Question about Cars & Trucks

Open Question

Where is the oil pressure sending unit on a 2004 Vulcan Taurus engine?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
dgjtex
  • 405 Answers

SOURCE: The oil gauge in my

have you changed the oil sending unit, this is the most probable cause.

Posted on Jan 07, 2009

Ad
roedmondson
  • 68 Answers

SOURCE: Where is the oil pressure sending unit on 2004 Dodge stratus

Most likely the oil pressure switch may be damaged. This is a simple procedure. Change and observe the results

Posted on Jan 23, 2009

farroutideas
  • 78 Answers

SOURCE: oil pressure sending unit

Hi there;

Your looking foer the oil pressure sensor on the 2004 8.1L.
You will find it located directly behind the EGR valve threaded into the block just to the drivers side of the center bolt for the transmission to block connection.

Thanks
Farrout!

Posted on Mar 17, 2009

  • 1 Answer

SOURCE: where is the oil pressure sending unit on 2004 dodge stratus?

per the Haynes manual for the 95-05 Dodge Stratus on the 2.0L & 2.4L DOHC 4 cyl engines, the oil pressure sending unit is located at the left end of the rear side of the block. On 2.4L SOHC 4 cyl engines, the sending unit is located at the left end of the rear side of the block. On 2.5L & 3.0L V6 engines, the sending unit is located on the oil filter housing, on the front side of the block. On 2.7L V6 engines, the sending unit is located at the left end of the rear side of the block. To access it, remove the heat shield.

Posted on Dec 23, 2009

ZJLimited
  • 17970 Answers

SOURCE: where is the oil sending unit on a 1996 ford

On 3.0L OHV engines, the oil pressure sensor is located on the left side of the engine block above the flywheel. On 3.0L DOHC engines the sensor is located on the left side of the engine block above the oil filter. On 3.4L DOHC engines the sensor is screwed into the oil filter adapter. The oil pressure sensor operates the oil pressure warning lamp.

71f6e37.jpg
Fig. 1: Location of the oil pressure sensor-3.0L OHV engines


046f42b.jpg Fig. 2: Location of the oil pressure sensor-3.0L DOHC engines

69cce3e.jpg

Fig. 3. The oil pressure sensor-3.0L OHV engine

Hope help with this (remember rated this help). Good luck.

Posted on Feb 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Lwhere is oil pressure sending unit on 2006 dakota v6 located?


Location of the OPS unit is at the rear of engine near the distributor. (OPS) oil pressure sending

Jul 11, 2014 | 2004 Dodge Stratus

1 Answer

Low oil pressure light on not low on oil


sending unit might be bad but purchase a oil pressure tester and put where u take out the sending unit and youll know

Jul 21, 2012 | 2004 Ford Taurus

1 Answer

Where is the oil sending unit on a 1996 ford taurus 3.0 liter engine located? glenn


On 3.0L OHV engines, the oil pressure sensor is located on the left side of the engine block above the flywheel. On 3.0L DOHC engines the sensor is located on the left side of the engine block above the oil filter. On 3.4L DOHC engines the sensor is screwed into the oil filter adapter. The oil pressure sensor operates the oil pressure warning lamp.

71f6e37.jpg
Fig. 1: Location of the oil pressure sensor-3.0L OHV engines


046f42b.jpg Fig. 2: Location of the oil pressure sensor-3.0L DOHC engines

69cce3e.jpg

Fig. 3. The oil pressure sensor-3.0L OHV engine

Hope help with this (remember rated this help). Good luck.

Feb 18, 2010 | 1996 Ford Taurus

2 Answers

What causes the oil pressure gauge to fluctuate on my 2004 Jeep Grand Cherokee Laredo?


If the oil pressure is good and there is no engine noises then the oil pressure sending unit is the problem.Just replace it and you should be good.Hope this helps.Good luck.

Jan 07, 2010 | 2004 Jeep Grand Cherokee

2 Answers

Exact location of oil sending unit on a 95 ford taurus 3.8 v6?


on OHV engine,at rear of engine block,just ahead of transaxle
on OHC on forward side above oil filter.

Oct 16, 2009 | 1995 Ford Taurus

1 Answer

Wheres the oil pressure sending unit located on a 95 3.8 v6 taurus?


Oil pressure switch is on the lower left front of engine. Low oil level switch is on the lower center of the engine.

Sep 10, 2009 | 1995 Ford Taurus

1 Answer

Where is the oil pressure sending unit on 2004 Dodge stratus


Most likely the oil pressure switch may be damaged. This is a simple procedure. Change and observe the results

Jan 23, 2009 | 2004 Dodge Stratus

5 Answers

Where is the oil pressure sending unit on 2004 dodge stratus?


per the Haynes manual for the 95-05 Dodge Stratus on the 2.0L & 2.4L DOHC 4 cyl engines, the oil pressure sending unit is located at the left end of the rear side of the block. On 2.4L SOHC 4 cyl engines, the sending unit is located at the left end of the rear side of the block. On 2.5L & 3.0L V6 engines, the sending unit is located on the oil filter housing, on the front side of the block. On 2.7L V6 engines, the sending unit is located at the left end of the rear side of the block. To access it, remove the heat shield.

Jan 23, 2009 | 2004 Dodge Stratus

1 Answer

Oil light stays on 3.0 no lubrication to upper heads


Try pulling the electrical connector for the oil pressure sensor first. Examine the connections on both the connector and the sensor terminals and clean up both any dirt, grease, or corrossion. Reattach the connector and check the oil light again. If it is still lighting up, replace the sensor/sending unit.

If your engine is the OHV Vulcan engine, the oil pressure sensor/sending unit is at the rear of the block, just ahead of the transaxle. If you have the OHC engine, the sensor/sending unit is on front side of the block above the oil filter.

Why do you note "no lubrication in upper heads"? How would you know that? Next step if sensor replacement does not help, is running the OBDII Diagnostics and checking the trouble codes, if any.

Oct 03, 2008 | 1996 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...