Question about Cars & Trucks

1 Answer

I10 1.2 kappa engine cemsaft taiming posiosan

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 5,143 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram taiming chainmark vq25 engine


You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..




This is for car and truck problems.

Sep 17, 2012 | Cars & Trucks

1 Answer

Taiming position mazda 626 ex 2.2


Ignition timing for tuneup should be 6 degrees BTDC measured with timing light And engine idling at 600 to 700 RPM, vacuum advance to distributor removed for setting timing. The timing light is set up with the trigger lead connected to the spark plug of cylinder number one which is the first cylinder form the front of the engine.

Be sure to remove the "SPOUT" connector first for an accurate baseline ignition timing. It will be in the vicinity of the ignitionmodule itself, it will hang out from the harness as 2 wires plugged into a small plastic piece. Remove for setting timing and replace when done.

The timing mark on the main pulley should be marked with chalk for visibility, and it should be algined with engine running with the casting behind that front pulley and to the left as you face the front of the engine. at between 6 and 10 degrees Before Top Dead Center. The casting is marked off with the degrees on either side of "TDC" and "before,"

The timing adjustment is made by loosening the clamp bolt that holds the distributor in the engine just enough to allow rotation of the distributor with some effort, but not much. Once timing has been set, retighten clamp bolt.


For cam timing when timing belt is replaced, the engine is rotated so piston on number 1 cylinder is at top dead center, the cam gear has a mark on it's edge for number 1 cylinder that aligns with an alignment mark cast in the head.

Dec 30, 2011 | Ford Escort Cars & Trucks

2 Answers

I am trying to put my taiming chain back on on my 2003 x-type jaguar . how do i kno if its in timing and if i rotated the bottom pulley without one of the timing chains on will it be out of time


basic engine principles apply here ,cam timing marks are located on the end of the cam a notch or a little slot whatever you want to call it that lines up with the cam cap .piston at no1 top then inlet valve closed and been closed a short while and exhaust valve closed but moving around to open ,then look for the marks ,and if the book says no5 halfway up and no2 halfway down ignore it as its no doubt a haynes book and they are written by mechanical engineers not motor vehicle technicians .its only a jag and they are not difficult to repair

Apr 04, 2011 | 2002 Jaguar X-Type

1 Answer

Taiming belt


Welcome to FIxYa.com

What size engine ?

Regards, Lee Davidian


A Four Thumbs up ^^^^ is appreciated for answering your question. And please take the time to rate me by leaving a testimony. Thank you, Lee Davidian

Oct 16, 2010 | 2002 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...