Question about Fiat Palio

Open Question

Confirm the timing marks for the Fait palio el 1600 twin cam

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: head bolt torque specs and timing marcs for a 94 volvo 960 6cyl

you do 14 foot pounds then 45 foot pounds then a 120 degree turn.if aluminum heads are what you have

Posted on Nov 18, 2008

Ad
  • 12 Answers

SOURCE: Correct way to align timing marks

hi -- the timing marks on a twin cam are tricky!! heres how- turn the motor over to tdc on the bottom pulley,this will align two marks on the lower cog-----now on the top cog,it has an obvious mark near the teeth-- well disregard this for now!! the cog has a hole in it,in one of the spokes,well this goes at 12 o,clock and lines up with a mark you will see on the housing! now if you are right you will see the mark near the teeth is at around 4,oclock---i just did one and it is right--cheers

Posted on May 28, 2009

stevenhurc
  • 450 Answers

SOURCE: Looking for cambelt timing marks/ positions please, Twin cam engine Thanks Kevin

these bend valves if belt breaks while running
Align the timing marks on the camshaft gears to the notches on the camshaft cover, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
Align the mark on the crankshaft gear with the
notch at the bottom of the rear timing belt cover.

Posted on Jun 29, 2009

  • 1757 Answers

SOURCE: timing marks on twin overhead cams 2.4 and crank mark.

Click on the following direct, Free Link. It has several Diagrams including the Timing Belt + Marks for your 2004 Hyundai Sonata 2.4L DOHC In-Line 4-Cylinder Engine (located on the bottom half of the Page on the Link). There are additional Diagrams that will prove to be helpful while you are doing this...

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2004/make/hyundai/model/sonata/2004_hyundai_sonata_timing_belt_diagram_marks.htm

Posted on Apr 16, 2010

Testimonial: "tHANKS, tHIS WILL DO THE JOB."

duane_wong
  • 6826 Answers

SOURCE: How do i reset the

2.3L and 2.4L Engines Before attempting to remove the timing chain, read the entire procedure.

  1. Disconnect the negative battery cable.
  2. Remove the timing chain front cover, as outlined earlier in this section.
  3. Rotate the crankshaft clockwise, as viewed from the front of engine/normal rotation, until the camshaft sprocket timing dowel pin holes line up with the holes in the timing chain housing. The crankshaft sprocket keyway should point upwards and line up with the centerline of the cylinder bores. This is the "timed'' position. Fig. 8: The chain must be in the "timed'' position - 2.3L and 2.4L engines 87953108.gif
    Fig. 9: Remove the timing chain guides 87953109.gif

  4. Remove the timing chain guides.
  5. Raise and safely support the vehicle.
  6. Make sure all of the slack in the timing chain is above the tensioner assembly, then remove the tensioner. The timing chain must be disengaged from any wear grooves in the tensioner shoe in order to remove the shoe. Slide a suitable prytool under the timing chain while pulling the shoe outward. WARNING
    Do NOT attempt to pry the socket off the camshaft or damage to the sprocket or chain housing could occur.
  7. If difficulty is encountered in removing the chain tensioner shoe, remove the intake camshaft sprocket, as follows;
    1. Carefully lower the vehicle.
    2. Hold the intake camshaft sprocket with a suitable tool and remove the sprocket bolt and washer.
    3. Remove the washer from the bolt and rethread the bolt back into the camshaft by hand. The bolt provides a surface to push against.
    4. Remove the camshaft sprocket using a three-jaw puller in the three relief holes in the sprocket.
  8. Unfasten the tensioner assembly retaining bolts, then remove the tensioner. NOTE: The timing chain and crankshaft sprocket MUST be marked before removal. If the chain or sprocket is installed with the wear pattern in the opposite direction, noise and increased wear may occur.
  9. Mark the crankshaft sprocket and timing chain outer surface for reassembly, then remove the chain.
  10. Clean the old sealant off the bolt with a wire brush. Clean the threaded hole in the camshaft with a round nylon brush. Inspect the parts for wear and replace as necessary. Note that some scoring of the chain shoe and guides is normal. To install: WARNING
    Failure to follow this procedure may result in severe engine damage.
  11. Position the intake camshaft sprocket onto the camshaft with the surface marked during removal showing.
  12. Install the intake camshaft sprocket retaining bolt and washer, tighten to 52 ft. lbs. (70 Nm) while holding the sprocket with a suitable tool. Use GM sealant 12345493 or equivalent on the camshaft sprocket bolt.
  13. Place GM tool J 36008, or equivalent camshaft aligning pins, through the holes in the camshaft sprockets into the holes in the timing chain housing. This positions the cams for correct timing.
  14. If the camshafts are out of position and must be rotated more than 1?8 turn in order to install the alignment dowel pins, proceed as follows:
    1. The crankshaft MUST be rotate 90┬░clockwise off of TDC in order to five the valves adequate clearance to open.
    2. Once the camshafts are in position and the dowels installed, rotate the crankshaft counter clockwise back to TDC. WARNING
      Do not rotate the crankshaft clockwise to TDC; valve or piston damage could result. NOTE: The side of the timing chain that was marked during removal must be showing when the chain is installed.

