Question about 2004 Hyundai XG350

Open Question

04 xg 350 electrical help

Battery to alternator

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locate the starter


The starter motor will engage the gear in the transmission bell housing to rotate the engine, so it will be mounted on the side of the transmission. The illustration shows the XG-300 and XG-350.


10_1_2011_2_37_23_am.jpg

Sep 30, 2011 | 2004 Hyundai Elantra

1 Answer

2004 hyundai xg 350 l the alarm went off now it wont start


Hello and welcome to FixYa!

As a first course of action, I strongly suggest that you remove the positive battery connector and let is sit for atleast 5mins. then reconnect it again. Reconnecting the positive connector will reset the system and can get your vehicle back to it's normal operation.
Hope this helps and thank you for using FixYa! Have a good one!

Jul 10, 2011 | 2006 Hyundai Santa Fe

1 Answer

ALTERNATOR REPLACEMENT


Assuming this is a XG 350, the process is lengthly.
1. Remove the RH radiator cooling fan (two 10mm bolts at the top & wiring harness connector to it).
2. Lift vehicle to remove the Right Front wheel (then remove 4 10mm bolts securing the plastic splash shield & remove it)
3. Loosen the 14mm nut on the alternator belt tensioner pully
4. Loosen the tension on the belt by rotating (counter-clockwise) the 14mm bolt at the bottom of the idler pully and remove the belt.
5. remove the pully & the idler pully (three 12 mm bolts)
6. Loosen the 14mm nuts at the top and bottom mounting points of the alternator.
7. Using a floor jack (or vehicle lift), support the engine using a jack-stand & 2x4 piece of wood under the oil pan.
8. This is tricky - lift the engine 'SLIGHTLY' to take pressure off the front engine mount - loosen the 17 mm nut on top of the mount itself and observe engine movement. If the engine moves upward 'slightly' remove the 17mm nut - if not, raise the engine slight more until you see the mounting bracket rise off the mount.
9. Remove the remaining 17mm nut (deep well socket), and two 17mm bolts and remove the engine mount bracket.
10. Here's another tricky step. Some 350's bottom Alternator bolt bores are 'SLOTTED'... some are NOT. You'll need to determine wether you'll need to REMOVE the lower bolt, or just loosen the mounting sleeve at the bottom bolt. If it's 'sleeved', I use an air hammer to loosen the sleeve. If it's not slotted, I remove the lower bolt (it's the only way to remove the alternator and pry it off).
11. At the top is an "L" bracket which uses two 12mm bolts to attach it to the engine (head). One of the two 12mm bolts is difficult to get to -- do your best to remove it because the battery cable to the alternator is in the way.
12. Disconnect the alternator wiring (battery cable & regulator harness connector)
13. Lift the engine as high as it will go & pry the alternator off its lower mounting.
14. manuver the alternator upward taking care not to damage the radiator.
15. Installation is in reverse order.
NOTE: If your XG's lower mounting point was slotted, your task is easy. If it isn't, your task now becomes more difficult as you must align the new alternator to facillitate re-insertion of the lower bolt.
PS If not slotted, I use a telliscoping magnet to help re-insert the lower bolt.

Aug 09, 2010 | 2004 Hyundai XG350

1 Answer

Where is my starter and how do I change my starter?


2000 Hyundai Elantra 2.0L MFI DOHC 4cylRemoval & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Speedometer and shift control cables Starter electrical connectors Starter motor
  3. 2e15922.jpg

    Fig. Exploded view of the starter-XG 300 and XG 350

To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 25 ft. lbs. (34 Nm) Starter electrical connectors Speedometer and shift control cables Negative battery cable
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Air intake assembly Speedometer cable Shift cable Starter wiring connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 20-25 ft. lbs. (26-33 Nm) Starter wiring connectors and torque the battery cable nut to 88-140 inch lbs. (10-16 Nm) Shift cable Speedometer cable Air intake assembly Negative battery cable
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Air intake assembly Speedometer cable Shift cable Starter wiring connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 20-25 ft. lbs. (26-33 Nm) Starter wiring connectors and torque the battery cable nut to 88-140 inch lbs. (10-16 Nm) Shift cable Speedometer cable Air intake assembly Negative battery cable
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Speedometer and shift control cables Starter electrical connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 25 ft. lbs. (34 Nm) Starter electrical connectors Speedometer and shift control cables Negative battery cable.

All Others
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable and wait at least 3 minutes Speedometer cable and shift cable from the transaxle Starter motor wiring Starter motor bolts and the starter
To install:
  1. Installation is the reverse of removal. Tighten motor retainers to 20-25 ft. lbs. (27-34 Nm).

Hope helps (remember rated this).

Jul 14, 2010 | 2000 Hyundai Elantra

1 Answer

How do I replace the alternator in a 2002 hyundai sonata GLS v6?


