Question about Cars & Trucks

Open Question

Manufacture date on 12 gauge double barrel shotgun

Has 3 sets of barrels different length and choke

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75797 Answers

SOURCE: Carb

When you set the choke there are many adjustments, most require linkage rod binding and a choke angle guage, also there is a cold high idle setting when the choke is on, all of these adjustments are different for each carburetor number, the carb number is stamped on the carb, there are 20 or so numbers of carbs for your truck they are called calibrations, My suggestion to you is to get the number off your carb and buy a rebuild kit made by Jiffy, they are the best and provide detailed instructions for each carb number covered by the kit.

Posted on Oct 19, 2008

  • 64 Answers

SOURCE: jump start an 1991 audi

connect a 30 amp wire to the starter terminal on the ignition switch and put a switch in the dash with a live to it. to start the car put the ignition on and put the switch on, the car should start

Posted on Feb 18, 2009

  • 1 Answer

SOURCE: all gauges o.k. but engine won't turn over

did you try tapping the stater lightly while someone turns it over ,if that works then the piston inside the starter is stickin, if not take thae starer out anyways and clean all electrical connections i just had that prob 3 days ago starts fine ,if that doesnt work then time for a new one

Posted on Mar 22, 2009

  • 447 Answers

SOURCE: I have a double barrel J Stevens and arms 12 gauge

If your local gun dealer can't help you, try a gun club.

Posted on Jun 18, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need vaccum diagram for chevy impala 1978 with 6 in line motor with 1 barrel carb. rochester mono jet


To the intake manifold , from your choke, choke close incoming air is restricted, adjustment of the choke via thermostatic spring coil or electric heating element, loosen the 3 screws , as spring heats up the choke gradually opens, hope this helps

Dec 31, 2016 | Cars & Trucks

1 Answer

How do i replace the firing pin spring in my 12 gauge that is at least 100 years old?


I had an antique Knickerbocker double barrel and I took it to a gun smith and he made me a spring. Worked good when I sold it.

Dec 04, 2014 | Cars & Trucks

2 Answers

Why four barrels do not open 65 4100 carb


The choke linkage is not properly hooked up or adjusted. The throttle linkage is not adjusted properly or there isn't enough vacuum. The choke linkage has a tab that prevents the 4 barrels from opening when the choke is engaged. There is a tab on the throttle linkage from the front 2 barrels that will engage the secondaries when they rotate past a certain point. Vacuum opens the top plates on the secondaries.

Sep 19, 2014 | 1965 Ford Mustang

1 Answer

I need manual for a verona 12 gauge shotgun model# sx405sw


WRITE manufacture they supply these manuals for free. Local gun stores can give you this information.

Nov 09, 2013 | Cars & Trucks

1 Answer

Wenchester 1300 pump shoot one time then jams


This is the cars and trucks section, but I will try to help. Make sure your barrel is fully turned into the receiver. Check for cleaning pads jammed into a moving part. Make sure your shell length is correct for the gun.

Try different Factory ammo, reloads may be deformed. Bring some of its' used casings along to a Gunsmith, he/she may be able to look at them and see machine marks from how the firing chamber is operating.

I hope my solution is helpful, please rate.

Nov 06, 2012 | Cars & Trucks

1 Answer

I WANT TO CHANGE THE KEY BARRELS OF MY 1996 ESCORT MK6 18 DESIEL. IF POSSIBLE I DO NOT WANT TO USE FORD'S KEY BARRELS BECAUSE THEY WEAR ALOT. CAN I FIT ANOTHER BRAND THAT ARE MORE DURABLE?


There are a couple different brand names of aftermarket key lock cylinders. LOCKSMART has one for auto transmission and for manual transmission. Part Number LC65620 For the auto, Part Number LC65580 for manual. These are available through Autozone and O'Reilly's. BORG WARNER has makes these also The part numbers are the same. (These are avilable through O'Reilly's and Advance Auto. It may be helpful to let you know that these are probably all manufactured by the same manufacturer that makes the MOTORCRAFT (Ford) cylinders. They just sell to different distributors, who put their names on them.

Note that these are the part numbers for the key and tumbler assembly only. The complete ignition switch assembly ( tumbler, barrel, switch ) is also available through these same suppliers.

Feb 03, 2011 | 1998 Ford Escort

2 Answers

Carb


its better to have it rebuilt......... it might be a float issue do u have black smoke when it first starts????

Oct 19, 2008 | 1981 Ford F 150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...