Question about Cars & Trucks

Open Question

I turn my vid vision 2 glasses on. And all three lights come on and stay on. Even afte i reset it.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove heated rear-vision mirrors glass only


most mirrors have push pins holding the top of the glass to the movable backing plate and 2 lower tabs that slide into slots first.
gently pry on the top of the glass toward you and the glass should release .then lift up to get the tabs out of the bottom 2 slots.

Mar 29, 2015 | 2008 Jeep Commander 3.7

1 Answer

Reset security code 2003 Chevy impaula


Instructions
    • 1 Attempt to start the car. If it does not start, or dies very quickly after it started, then leave the key in the ignition in the "ON" position and wait 10 minutes. Make sure the security light is flashing. After 10 minutes the security light will stop flashing and either turn off or stay on steadily. When it does, then turn the ignition off, wait 20 seconds and attempt to restart the car.
    • 2 Repeat this procedure three times in quick succession without removing the key from the ignition.
    • 3 Start the car following the third 10-minute waiting period. The car should start and stay on. If it stays running, then the codes have been relearned and the problem is solved. If the car still does not start then you may need to have all or part of the passlock system replaced

Jan 15, 2015 | 2003 Chevrolet Impala

1 Answer

How to get change oil light to go off


Instructions:1) Check the oil. The light is a warning signal that you are low on oil or that the oil is not flowing properly. If the oil level is fine then the issue may be a reset button. Two different methods will allow you to reset the oil light.2) Turn the key to the on position. Do not turn the engine on. Press the accelerator pedal down three times in a five-second period. Turn the engine on. If the oil light goes off you have successfully reset the oil light. If it stays on you need to try the second method.3) Find the fuse box. This should be under the dash in between the steering wheel and the door. Open the fuse box and look for the reset button. Press the button until you hearing a beeping sound. It will beep three times. The oil light should be reset. Turn the engine and see if the oil light goes off. If the oil light stays it still has not been successfully reset.
4) Read the manual. The two methods above are the two most common ways of resetting the oil light. Your car may have additional options to try. If none of the methods resets the oil light then there is a different problem such as a non-functioning oil sensor. At this point you need to see a mechanic.

Parts Of BMW.


May 30, 2012 | 2005 Dodge Magnum

2 Answers

2005 pontiac astek...changed oil and filter but the change oil light still stay's on for 3 minutes ? how do you reset it ?


Turn the key on,push the accelerator three times slowly with in 5 seconds,and this will reset the oil change reminder,if this was helpful,please rate,and thank you.

Jun 21, 2010 | 2001 Pontiac Aztek

4 Answers

Oil light stays on


You need to put the key on and push the gas pedal to the floor three times within five second to reset the oil life light.Some g.m.'s have a reset buttom in the fuse panel that needs to be pushed first and some don't.Check the owners manual under change oil for your specific year car.

Oct 21, 2009 | 2003 Chevrolet Impala

1 Answer

I can't reset the engine oil life in a 2007 H3 it did work in the past, all I can do now is change the language. I called the dealer they are no help at all.


try
Resetting the Change Engine Oil light System
On some vehicles it is possible to reset the Engine Oil life with Tech 2 (in Engine) otherwise the following procedure can be used.
1. Turn the ignition key to the ON position
2. Fully depress and release the accelerator pedal three times within five seconds.
3. The Change Engine Oil light will flash while the system is resetting.
4. When the light stops flashing, turn the key to LOCK/OFF. If the Change Engine Oil light comes back on and stays on when the vehicle is started, the system has not reset. Repeat the Reset procedure.

Jul 07, 2009 | 2001 Hummer H3

1 Answer

1999 GMC Yukon aft door will not lock. I have


Take some sand paper to those brass connection and get a shiny surface this is the most common fault. you didn't mention if the aft door glass has defrosting strips on the glass the possibl 5th pin is for those>

May 11, 2009 | 1999 GMC Yukon

2 Answers

Air bag light is blinking


my airbag light is blinking . can i reset anything its a04 nissaun armada

May 02, 2009 | 2004 Nissan Armada

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...