Question about GMC Cars & Trucks

Open Question

2009 GMC Acadia SLT 3.4 I need torque sequence for intake manifold

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76109 Answers

SOURCE: 2009 GMC Acadia SLT 3.6 need intake manifold torque specs and sequence

OK now that you have your engine right does this look right. The numbers are small but they are there. please rate my help.
26410006-a1cgzsxklslsegh3wnnktrhl-1-0.gif

Posted on Dec 23, 2016

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 GMC Acadia SLT 3.6 need intake manifold torque specs and sequence


OK now that you have your engine right does this look right. The numbers are small but they are there. please rate my help.
26410006-a1cgzsxklslsegh3wnnktrhl-1-0.gif

Dec 22, 2016 | GMC Cars & Trucks

1 Answer

2009 gmc acadia replace rear brakes


this is on a bigger truck but its the same procedure for changing your brakes if you dont have a piston tool you can use a c-clamp with an old pad to depress piston (s)back or most auto stores will let you borrow tools
Yahoo Web Search

Aug 07, 2015 | 2009 GMC Acadia SLT-1

1 Answer

Is the mirror housing motor and seat heater on drivers side of 2009 Acadia SLT hooked to same fuse???


Try to go to a near by autoparts store and have them test your fuses, it's free. They can also do a lot more. Good luck

Jul 02, 2015 | 2009 GMC Acadia SLT-2

1 Answer

My 12 volt outlets in gmc acadia not working..where is the fuse for this?


The Fuse block is on the Passenger side right below the glovebox. Look directly below it there is a panel that pulls down.

Jul 17, 2014 | 2009 GMC Acadia SLT-1

1 Answer

Bolt torque sequence on 1991 jaguar xj6 4.0 intake manifold?


intake manifold or head gasket? i know head gasket need a sequential order followed by how many degrees and Lbs of pressure. if its on the intake i doubt it needs an specific torque. just try not to crack the intake manifold since its made of plastic.

Oct 29, 2012 | 1991 Jaguar XJ6

1 Answer

How to replace Acadia A/C Evaporator


You will need to have a factory service manual to do this, no way around this if you want to do it in less than a week. You need to remove the entire dash and cut open the heater box, it is a real pita. You can download one here. Are you sure the evaporator is the cause, make sure of this because it is a part that rarely fails. I have done 3 in 35 years

Oct 01, 2012 | 2009 GMC Acadia SLT-1

1 Answer

Toquer on the intake


start in the center working in an expanding square pattern crossing over the manifold on the first 2 bolts. tighten in 3 steps. these are low torque fasteners, don't over tighten & use locktite.
If reusing the fasteners, apply threadlock GM P/N 12345382 or equivalent to the threads of the lower intake manifold bolts.
Install the lower intake manifold bolts.

Notice: Proper lower intake manifold fastener tightening sequence and torque is critical. Always follow the tightening sequence, and torque the intake manifold bolts using the 3 step method. Failing to do so may distort the crankshaft bearing bore alignment and cause damage to the crankshaft bearings.

Tighten the lower intake manifold bolts.

from front of engine tighten 2 bolt back left side, then 3rd bolt back right side, then 3 bolt back left side, then 2nd bolt back right side, then back bolt left side, back bolt right side, then front bolt left side, then front bolt right side

Tighten the bolts on the first pass in sequence (1-8) to 3 N·m (27 lb in).
Tighten the bolts on the second pass in sequence (1-8) to 12 N·m (106 lb in).
Tighten the bolts on the final pass in sequence (1-8) to 15 N·m (11 lb ft).

Jan 15, 2011 | 1996 Chevrolet Blazer

2 Answers

Need torque specs for a 2001 jeep cherokee intake manifold


Intake manifold using new gaskets. Torque the bolts, in sequence, to 105 inch lbs. (12 Nm)...

6a7ecad.jpg

Fig. Intake manifold torque sequence-3.7 & 4.7L engines


Hope this help (remember comment and rated this).

May 07, 2010 | 2001 Jeep Cherokee

3 Answers

Need head bolt, intake manifold, and exhaust torque specs


Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

Mar 06, 2010 | GMC Suburban Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...