

1 Answer

Install bearn for 2002 kia sedona yes


GO TO SEARS N ROEBUCK AUTO ALIGNMENT CHECK IS FREE THEY WILL TELL YOU WHAT PARTS TAKES 30 - 45 MIN.

Sep 17, 2012 | 2002 Kia Spectra

1 Answer

What is the foot pounds for the front wheel bearings on a 1995 chrysler cirrus


Hello, If you Chrysler has replaceable wheel bearings and seal. This is the way it goes---pack the wheel bearing with new grease-install the bearing in the wheel nub--install new back wheel seal--coat the axle shaft with grease lightly, thing coat-----install wheel hub on to axle shaft...be careful here don't damage the rear hub seal------------insert front race washer---install axle shaft nut--tighten nut down wheel nut until it is firm with water pump pliers----spin the hub/with tire mounted.
(the wheel and hub will turn but not freely)----take the pliers and back off the axle nut 1/4 turn----now spin the wheel and axle hub, it should spin freely---now if doesn't spin freely---back off the axle nut about 1/16 or 1/32 (or just a little bit)-----now, spin the wheel and hub and if turn freely------------Now grab the top of the wheel/tire and move it back and forth.-----if there is some movement ---try tighten the axle nut just a little little bit, unit the one can barely feel some little movement in the wheel/tire and hub.-----------Now, spin the wheel/tire and hub and it should also turn freely.

If it does----install new and correct size of cotter pin and bent the ends around the axle nut.----

coat the inside of the hub cup with grease. Now, use an rubber or plastic hammer to install the cup on the wheel/tire hub. You are finished with one wheel bearing maintenance. Now do the other side.



I really don't know if you Chrysler Cirrus has replaceable wheel bearing. All the auto/trucks have replaceable hubs, that means that the replacement is total hub with axle shaft, sealed bearings, and seals. This is bolt to each wheel steering hub. This work to remove these one unit hubs.

Four bolts hold the axle hub to the steering hub. Hear is the problem!! it has rusted to the steering hub. Also, these hubs cost more than replacing bearings, races, seals to cool turn of $180 to $250+ I wish you luck in your replacement of wheel bearing on your Chrysler. GB..stewbison

Sep 24, 2011 | Chrysler Cirrus Cars & Trucks

1 Answer

What is the name of the part the front left bearing goes in a kia sedona 2004


The wheel bearing is pressed into the steering knuckle and the hub is pressed into the wheel bearing. Hope this helps.

Feb 15, 2011 | 2004 Kia Sedona

1 Answer

My 2002 kia sedona is stuck in park. The gear


shifter cable either broke or came disconnected

Jul 23, 2010 | 2002 Kia Sedona

1 Answer

Wheel bearings need replaced, what is the cost?


bearing about £50 plus about 2hrs labour

Feb 11, 2010 | 2002 Kia Sedona

2 Answers

2004 Kias Sedona. I have the replaced the Front Wheel Bearing (Passenger Side) 4 Times in the last 6 months. The last one lasted 2 Days. It was sluggish going uphill, jerking, and then there was a loud...


My guess is the original shim that came with the factory bearing and hub assembly was discarded and never installed on the new bearing (That does not come with a shim) causing the new bearing to fail.

Jan 16, 2010 | 2004 Kia Sedona

1 Answer

Wheel bearings


the wheel bearin and hub is one . the bearin is press in . some times it just easer to change the hole thing .and you will have to disconect the tierod upper and lower ball joint . i hope this help you

Apr 05, 2009 | 2004 Kia Sedona

Not finding what you are looking for?
2002 Kia Sedona Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...