Question about Cars & Trucks

Open Question

My remote won't stop flashing it flashes fast

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Security light stays on (constant) while truck is in use, no obvious problems though. What is going on


when you lock your vehicle with the remote it engages the alarm and the red light will flash fast for about 15 seconds. Then it will start flashing very slowly to show the system is armed. To disarm it you need to open the door with the remote or put the fob in the ignition. If you use the key to open the door and alarm is on it will go off. Only way I know of to make it quit honking and flashing lights is to hit unlock button or insert for into ignition.
I would sit in the vehicle and arm the lock with the remote and watch to light for about 1 minute to see if it does flash fast first then slowly. If it does it is working fine. If it doesn't then take it in and have dealer look at it.

Dec 07, 2015 | 2010 Dodge Ram Pickup 1500

1 Answer

Security sys light keeps flashing fast


your alarm system needs to be reset, it is indicating that the alarm had been set off by flashing fast...

Jan 15, 2013 | 2008 Chrysler Sebring Convertible

1 Answer

Signals won't work in front


do the backs flash fast? replace front bulbs......

Jul 14, 2012 | Cars & Trucks

1 Answer

2009 ford f-150 4x4 left turn signal flashes too fast


I fixed it. I have had the same problem. The Right rear blinker would not flash. All the other lights did flash. It was intermittent at first, would stop working for a few days, then go a month without any problems. It finally stopped working at all, just the right rear indicator flash. I pulled off taillight assembly, pulled bulb and socket plugs... all looked good.. but it still did not work. Went to auto part store with assembly off and wires tucked in to the frame. Bought bulbs and replaced them.. it still did not work. THEN.... The clerk had me pull the Top socket out and put it in the bottom wire position . Presto!! it worked.. I put the bottom socket in to the top wire position and all is good. Why it worked?? do not know. However if it goes out again I will be buying new socket assemblies. Hope this info helps.

Jan 14, 2012 | 2009 Ford F-150

1 Answer

Secureilock error code 13 on 2007 ford expedition. I am having problems remote starting my expedition.


Securilock problem for your remote start? Check when you try to start it, if the security light is flashing fast it is probably the PATS (security system) bypass. To reprogram it you will need two keys. First insert the first one and turn it to the run position. When the security light shuts off insert the second key and turn it to run. Once the light has gone off the second time pull the key out and hit the start button on the remote start fob, this all has to be done in 10 seconds. The vehicle will start, shut it off and try it again. If it doesn't start look to see if the security light is flashing fast again if it is the bypass needs to be replaced. If the light isn't flashing fast and it still doesn't start it should be honking at you or flashing its lights, count these then look in your manual it will tell you what is wrong. If none of these work let me know and I will help you. You can also check out my profile I have a tip that is about remote starts.

Good Luck

Dec 26, 2010 | 2007 Ford Expedition EL XLT

2 Answers

Turn signals flashing too fast


Yes, This is easy. Recall on this problem. Take into dealer for free recall solution and it will stop.

Jun 24, 2009 | 1999 Buick Regal

2 Answers

Program garage door opener.


press the two outside buttons at the same time. Hold while message reads "clearing codes"
Once you get a cleared message. hold the button that you want to program as your remote and press it down. The light will flash slowly. Take your remote in your other hand and hold it about 3 inches from your review mirror as close to the windsheild as possible. You must do this as soon as you press your designated button on the panel. Hold until your green light starts flashing fast. Once it flashes fast it means you have programmed your button properly.

Suggestions - do not do this in front of your garage as you remote will make you door go up and down the whole time. Also - make sure your batteries are new in your remote so you get a good signal to your button. Last thing - if one remote does not work after a couple of tries - use another remote.

Mar 25, 2009 | 2005 Cadillac Escalade

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...