Question about 1988 Chevrolet S-10

1 Answer

I have 1988 Chevy s10 4x4 I keep blowing fuses for my turn right side turn signals and brake lights I unhooked all the wires coming from main harness in back and same problem thinking maybe turn sig

Posted by on

  • Frank Dunlap
    Frank Dunlap Dec 24, 2016

    Should I unhook brake light switch and then try turn signal again maybe it brake light switch shorting out

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 1,334 Answers

May want to also check your wiring from the fuse panel to the different components that are giving you the problem. I think that you may have a pinched wiring along the way to all the components.

Posted on Dec 23, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Right rear brake turn signal chevy 2007 express van wire harness must be bad no power at wire at socket


Have you checked the fuses ? If you got power there, then begin checking wiring for damage, breaks or shorted.

Dec 02, 2016 | Cars & Trucks

1 Answer

Why does my turn signal/ hazard light fuse keep blowing out


you have a short in one of the light sockets or a worn wire from the wiring harness. could be the flasher assembly. are the turn signals different bulbs from the brake lights? Does using the brakes blow the fuse? (Rear lights or brake light switch on brake pedal). left or right turn signal blowing the fuse will tell which side has the short. 4 ways only, replace the relay.

May 21, 2015 | 2004 Jeep Grand Cherokee

1 Answer

1994 dodge dakota brake light ground location


The ground wiring on newer vehicles is a little complicated. Older cars, the ground would have been to the body around the tail-lights, but these have a ground wire in the harness and is connected to the turn-signal switch, and other sources. I don't think you have a ground problem. Does the fuse blow as soon as you press it into the fuse-block, or when you step on the brake? I believe you have a dead short somewhere, possibly a pinched turn-signal wire close to the tail-light assembly. Brake lights work through the turn-signal wires from the turn-signal switch on the steering column. That's how you can have one side blinking for turn while the other side stays on for brake. I'm kind of shooting in the dark here because I don't know what all you've done. If you replaced the turn-signal switch in the steering column, you may have pinched a wire or something there. Another thing, if the fuse doesn't blow as soon as you press it in, will both turn-signals work as long as you don't press on the brake? If you can provide a little more information, I might be able to help you more. One last thing....Have you replaced tail-light/turn-signal bulbs? If so, be sure you used the right bulb. You should only have two bulbs, one for back-up lights and one 1157-type combination for tail-lights and turn-signals. I have seen people use a single contact (1056) bulb in place of a 1157, which creates a short from brake/turn-signal back into the tail-light circuit. I do have a 1994 Dodge Dakota.

Mar 12, 2014 | 1994 Dodge Dakota Club Cab

1 Answer

Brack lights wont light up on my 1988 ford ranger we keep blowing fuse and put in new brake switch


If you keep blowing the brake fuse than you have a short in the system. Unplug the brake switch. Install a new fuse. If it did not blow than the problem is after the brake switch. Next unplug the turn signal switch, then plug the stop light switch back in and press the brake pedal. Did the fuse blow. If not than the wiring is good in between the two switches. With the turn signal switch disconnected use a jumper wire in between the light green wire (power from the brake switch) and the orange with light blue wire (power to the right brake lamp). If the fuse blows than there is a short in the right side brake circuit between the plug in and the rear socket assembly. If the fuse does not blow than jump from the light green wire to the Light green with orange wire (power to the left brake lamp). If the fuse blows than the problem is in the left hand brake wiring circuit.

Sep 04, 2013 | Cars & Trucks

1 Answer

1995 Chevy Caprice Wagon, right side signals and brake lights dont work


change the bulb if still out then check and test socket/ground wiring/wire harness for damage

Apr 28, 2017 | Cars & Trucks

1 Answer

1998 Chevy Silverado 1500 Brake light fuse blew, replaced, fuse blew again, replaced relay and fuses. both under hood and in side fuse panel. Fuses keep blowing on turn signal and brake lights. Checked...


you obviously have a short to ground on one of the wires to the back (if it was the front the brake shouldn't blow the fuse). the most common problem is usually in a trailer light harness. if you look under the drivers side rear of the truck, down under the tail light there will be a plugin junction. pull this plug-in apart and see if the fuse still blows. if it does then the problem is forward of that connector, if it doesn't then the problem is behind that plugin. be sure to check for "green death" (electrical corrosion) at all joints especially any trailer hook ups.

Oct 25, 2012 | 1999 Chevrolet Silverado 1500

3 Answers

2001 Chevy Silverado. When I plug in the trailer


its in the engine compartment in the fuse box on the drivers side next to battery

Oct 07, 2009 | 2001 Chevrolet Silverado

1 Answer

2000 Chevy CK, have hazard lights, turn signals,


test your brake switch located on the brake fulcrum. you can unhook the wires and usea paper clip to connect the two wires together if the brake lights come on then replace the switch, if it does not come on and the bulbs are ok then replace turnsignal switch.

Jul 18, 2009 | 1999 Chevrolet 3500

1 Answer

1995 chevy silverado z71 no power to right tail light


check fuse.if good you got grounding problems or faulty turn signal switch.

May 09, 2009 | 1996 Chevrolet K1500

2 Answers

Brake lights, hazard lights, and the left turn signal do not work on my 1988 Chevy/Grumman step van. I changed the turn signal switch - not the problem; the fuse eventually blows for the stop...


Has this ever had a trailer hitch? If so follow the trailer wiring back to the mess, and the problem ... If not that ... I would check for a pinched harness on or near the steering column ... I would have said the signal switch too. You may have to follow this harness all the way back or foward ... it won't be fun.

Apr 30, 2009 | 1984 Chevrolet Sportvan G30

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...