  15. Place the timing chain over the exhaust camshaft sprockets, around the idler sprocket and around the camshaft sprocket.
  16. Set the camshafts at the timed position and install the timing chain. Remove the alignment dowel pin from the intake camshaft. Using GM tool J 39579, rotate the intake camshaft sprocket counter clockwise enough to slide the timing chain over the intake camshaft sprocket. Release the camshaft sprocket wrench (J 39579 or equivalent). The length of the chain between the two camshaft sprockets will tighten. If properly timed, the intake camshaft alignment dowel pin should slide in easily. If the dowel pin does not fully index, the camshafts are NOT timed correctly and the procedure must be repeated.
  17. Leave the alignment dowel pins installed. Raise and safely support the vehicle.
  18. With the slack removed from the chain between the intake camshaft sprocket and the crankshaft sprocket, the timing marks on the crankshaft and cylinder block should be aligned. If the marks are not aligned, move the chain one tooth forward or rearward, remove the slack and recheck the marks. Fig. 10: Timing chain assembly retaining bolts - 2.3L and 2.4L engines 87953111.gif

  19. Reload the timing chain tensioner assembly to its "zero'' position as follows:
    1. Form a keeper from a piece of heavy gauge wire, as shown in the accompanying figure.
    2. Apply slight force on the tensioner blade to compress the plunger.
    3. Insert a small prytool into the reset access hole, and pry the ratchet pawl away from the ratchet teeth while forcing the plunger completely in the hole.
    4. Install the keeper between the access hole and the blade. Fig. 11: Reloading the tensioner to its "ZERO'' position, then install to the chain housing 87953110.gif

  20. Install the tensioner assembly to the timing chain housing. Recheck the plunger assembly installation, it is correctly installed when the long end is toward the crankshaft. Install the tensioner retaining bolts; tighten to 89 inch lbs. (10 Nm).
  21. Carefully lower the vehicle enough to reach and remove the alignment dowel pins. WARNING
    Severe engine damage could result if the engine is not properly timed.
  22. Rotate the crankshaft clockwise (normal rotation) two full rotations. Align the crankshaft keyway with the mark on the cylinder block and reinstall the alignment dowel pins. The pins will slide in easily if the engine is correctly timed.
  23. Install the timing chain guides, then install the front (timing chain) cover.
  24. Connect the negative battery cable.
prev.gif next.gif

Posted on Oct 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install timing chain with timing marks both crankshaft and camshaft


Hellen, For the second time, Re POST year, make, model, engine size and complete question so we, here at fixya can answer your question effectively.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Still pulling hair Twin Cam timing marks How accurate Engine Exhaust...
16v fast tbelt swap
Twin cam 16 valve timing marks Google Search

Aug 11, 2016 | Cars & Trucks

1 Answer

I want to know where the timing marks is on the fiat palio weekend 1600 16v


You must have had shop manual to install cylinder head correctly. If not, you need one to get this right. Do it wrong and you will bend valves again, so invest in cheap shop manual.

Jun 27, 2015 | Fiat Cars & Trucks

1 Answer

How do iset the cam timing on a fiat palio 1600 16valve without the locking tool


Although I believe there are timing marks on this engine, the best way to check that the engine is correctly timed is to obtain a tool kit such as the Sealey VS1402. Follow the instructions provided with the kit.

Oct 14, 2014 | Fiat Palio Cars & Trucks

1 Answer

Timing belt snaped on fiat palio 16v how do i find the cam marks


There are special tools you need to lock the cams in the correct position. Without these it is near impossible to get the valve timing 100% right. These locking plates fit on the opposite ends of the cam boxes from the cam gears and belt by removing the blanks on that end.
I managed to borrow a set and set it up correctly. I then made my own marks on the cam gears for future reference.

timing-belt-snaped-fiat-palio-16v-find-qdbodrihfgbojyt0cxubj1mu-3-0.jpg

timing-belt-snaped-fiat-palio-16v-find-qdbodrihfgbojyt0cxubj1mu-3-1.jpg

Apr 09, 2014 | 2005 Fiat Palio Weekend

1 Answer

I need the specs for my cambelt timing i have a fiat palio 1.2 model 2002


fiat punto ,1.2 its a valve free engine so it will not bash the valves ,the bottom pulley mark points at teh top ,you will seea corresponding mark and the cam is top left hand side ,you will see another coresponding mark their for the cam on the ally rocker cover

Mar 30, 2011 | Fiat 500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...