Question about Ford Cars & Trucks

1 Answer

No brake lights as soon as you push the brake pedal it blows the # 13 fuse which the e flashers,ABS,turn signals and brake lights the battery I just need a wiring diagram for 93 Ford F-350 flat bed

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,373 Answers

Type diagram you want into google and click images may be there worth a look

Posted on Dec 23, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75066 Answers

SOURCE: 1996 honda accord no turn signal

Check the wiring in the front and back to lights for shorts to ground, if nothing is found replace the turn signal switch, be careful to disarm the airbag before doing any work on the column as the steering wheel must be pulled to replace the turn switch.

Posted on Oct 07, 2008

  • 14 Answers

SOURCE: 1988 ford thunderbird brake lights and turn signals not working

When this happens the problem is most likely the multi-funtion switch aka turn signal switch. Check to see if the 3rd brakelight comes on when the brake pedal is pushed. If so replace the MFS. The 3rd brakelight in late 80's fords bypasses the turnsignal switch.

Posted on Dec 29, 2008

  • 5 Answers

SOURCE: Left turn signal stops flashing when brake pedal is depressed.

there is a ground problem, most likely in the tail unit itself, but a ground problem is hard to find and easy to fix. reground the system, the turning unit, and the problem should stop. About the hazards, I don't know...... some times in older cars, that is the way it works. because the brake and hazard element in the bulb is the same and the old cars used a break in the power, but the new cars use a break in the ground. any way, chase the ground down first, it is usually the cause.

Posted on Feb 12, 2009

cabrooksjr
  • 13 Answers

SOURCE: 93 GMC Suburban, No Tail Lights

Check the trailer plug ground first. If in doubt. Ground in another location. Make sure the area is free of rust and the ground is tight.

Posted on Jun 28, 2009

  • 49 Answers

SOURCE: right turn signal stays on will not flash left works.2001 jimmy

its your blinker box.. all major lights run through there

Posted on Aug 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the stop lamp or brake lamp fuse and panel for a 2007 cadillac cts?


Kevin , this is a very complex way of stoplamp control , I will post GM service Description and Operation of how they work an let you deside if you want to tackle this ! Do the center high mount brake lights work ?
The brake pedal position sensor is a resistive device used to sense the action of the driver's application of the brake pedal. The brake pedal position sensor provides an analog signal that will increase as the brake pedal is pressed.
The brake pedal position sensor receives both a 5-volt reference voltage and a low reference signal from the electronic brake control module (EBCM). When the brake pedal is pressed, a variable signal is applied from the brake pedal position sensor to the EBCM through the brake sensor signal circuit. The fuse block left rear supplies battery positive voltage to the bass relay switch through the BASS fuse. One side of the bass relay coil is permanently grounded at G402. The EBCM supplies voltage to the bass relay coil upon receiving the signal from the brake pedal position sensor. The switch contacts of the bas relay close and battery positive voltage is applied through the bas relay switch to the center high mounted stop lamp (CHMSL), and to the turn signal/hazard flasher module through the stop lamp switch signal circuit. The ground for the CHMSL is applied from G402. The turn signal/hazard flasher module then supplies voltage to the left and right stop lamps in the tail lamp assemblies that have ground at G401 and G402. For export vehicles the stop lamps receive battery positive voltage directly from the bass relay.

There could be a code stored in the EBCM - electronic brake control module - DTC B3903 Stop Lamp Relay Circuit
DTC C0278 Brake Pedal Position Sensor Not Calibrated
there are several other codes that pertane to the brake lights . you could try Replaceing the bas relay !
Fuse Block - Left Rear
In the passenger compartment, under the left side of the rear seat at carpet.

Jun 28, 2015 | 2007 Cadillac CTS 3.6L

1 Answer

Why does my turn signal/ hazard light fuse keep blowing out


you have a short in one of the light sockets or a worn wire from the wiring harness. could be the flasher assembly. are the turn signals different bulbs from the brake lights? Does using the brakes blow the fuse? (Rear lights or brake light switch on brake pedal). left or right turn signal blowing the fuse will tell which side has the short. 4 ways only, replace the relay.

May 21, 2015 | 2004 Jeep Grand Cherokee

1 Answer

Brake lights 1990 dodge Dakota don't work is there an in line fuse that I am missing


Check the switch on the brake pedal first, then if you have power to it and power goes out when pedal is pushed you probably have a broken wire under the chasis

Mar 26, 2015 | 1990 Dodge Dakota

3 Answers

1999 ford expedition no brake light no turn signal


Sounds like your multifunction control switch needs replaced. Its location is on your steering colum.

