Question about Kia Sephia

1 Answer

How do you adjusting neutral safety switch 2001 kia sophia

I have the neutral safety switch install but it is cranking in reverse. I need to adjust it to crank in park.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Kia Master
  • 75,005 Answers

Move the switch adjustment until it starts in the correct gear setting, it takes 2 people to accomplish this.

Posted on Dec 22, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

We're is the parking reverse neautral circuit on a montero xls 2001 4x4


Hi .

If its the PNP switch that you are looking for this is on the side of your transmission
62e79521-1c6f-49ac-b2bc-50b047114bae.png

Jun 03, 2014 | 2001 Mitsubishi Montero

1 Answer

My 2001 Jeep Grand Cherokee wont start sometimes, but if I put it in neutral then try to start it..It starts .. What is the problem with my baby.......


Test/Service/Replace

The circuit on newer cars with automatic transmissions has a neutral safety, or neutral start switch installed between the ignition switch and the starter. The ignition switch cannot operate the starter motor unless the transmission is in park or neutral.
Late model vehicles with manual transmissions have a starter/clutch interlock switch that requires the clutch to be depressed to the floor.
Neutral Safety Switch
Normal operations of a neutral safety switch provides a quick check for the adjustment of the gear selector linkage.
  • To do this, move the selector slowly until it clicks into the PARK position.
  • Turn the ignition key to the START position.
  • If the starter operates, the PARK position is correct.
  • After checking the PARK position, move the lever slowly toward the NEUTRAL position until the lever drops at the end of the NEUTRAL stop in the selector gate.
  • If the starter also operates at this point, the gearshift linkage is properly adjusted.
  • This quick test also tests the adjustment of the neutral safety switch.
  • If the engine does not start in either or both of these positions, the neutral safety switch or the gear selector linkage needs adjustment or repair.

CAUTION
Since you must work under the vehicle to adjust most shift linkages make sure you properly raise and support the vehicle before working under it. Also, wear safety glasses or goggles while working under the vehicle.
A voltmeter can be used to check the switch for voltage when the ignition key is turned to the START position with the shift lever in PARK or NEUTRAL. If there is no voltage, the switch should be adjusted or replaced.

Jan 26, 2013 | 2002 Jeep Grand Cherokee

1 Answer

2003dodge caravan neutral safty switch


Test/Service/Replace Neutral Safety Switch
Most neutral safety switches are combinations of a neutral safety switch and a backup lamp switch. Others have separate units for these two distinct functions. When the reverse light switch is not part of the neutral safety switch, it seldom needs adjustment, as it is directly activated by the transmission or the gear selector linkage.
f_ttat_t3.20.jpg Typical location of a neutral safety switch on a transaxle. Reprinted with permission of Ford Motor Company. A neutral safety switch allows current to pass from the starter switch to the starter when the lever is placed in the P or N position. Some neutral safety switches are nonadjustable. If these prevent starting in the P or N position and the gear selector linkage is correctly adjusted, they should be replaced.
To adjust a typical neutral safety switch:
  • Place the shift lever in neutral.
  • Loosen the attaching bolts for the switch.
  • Using the angling pin, move the switch until the pin falls into the hole in its rotor.
  • Tighten the attaching bolts.
  • Recheck the switch for continuity. If no voltage is present, replace the switch.
  • The switch sometimes controls the operation of the back-up lights also. With the engine off and the key on, put the selector in reverse position. Check the back-up lights to see that they are on. Then, check in the drive position to see that they are out.

Aug 15, 2012 | Cars & Trucks

1 Answer

Where is neutral switch on a 92 dodge caravan


Safety Switch Most neutral safety switches are combinations of a neutral safety switch and a backup lamp switch. Others have separate units for these two distinct functions. When the reverse light switch is not part of the neutral safety switch, it seldom needs adjustment, as it is directly activated by the transmission or the gear selector linkage.
f_ttat_t3.20.jpg Typical location of a neutral safety switch on a transaxle. Reprinted with permission of Ford Motor Company. A neutral safety switch allows current to pass from the starter switch to the starter when the lever is placed in the P or N position. Some neutral safety switches are nonadjustable. If these prevent starting in the P or N position and the gear selector linkage is correctly adjusted, they should be replaced.
To adjust a typical neutral safety switch:
  • Place the shift lever in neutral.
  • Loosen the attaching bolts for the switch.
  • Using the angling pin, move the switch until the pin falls into the hole in its rotor.
  • Tighten the attaching bolts.
  • Recheck the switch for continuity. If no voltage is present, replace the switch.
  • The switch sometimes controls the operation of the back-up lights also. With the engine off and the key on, put the selector in reverse position. Check the back-up lights to see that they are on. Then, check in the drive position to see that they are out.

