Question about 2004 Chevrolet Malibu

1 Answer

2004 malibu blinkers dont blink. Manually you can turn off/on. Push flasher and all blinkers come on but dont blink. Please help, Tom

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 3,662 Answers

Common cause of such problems is the hazard light switch which is mostly little-used leaving the contacts dirty and oxidised.
Operating the switch rapidly for a few minutes often restores normal operation of the flashers.

Posted on Dec 22, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 jeep wrangler 2.5


dont break the brakes..... TURNS & HAZ
many blinker, modules , internally flash with any load.
1: check all fuses first... (SOP)
2: then remove the blinker loads from the timer.

see it here
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

see WIRING, (end)
8w-51/52
chapter 8w, page 51-4 shows the switch. (complex it is)
note how brake and turns are shared, resources. (blub elements)
now 8w-52-6
see the flasher module.
see C305 pin 2, any load on that pin will cause it to flash.(inside)
that would be any switch in the combo switch stuck on.

Apr 07, 2014 | 1997 Jeep Tj

1 Answer

We hav blinker problams with my 2004 malibu we


your car has a bad hazard 4-way switch
remove the dash bezzle around the switch
plug the new one in
should fix your turn signals and 4-way flashers

Jul 22, 2010 | 2004 Chevrolet Malibu

2 Answers

Help I don't know how to change a fuse for my blinkers..


Flasher you should find an round flasher in your fuse box. btn-view-details.png --> Application:
With 2 terminals
Notes: ( Autozone has this part # LL552)
Electronic
-->

Jun 04, 2010 | 1987 Jeep Cherokee

1 Answer

The driver side blinker will come on but it will not blink how can i fix this?


If you mean the left turn signal indicator on the dashboard won't blink...sometimes means the actual bulb for your left blinker is out. If you mean the actual exterior blinker bulbs don't blink...may be the flasher.

Apr 03, 2010 | 2005 Chevrolet Malibu

4 Answers

Turn signal or emergency flashers wont work. parts store says they cant find a flasher for them. I checked the turn signal fuse and its good. Any ideas?


The flasher is located above the fuse panel. The relays are built into the switch itself. They have a recall on the 4 way flasher switch because it is faulty and causes blinkers not to turn on. Very common Malibu and other Gm problem

Nov 20, 2009 | 2002 Chevrolet Malibu

1 Answer

The front right turn signal on my 2004 Malibu Maxx will not blink


try changing the peanut bulb underneath the main flasher as they should alternate when one is on the other is off & so on..

Sep 10, 2009 | 2005 Chevrolet Malibu Maxx

1 Answer

TURN SIGNAL, BRAKE & HAZARD LIGHTS


No Turn Signal Operation (blinker)The turn signal lights in your car are a basic electrical system that controls the front and rear blinker lights to alert the intended direction of the vehicle. We have listed some of the most common problems and repair troubleshooting tips below:
Troubleshooting Procedure
To start troubleshooting this problem:
  • Turn the key to the on position (do not start engine)
  • Inspect the system fuse located in the fuse panel and replace if needed. If you cannot find the location of the blinker fuse consult your owner's manual or an online repair manual
  • When a blinker flasher fails it can cause blinker lights to say on, not blink, or not go on at all. To test the blinker system flasher, remove the flasher unit and insert a jumper wire between the two terminals. If blinker stays on in both directions without blinking, replace the flasher. If you cannot find the location of the blinker flasher consult your owners manual or an online repair manual.
  • 1b7f814.jpg

Jul 09, 2009 | 1999 GMC Denali

1 Answer

2004 Cherolet Malibu turn signals work sometimes


the switch in the column has dirt in it or is coming apart most likely.always replace bulbs and flasher(s)
first ,then column switch before spending any money on signal diagnosis. for 15$for bulbs,flasher,20-40$switch,you 90%would have solved problem. gino r.

Mar 22, 2009 | 2004 Chevrolet Malibu

1 Answer

Blinkers / flasher problems


If you got an owners manual it should tell you in there the location of the flasher. if no manual it should around where the fuse box is.

Feb 13, 2009 | 1991 Oldsmobile Toronado

Not finding what you are looking for?
2004 Chevrolet Malibu Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...