9ad0f03f-26fd-405e-89cb-10b4ae059161.jpg

Feb 14, 2015 | 1999 Ford Expedition

3 Answers

Hi, I have a 2004 Corola and I recently had my flasher fuse replaced 3 times in one day. When I tuen the flasher on it will work fine until I stop and the fuse causes the car to turn off. Do you know


no my answer, dont buy that $500 PCM yet.
the Gauge fuse , see bottom left, above. runs lots of things,
the FSM covers this, fully 100%
it runs the Flasher module, the ECM, the integration module (BCM like) that runs interior lighting and many things off the IM.
if the fuse only blows, while blinking , id inspect all 4 corner lamps
id check the wires there and then replace all 4 lamps. if you
dont know how to bench test a lamp. then just replace them.
Gauge , (funny huh) runs the Alternator, if it shorts, boom the Gauge fuse blows. as you can see finding a short is not easy,
you never said how soon it blows. so,,,,, if quicky, id run it
with no alt connected. rear plug IG Plug pulled. do so for no more
that about 15minutes, the battery will drain fast (no head lights please,or fans for heater, no electrical things on, flashers on for sure.)
see???
there are 30 pages, to see all IG1 power feed wires.
i didnt try to find them all.
but that is my point, if you dont have the book or alldata.com login
then all this is pure wild speculation and guessing.
I did this for a living, so ,know the ropes.
once I have this information, i then use my ammeter to find it.
see a area MASTER here, do that.
Duane
https://www.youtube.com/watch?v=TZrCrBx4uFY

and chris.
https://www.youtube.com/watch?v=n5FJDgcdii8

in your case you know what fuse blows. (stated wrong)
and with that , fact i can attach my ammeter, and the pull
modules to find which one has the active short.
in the case if the blinker module is passing excessive current
I then drop off the lamps loads from the flasher module
if that shows that my short is gone then the lamps are shorted.
i can even measure all 4 lamp wire feed to read this short with my ammeter and my CB.
using this.
http://www.fixkick.com/tools/25100B.jpg

http://www.fixkick.com/tools/25100.jpg
below.
this the red fuse below is GAUGE. the module on the right is the Flasher module.
25319711-3kq0vkr3b25vysxdhfxwpufz-4-0.jpg

Dec 13, 2014 | 2004 Toyota Corolla

1 Answer

1995 GMC Jimmy brake lights not working


Brake lights run through the hazzard switch. There are known problems with this, and the multifunction switch. You may need to buy a new hazzard switch and OR the multifunction switch. Before you do that, check the pigtail that goes into the brake switch up by the fender, make sure it's not shorting out up there. Happened to me!

May 06, 2017 | 1995 GMC Jimmy

1 Answer

Brake lights and turn signal don't work???


turn on the emergency flashers(e-flashers)if they work check the bulbs at the same time.if this is good then check the fuses.you may have a problem with the turn signal flasher needing replacing.this is a different flasher than that of the e-flasher,looks the same but a different flasher.usually located on or around the fuse panel under the dash.the brake light problem could be a misadjusted switch or a bad switch.the switch is at the base of the brake pedal and has two wires to it.one wire will have power all the time and the other wire will only have power on it when the brake pedal is pushed.if not then the switch will need replacing.check for broken wires at the switch as these sometimes break causing a problem.

Feb 08, 2012 | 1996 Pontiac Sunfire

3 Answers

No brake lights when i push the pedal


Its the signal light switch on the lever.
THe signal switch has all connections relating to the brake lights!
solution play around with the lever and see or get someone to see the brake lights work with the brake pedal down.
My car does the same thing! when i move the lever towards activaiting the high beams the brake lights work.
just gently push on the lever to see the lights go on.
you have to replace the switch and requires removing the steering wheel without setting off the airbag.

Mar 28, 2010 | 1994 Oldsmobile Cutlass Supreme

3 Answers

Brake lights not working even though the brake peddle is pushed down The switch still goes in and out. Fuse box has some fuses missing. The fuse box does not have a desription on every plug of what it is...


Here are the numbers on your fuseblock and fuses coresponding to the number that is on your fuse block.
1-20 amp (yellow)
Hazard flasher
2-10 amp (red)
back up lights, A/C clutch cycling Switch
3-30 amp (green)
Power windows
4-30 amp (yellow)
A/C or heater blower motor
5-20 amp (yellow)
Panel Lights, Side marker lights, Park, Taillights, Clock & radio display Intensity, License & panel lights.
#6-10 amp (red)
Stoplight, buzzers, Anti-lock brake module
#7-15 amp (lt. Blue)
Tachometer, horn & Relay
#8-8 amp (yellow)
Power Door locks
#9-10 amp (red)
Radio
#10-10 amp (red)
Rear Wheel Anti-lock module, Turn Signals
#11-20 amp (Yellow)
Windshield wiper & washers
#12-15 amp ( LT. Blue)
Cigarette Lighter
#13-5 amp (tan)
Speed Control, warning buzzers, gauges, indicator lights
#14-5 amp (tan)
Time/delay relay & under-hood light, dome light, power mirrors, readio & clock Memory, Interior lights, reading lights
#15-blank
Not used
#16-4 amp (pink)
Radio Lights & overdrive switch light 1989-91, Cluster lights, Cigarette Lighter light & as tray light, Cluster lights, A/C & heater controls.
#17-relay
Hazard Flasher warning
#18-relay
Relay
#19-Circuit breaker
#20-relay
Turn signal Flasher
#21-buzzer
Warning
#22-Relay
Horn

Aug 04, 2009 | 1991 Dodge Dakota

1 Answer

Brake lights inop,fuses constantly blows


Stop lights are genrally routed through rhe tur signal control, which is the most likely place to have a problem. If the signal control feels unusual. there's that maybe provided you've gone the gambit of checking bulbs, pedal switch, etc. get an automatic fuse from the psrts store and put it in the bad fuse spot. It will go on and off like a flasher untul you locate the short. Get one that is lower than the one that blows to get it flashing faster. Do your turn signals and 4 ways workand see whar the do when you appliy the brake whilr on. Good luck

May 27, 2009 | 1995 Chevrolet G20

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...