Question about Cars & Trucks

Open Question

Install new batteries - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a battery in a Saturn ion 2003?


1. Open the trunk

2. Lift the carpet/flooring of the trunk to reveal the battery.

3. Disconnect the negative battery cable (8mm)

4. Disconnect the positive battery cable (8mm).

5. Remove the battery hold down block (13mm).

6. Remove the battery vent tubes from the top of the battery.

7. Lift the battery out of the trunk.

8. Install the new battery in the trunk.

9. Install the hold down block.

10. Install the battery vent tubes.

11. Install the positive cable.

12. Install the negative cable.

13. Lay the flooring/carpet back down where it fits correctly.

14. Close the trunk.

Feb 25, 2015 | Saturn Ion Cars & Trucks

1 Answer

How to change powerstering pump chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Dec 13, 2012 | 2008 Chevrolet Uplander

2 Answers

Replace power steering pump on 06 chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Jul 08, 2012 | 2006 Chevrolet Uplander

1 Answer

I want to know how to install a battery on my 2007 hyndai tucson


its very easy there is a black cover on the battery that sometimes wont fit the new battery don't worry about it there is a bolt holding down the battery to the tray 2 cables and it lifts up and out put the new battery in bolt it down install both cables and you're done

Jul 26, 2010 | 2007 Hyundai Tucson Limited

1 Answer

Need to change the battery in a 2003 Chevy Impala. How do I do this? take out and replace? thank you.


Yes you simply take the old one out and install the new one. Or you can, drive to your local Advance Auto Parts and purchase a new battery. They will remove the old battery and install the new one free of charge. Other Auto Parts Stores may do the same.

Jun 01, 2010 | 2003 Chevrolet Impala

1 Answer

99 ford contour hazard flasher unit where is it


Flashers - REPLACEMENT

Turn Signal Flasher
(see Figure 1)

e21631a.jpg

Fig. 1: The turn signal flasher is located on the multi-function switch in the steering column
  1. Disconnect the negative battery cable.
  2. Remove the upper and lower steering column shrouds.
  3. Pull the flasher from the back of the multi-function switch.

To install:
  1. Install a new flasher in the multi-function switch.
  2. Install the column shrouds.
  3. Connect the negative battery cable.

Hazard Warning Flasher
  1. Disconnect the negative battery cable.
  2. Remove the knee bolster panel from the underside of the driver's side of the instrument panel.
  3. Grasp and pull the flasher from the connector located near the top of the steering column.

To install:
  1. Install a new flasher in the connector.
  2. Install the knee bolster panel.
  3. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Apr 02, 2010 | Ford Contour Cars & Trucks

1 Answer

All gauges went dead while driving, lights progressively dimmed and finally engine quit.


Your alternator died. You drove until your battery died also. You need a new alternator and a new battery. You might be able to get away with just charging your battery. Do Not jump start the vehicle and let the new alternator try to charge the old battery! Take the battery to a service station for testing and a charge. Install the new alternator and then install the charged battery not vice versa and you'll be fine.

Feb 20, 2010 | 1999 Honda Odyssey

2 Answers

How to switch out the battery


Remove Negative terminal first, then positive terminal. Battery will have some type of tie down or block at base with a bolt you will have to remove. Remember how it goes back together. Remove battery.
Install new battery and tie down or block. Install Positive terminal then Negative terminal.
Remember to never touch both Positive and negative terminals with a metal object (ie..ratchet, wrench etc) this can cause injury and/or permanent damage to a new battery.

Nov 27, 2009 | 1995 Eagle Vision

1 Answer

How to replace key door openere battery The remote door lock device reqires a new battery. How do I replace it?


there is a little screw in back ,remove then install a coin or small screw driver in the middle and snap on unit, remove battery keep in mind which way battery sit in at, then install new one, and put back together,no programing needed should work if a battery is the problem good luck, hope this helps.

Oct 12, 2009 | 2007 Saturn Aura XR Sedan

2 Answers

Alternator problem


1.You need to install a Fully charged battery, before you install a new alternator. Otherwise it will burn the alternator up.

2.I read what you typed about installing a new battery. Was the new battery fully charged, and was it installed before the new alternator?
No?
See number 1 above.

Sep 03, 2009 | 2004 Mazda 6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...