Question about 2011 Dodge Nitro

1 Answer

How do I get in the new lug studs from here 2011 dodge nitro the gap is too small for me to get them in at an angle

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 1,921 Answers

Remove the brake shoes. If there is still not enough room, you may have to remove the axle.

Posted on Dec 23, 2016

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bunnydawg
  • 5158 Answers

SOURCE: 1990 Sentra How it remove and replace lug studs on front wheel

there is a large nut that holds that hub on. Remove the cotter pin and the cap from the bolt... remove the bolt and the hub comes off.

Robert

Posted on Feb 27, 2009

  • 3640 Answers

SOURCE: broken lug nut how to replace lug nut studs

take off tire. remove old stud by hammering it out with a punch. put a socket behind axle plate so as not to break the plate. when replacing, just start stud from back by hand, then use a lug nut to pull it in tight. when tight replace tire!

Posted on Apr 14, 2010

  • 365 Answers

SOURCE: How do I replace a broken lug nut stud on a 08

not sure about your car but most other cars you just hit the old stud with a sledge hammer from the outside which will force the stud out the back of the axle, the studs are on a spline which stops them from turning when you tighten the wheel nuts.
when you replace the damaged stud with the new one you just push it in from the back locating the spline slightly, place the nut on the stud and tighten it, this will pull the stud into place
hope this helps

Posted on Jul 11, 2010

emissionwiz
  • 75030 Answers

SOURCE: jeep broken lug nut stud

Causes are the mounting surface of the the rotor or drum not clean when wheel was installed, wheel bent, suspension damaged, wheels not torques down correctly or left loose.

Posted on Apr 09, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the new lug studs in on a 2011 nitro the gap is too small for me to get them in do I need to do something


Front Tire, brake caliper n brakes, disk brake rotor, behind the disk on hub if 4x4 or spindles if 2x4..
12_22_2016_4_34_21_am.jpg

Dec 22, 2016 | Cars & Trucks

2 Answers

How to change front axle studs


U hammer them out and then use a new nut and a sleeve (a short piece of pipe works) to pull them back into the serrated opening. Use lube on the nut and sleeve when pulling the new studs in place.

Sep 21, 2016 | 2000 Dodge Dakota Quad Cab

1 Answer

How to replace front wheel studs on 2011 Kia Forte


If you can find just the studs and not have to buy the whole hub assembly, screw a lug nut on flush to the stud and drive it out with a hammer, make sure its in a position to have room on the back side. Put in new stud and with a few spacers tighten a lug nut to seat it.

Aug 15, 2014 | Cars & Trucks

1 Answer

Dodge nitro


ok code po455 is a code for the evaporative control monitor,for this i would suggest you check the dealer because its a very large leak in the evap system,and for the po456 which is a very small leak in the evap system

Jul 15, 2014 | 2011 Dodge Nitro

1 Answer

What would cause the engine light to come on Dodge Nitro 2011?


What codes do you have?

Why would start installing parts,
until you diagnose the codes &
actually find a problem?

May 22, 2014 | 2011 Dodge Nitro Shock

1 Answer

How do I replace a broken lug nut stud on a 08 Dodge Nitro


not sure about your car but most other cars you just hit the old stud with a sledge hammer from the outside which will force the stud out the back of the axle, the studs are on a spline which stops them from turning when you tighten the wheel nuts.
when you replace the damaged stud with the new one you just push it in from the back locating the spline slightly, place the nut on the stud and tighten it, this will pull the stud into place
hope this helps

Jul 11, 2010 | 2008 Dodge Nitro

2 Answers

Broken lug stud on rear of 2001 Dodge Dakota


knock it out and draw in a new one wihtt the lug nut and some spacers.

Sep 23, 2009 | 2001 Dodge Dakota

2 Answers

How to replace rear wheel stud. 2003 dodge caravan


Should be a pressed in wheel stud, remove hub and have old one pressed out or you can do it the primitive way, by double nutting the old stud and striking it with a hammer to pound it out, if threads are bad then just strike the stud by itself , then replace new stud in opposite fashion...

Sep 15, 2009 | 2003 Dodge Caravan

Not finding what you are looking for?
2011 Dodge Nitro Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...