Question about 2011 Chrysler Town and Country

1 Answer

How do I change the starter on my 2011 Chrysler town and country

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 1,335 Answers

Safety first, so begin by disconnecting the battery. Then lift your vehicle and place on jack stands. Then remove the few main wires that are attached to the starter. Make sure you label or make them so you know where they go once you are ready to hook them back up. Then, remove the bolts that hold it to the transmission. Once removed, reverse the procedure to install. Good luck

Posted on Dec 23, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

garyq1970
  • 73 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

chryslertech
  • 115 Answers

SOURCE: low speed fan relay for the 2005 chrysler town and country

If you are talking about the cooling fan relay for the radiator there is no low speed and high speed relay. There is only one relay and it is behind the grill revitted to the bumper rail. It is doesnt look like you typical relay.

Posted on Mar 08, 2009

c17hydro
  • 2984 Answers

SOURCE: Front PCV Valve on chrysler town and country

1930013.gif
PCV valve location-2.4L engine

3a8cecf.gif
PCV valve location-3.3L and 3.8L engines

Posted on Nov 13, 2009

  • 50 Answers

SOURCE: how to remove starter for 2002 chrysler town &

There are two bolts to remove, opposite sides. One is a normal bolt, the other one is hidden by wires. Remove the nut on the ground wire, remove the ground wire, use deep socket over this to remove the bolt. It's easier than you think, about an hour and a half total.

Posted on Jan 24, 2010

  • 55 Answers

SOURCE: 2002 chrysler town and country starter - won't

front of motor lower end just follow from battery down the wire is red there should be 3 bolts holding it on

Posted on May 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the starter located on a 2011 Chrysler town and country


You have remove Catalytic Converter and Engine mountes to get to the Starter.
This is the procedure

  1. Disconnect and isolate the negative battery cable.
  2. Remove the catalytic converter (3) See: Engine, Cooling and Exhaust\Exhaust System\Catalytic Converter\Service and Repair\Catalytic Converter - Removal.
  3. Remove the front engine mount through bolt.
  4. Remove the retainers (2) from the front engine mount bracket (1) and remove the bracket.
  5. Remove the field generator connector (1).
  6. Remove the B+ retainer (2) and B+ cable (3).
  7. Remove the stater retainers (1).
  8. Remove the starter (2).

Aug 27, 2017 | 2011 Chrysler Town and Country

1 Answer

My 2011 town n country will not even crank it gets juice all rest kites come on but will not crank


The first thing you do is have the battery tested, just because the lights come on doesn't mean the battery can run a starter which takes up to 100 amps. Any Autozone or other chain auto parts store will do the test for free.

Nov 10, 2016 | 2011 Chrysler Town and Country

1 Answer

2004 Chrysler Town and Country won't start. Lights, radio and horn works just fine. Even put in a new starter and still get nothing. Ran a wire from battery to the starter and got a little kick.


Chrysler Town & Country Questions - My van won't start ...

www.cargurus.com > Questions > Chrysler > Town & Country

CarGurusSep 29, 2008 - ckf2004 answered 4 years ago. I have a 96 chrysler town and countrylx and the engine died, turned over but wouldn't start, I researched and replace the flywheel .... My van sometimes won't start because it kills the battery.

My town & country 2004 wont start sometimes - CarGurus

www.cargurus.com > Questions > Chrysler > Town & Country

CarGurusMy town & country 2004 wont start sometimes - My van start doing something really weird. it will ... Asked by TownCountryguy May 03, 2013 at 03:31 PM about the 2004 Chrysler Town & Country Base .... Sometimes you tap it & it won't work.

Van won't start - Chrysler town and country - YouTube

? 1:01
https://www.youtube.com/watch?v=mkEL2vlLZr0
Jun 26, 2014 - Uploaded by Philip Walker
We have the same issue currently...very randomly...with our 2008 Caravan at the moment. Wife just got ...

2011 Chrysler Town & Country Engine Won't Turn Over, Will ...

www.carcomplaints.com/Chrysler/Town_Country/.../engine_wont_turn_...
The 2011 Chrysler Town & Country has 34 complaints for engine won't turn over, will not start. Average repair cost is $902.00 at 58178 miles.

Jan 14, 2016 | Chrysler Cars & Trucks

1 Answer

#1 cylinder is misfiring, put new fuel ejector and the problem is still there.It has a bad noise in the motor.


Thread: Cylinder 1 misfire P0301 - The Chrysler Minivan Fan Club ...

forum.chryslerminivan.net/showthread.../27978-Cylinder-1-misfire-P03...

Feb 6, 2013 - 7 posts - ‎4 authors
My mother-in-law's 2002 Town and Country has the P0301 cylinder 1 misfire error code. I haven't done much work on this type of car, so I'm not ... '05 Town & Country Cylinder 1 misfire mystery
10 posts
Feb 3, 2014
Engine misfire
7 posts
May 6, 2012
#1 Cylinder misfires at idle only
10 posts
Jun 4, 2011
Running rich / Misfire Mystery
10 posts
Sep 20, 2010
More results from forum.chryslerminivan.net

Part 1 -How to Test the Coil Pack (2001-2008 Chrysler 3.3L ...

easyautodiagnostics.com > Chrysler > 3.3L, 3.8L
Apr 29, 2011 - Page 1 of 7: How to Test the Coil Pack (2001-2008 Chrysler 3.3L, 3.8L). ... This article will help you troubleshoot a Misfire Condition that might be setting ...your 2001-2009 Chrysler (or Dodge) 3.3L or 3.8L Town and Country, Voyager, ... it's important the you know what 'Paired Cylinders' and 'Non-Paired ...

Jan 03, 2016 | 2001 Chrysler Town & Country

1 Answer

Need diagram for juntion box


Thread: fuse box?? - The Chrysler Minivan Fan Club Forums

forum.chryslerminivan.net/showthread.php/21174-fuse-box

Jun 26, 2011 - 10 posts - ‎3 authors
Does anyone have a diagram for the fuse box (junction box) that is inside on the drivers side for a 1998 Town and Country. I need to know what the relays are for, my manual only shows the fuses and there is ... Forum · The Minivan Mopar Garage · 3rd Generation Chrysler Minivans: 1996-2000; fuse box?Missing: juntion

Interior Fuse Box Location: 1996-2000 Chrysler Town and ...

www.carcarekiosk.com/video/2000_Chrysler_Town_and.../replace
Interior Fuse Box Location: 1996-2000 Chrysler Town and Country ... box of your 2000Chrysler Town and Country in addition to the fuse panel diagram location. ... If youneed to replace a blown fuse in your Town and Country, make sure you ...Missing: juntion

Dec 21, 2015 | 1996 Chrysler Town & Country

1 Answer

2011 Chrysler town and country belt keeps shedding


Secure the power steering pump. check that all bolts are tight.

Aug 29, 2014 | 2011 Chrysler Town and Country

1 Answer

2011 Town & Country gear selector knob "cap" needs replacing


If it's not on Ebay or Craigslist you best bet is the dealer or if you get lucky try a few salvage yards. That's a dealer part

Jul 25, 2014 | 2011 Chrysler Town and Country

1 Answer

Intermittent wipers do not work on 2011 Chrysler Town & Country


change the switch on the colum this is normal prob in town & country. thay have a lot of electrical issues. typ in your browsee: problems with town and country....you will find hundres of them have electrical issues

Aug 01, 2011 | 2011 Chrysler Town and Country

Not finding what you are looking for?
2011 Chrysler Town and Country Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...