For 2002 Hyundai Sonata 2.7L MFI DOHC 6cyl check this procedure...
Alternator - Removal
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Radiator mounting bolts, 1.6L only Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator

    0e1822c.jpg
    Fig. Exploded view of the alternator-XG 300
Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Radiator mounting bolts, 1.6L only Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator
  3. Install or connect the following:
    Alternator and reposition the radiator, if raised Alternator wiring harness connectors Alternator drive belt
  4. Adjust the alternator belt and torque the bolts to the following specifications:
    1. Accent: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 14-20 ft. lbs. (19-28 Nm).
    2. 2.0L and 2.5L Sonata, Elantra and Tiburon: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 105-132 inch lbs. (12-15 Nm).
    3. 2.4L Sonata: Pivot bolt to 26-41 ft. lbs. (34-54 Nm) and the adjustment bolt to 14-18 ft. lbs. (19-25 Nm).
    4. 3.0L Sonata and XG 300: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 11-16 ft. lbs. (15-22 Nm).
  5. Install the radiator mounting bolts, if removed.
  6. Connect the negative battery cable.

Hope helps (remember rated this).

Jun 25, 2010 | Hyundai Motor 2002 Sonata

1 Answer

I need to know how to replace a water pump on a 2002 hyundai gx 350.


2002 Hyundai XG350 3.5L MFI DOHC 6cylWater Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Accessory drive belts Water pump pulley Timing belt, tensioner and idler pulley Water pump

  4. 1514f36.jpg

    Fig. Water pump assembly-XG 300 and XG 350 (click over pic for zoom)

To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.
To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.

95486b3.jpg


Fig. Water pump bolt lengths-3.5L engine

Install the water pump with new gaskets and O-rings. Tighten the bolts to the following specifications:
  1. 1.5L SOHC engine: 105-132 inch lbs. (12-15 Nm).
  2. 1.5L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  3. 1.6L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  4. 1.8L, 2.0L, and 2.4L engines: 14-20 ft. lbs. (20-27 Nm).
  5. 2.5L engine: 11-16 ft. lbs. (15-22 Nm).

Hope helps (remember rated this).

Jun 18, 2010 | 2002 Hyundai XG350

2 Answers

2004 hyundai XG-350 Check engine light is on and


Sorry Peter I do not have a solution to your car problem, but I also own a 2004 XG-350 and the SAME EXACT thing is happening to my car right now, crazy huh. Pretty much started out of nowhere...the boyfriend is going to go try the leaving keys in ON position and reconnecting the battery. Did you happen to find out what was wrong with yours, thought maybe if you did it would help save me a step. Praying nothing to serious. Hope you got your car working well again!

Thanks,
Nikki

May 14, 2010 | 2004 Hyundai XG350

1 Answer

Need to remove the alternator on a 96 E-350


FIRST TURN OFF RADIO.SO YOU WONT LOSE CODE.DISCONNECT NEGATIVE BATTERY CABLE.DISCONNECT THE ELECTRICAL CONNECTORS FROM THE ALTERNATOR.REMOVE THE ALTERNATOR DRIVE BELT.THEN REMOVE THE PIVOT BOLT AND ADJUSTING BOLT OR THE MOUNTING BOLTS.THEN REMOVE THE ALTERNATOR FROM THE ENGINE.REMOVE THE ALTERNATOR FAN SHIELD IF EQUIPPED.

Oct 03, 2009 | Ford E-350 Cars & Trucks

1 Answer

The abs light came on and air conditioner started blowing hot. After work the batt was dead. Jumped it and guages were dead for about 30 sec. About 10 miles later abs light went off and air got cold again....


It sounds like the engine is running on battery power only.The engine of today`s technology needs the alternator to have enough ignition to run on,lights and computer,etc,will be affected by low voltage,and amps.The alternator is not charging,look for a charging fuse to see if it is blown.If the fuse is fine,replace the alternator,and have the battery recharged on a slow 2 amp charge so it will recover it`s loss of deep cycle amps.This will prolong battery life and alternator.If I can help let me know.Let me know the out come.

Aug 29, 2009 | 2004 Ford F350

3 Answers

How do I remove the alternator from a 2002 V6 Hyundai Sonata once I have disconnected the alternator?


Removal
  1. Remove or disconnect the following:

    Negative battery cable Radiator mounting bolts, 1.6L only Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator

0f18cd4.gif


Fig. Exploded view of the alternator-XG 300 and XG 350


Removal & Installation
  1. Remove or disconnect the following:
    Negative battery cable Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator 5ead6d5.gif


  2. Fig. Exploded view of the alternator-XG 300 and XG 350

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Negative battery cable Radiator mounting bolts, 1.6L only Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator

    27b2f58.gif

    Fig. Exploded view of the alternator-XG 300


    0900c15280196f8f.jpg
    Fig. Exploded view of the alternator-XG 350

  3. Install or connect the following:

    Alternator and reposition the radiator, if raised Alternator wiring harness connectors Alternator drive belt
  4. Adjust the alternator belt and torque the bolts to the following specifications:
    1. Accent: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 14-20 ft. lbs. (19-28 Nm).
    2. 2.0L and 2.5L Sonata, Elantra and Tiburon: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 105-132 inch lbs. (12-15 Nm).
    3. 2.4L Sonata: Pivot bolt to 26-41 ft. lbs. (34-54 Nm) and the adjustment bolt to 14-18 ft. lbs. (19-25 Nm).
    4. 3.0L Sonata and XG 300: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 11-16 ft. lbs. (15-22 Nm).
  5. Install the radiator mounting bolts, if removed.
  6. Connect the negative battery cable.


I hope hrlp you with this. Good luck and remember rated this help-


Aug 25, 2009 | Hyundai Sonata Cars & Trucks

Not finding what you are looking for?
2004 Hyundai XG350 Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...