May 10, 2012 | 1992 Dodge Caravan

2 Answers

In order to start my 2001 dodge stratus i need to put in reverse then park to start it whats wrong??


sounds like the park neutral switch on the shifter is out of adjustment.

Mar 13, 2011 | 2001 Dodge Stratus

2 Answers

My 2001 f150 4x4 will not start unless i hole the gear shift up while in park. what is the cause of this??


You probably need a linkage adjustment,a neutral safety switch adjustment or replacement of the neutral safety switch.

Mar 06, 2011 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Car will not crank in park it will crank in neutreal


Sounds like neutral safety switch/reverse light switch is not adjusted correctly or needs to be replaced.

Sep 24, 2010 | 1994 Lincoln Town Car

1 Answer

Why wont the car start unless the car is put into reverse?


It sounds like your neutral safety switch on the transmission is bad or needs adjusted.

Jun 14, 2010 | 2002 Kia Spectra

2 Answers

Looking for the neutral safety switch


Neutral Safety/Back-up Light Switch

This is a combination switch which controls both Neutral Safety and Back-up lamp circuits.

C6 Transmission


8290dff.jpg

C6 neutral start switch
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Remove the downshift linkage rod return spring at the low-reverse servo cover.
  4. Coat the outer lever attaching nut with penetrating oil. Remove the nut and lever.
  5. Remove the 2 switch attaching bolts, disconnect the wiring at the connectors and remove the switch.
  6. Installation is the reverse of removal. Adjust the switch and tighten the bolts to 55-75 inch lbs. (6.2-8.5 Nm).
  7. Remove the jackstands and lower the vehicle.
  8. Connect the negative battery cable.
AOD Transmission

e7f4231.jpg

Removing the AOD neutral start switch
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disconnect the wiring from the switch.
  4. Using a deep socket, unscrew the switch.
  5. Installation is the reverse of removal. Tighten the switch to 10 ft. lbs. (14 Nm).
  6. Remove the jackstands and lower the vehicle.
  7. Connect the negative battery cable.
4R70W Transmission

2f68dfc.jpg


Removing the Manual Lever Position (MLP) sensor

As of 1994, the neutral safety switch is referred to as a Manual Lever Position Sensor (MLP).
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disengage the harness connector from the MLP sensor.
  4. Remove the 2 sensor attaching bolts and remove the sensor.
To install:
  1. Install the MLP sensor and install retaining bolts. Do not tighten, the sensor requires adjustment.
  2. Adjust the MLP sensor then tighten attaching screws to 80-100 inch lbs. (9-11 Nm).
  3. Remove the jackstands and lower the vehicle.
  4. Connect the negative battery cable.


ADJUSTMENT

C6 Transmission
  1. Hold the steering column transmission selector lever against the Neutral stop.
  2. Move the sliding block assembly on the neutral switch to the Neutral position and insert a 0.091 in. (2.3mm) gauge pin in the alignment hole on the terminal side of the switch.
  3. Move the switch assembly housing so that the sliding block contacts the actuating pin lever. Secure the switch to the outer tube of the steering column and remove the gauge pin.
  4. Check the operation of the switch. The engine should only start in Neutral and Park .

4R70W Transmission


4cc4151.jpg


Adjusting the MLP sensor

Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.
  1. Position the manual control lever in Neutral .
  2. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
  3. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
  4. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).

I hope help you. Good luck (rated this help).

Sep 17, 2009 | Ford E-250 Cars & Trucks

3 Answers

What is the location of the neutral safety switch on a 2001 Saab 9.3 convertible. Is it a difficult repair with the right tools.


I'm not sure what you mean by "neutral safety switch". I have the shop manual for this car (I also have a 2001) and there is nothing listed under "neutral" or "safety" or "switch" in the index that looks like it.

Jul 19, 2008 | 2001 Saab 9-3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...