Question about Ford Ranger

1 Answer

Location of vaccum modulator valve on a 99 ford ranger

2 wheel drive with 4 cyl automatic transmission

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 11,447 Answers

There isn't one , transmission is controlled electrically . If it doesn't shift right have it checked for DTC's - diagnostic trouble codes . Does the speedometer work ? VSS - vehicle speed sensor , input speed sensor .

Posted on Dec 21, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Will a 87 ford ranger v6 4 wheel drive trans. fit in a 86 ford ranger 4 cyl 4 wheel drive


If automatic transmission wont work engine block's are not the same, if stander transmission you could swap out bell housing held on with four bolt's from one to the other. Good luck and hope this was very helpful.

May 19, 2010 | 1986 Ford Ranger 2WD

4 Answers

Does the 3.0l transmission fit on the 4.0l engine


Hiya,

There are 5 automatic transmissions used in the Ford Ranger, Explorer and Mountaineer. They may be identified by checking the transmission code on the Safety Standard Certification Label attached to the driver's side door post, in the space marked Trans. The transmissions can also be identified by a tag attached to the lower left hand extension attaching bolt. The transmission codes are as follows:
  • 1991–94 code T is for the A4LD transmission
  • 1995–99 code T is for the 4R44E (2.3L, 2.5L & 3.0L) or 4R55E (4.0L) transmission
  • 1996–99 code U is for the 4R70W (5.0L) transmission
  • 1997–99 code D is for the 5R55E (5-speed automatic) transmission
So, what you need to do now is...establish from a FORD workshop, whether both the A4LD and 4R55E transmissions share the same components and mounting dimensions.

Cheers,

Scott

Nov 12, 2009 | 1992 Ford Ranger

2 Answers

How replace a transmission modulator valve on


It is located on the transmission with a vaccume line going to it. There is a clamp with a bolt that holds it to the transmission. It is an easy fix.

Oct 10, 2009 | 1993 Ford F150 SuperCab

1 Answer

1994 ford ranger 2.8 v6 engine automatic 4 wheel


That could Be caused by the TFI module Located on the side of the distributor its grey module that requires a special tool to remove the two screws

Aug 04, 2009 | 1984 Ford Ranger

1 Answer

Modulator possibly went bad


use a Mityvac or any type of vaccum pump vaccum tester tool (avail at ay parts store) and hook it to the vacuum nipple of the vacuum modulator on the side of the trans, pump the tool to see if modualtor holds vacuum, if it doesn't it is defective.

Jun 19, 2009 | 1990 Ford F250

3 Answers

Transmission Problem in 1991 Ford Aerostar Van.


I dont think so, no. The transmission in the 4.0 L is a standalone tranny made by Ford. I BELIEVE that the 3.0 L engine uses the same transmission that is used in the Ford Ranger.

Feb 04, 2009 | 1991 Ford Aerostar Extended

2 Answers

4 wheel drive


there is a way to do that.....all you have to do is go get the manual locking hubs and switch it over...not that hard....did it to a early 90s f150....pretty easy.

Sep 30, 2008 | 1999 Ford Ranger SuperCab

1 Answer

91 Ford Ranger 4 cyl 5 speed. Can`t find clutch slave cyl. bleeder. Internal slave. Hard at times to get into 1st and rev. Also can`t find connector to hook up tester for check engine light on.


first the bleeder will be located on the cylinder that is mounted on the transmission to engine connection by the bell housing. Second the port for this is located along the drivers side under the hood either by the fire wall or along the top of wheel well it will be marked with a grey cap labled EEC.

Aug 28, 2008 | 1991 Ford Ranger Supercab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...