Question about 1999 Nissan Altima

2 Answers

Oil not circulating ? 1999 Nissan Altima DOHC, KA24DE, 200315 miles The right side guide rail to the lower timing chain shattered and jammed the oil pump. I have replaced the oil pump and both timing chain guides. I have removed and cleaned the steel oil pan, the aluminum oil pan (beside the transmission), the valve cover/cams and chains. I have cleaned the drain holes on the driver side of the valves. Also the pickup in the pan, and the everything on the front of the motor. I've changed the oil and filter twice, but the valves are making lots of noise and the oil light comes on. (I also cleaned the sensor for the oil pressure.) There is a hose that runs along the back side of the motor beneath the manifold. Where does this hose connect to the block? Is there another component in the oil circulation that I have missed? Any help will be appreciated!

Posted by on

  • rickcorbitt Jul 21, 2009

    Rottweiler10,

    Thanks for the quick reply. I primed the oil pump several times, as it liked to drain on me while I was mounting it to the engine. The compression pressure averages 138.25 for the four cylinders. (#4 was the weakest at 135.)

    I also removed the oil filter mounting bracket and cleaned it.

    I'm going to try kerosene to loosen anything else ...

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 43 Answers

Well, from the oil pump it goes into your oil filter so the lines going from the pump into the filter could be clogged. check that and see. Also on most imports I have found that they have to be primed after the oil pump has been replaced. Buy a oil pressure gauge and hook it up. Disconnect your fuel and spark delivery and then just crank over your motor to make sure you have good pressure. It takes up to 30 seconds to build on some cars. hope that helps.

Posted on Jul 21, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

When replaceing pump you have two rubber orings one fits into the block the other into the oilpump cover if you overlook or doint replace or replace only one you loose oil pressure at the block.


Posted on Jun 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I NEED TIMING CHAIN DIAGRAM FOR VQ20 NISSAN SERFIRO 1999


Instructions
  1. Remove Your Timing Chain
    • 1 Check your owner's manual for the recommended mileage for replacing your timing chain. Replacement for a Nissan Altima is 60,000 miles.
    • 2 Locate the timing chain. Replace it if the automatic chain adjuster (also known as the tensioner) is damaged or worn.
    • 3 Drain the cooling system and disengage the negative battery cable. Undo the spark plug wires and set the No. 1 piston at "Top Dead Center" (TDC) of the compression stroke.
    • 4 Disconnect the engine undercover, vacuum and fuel hoses, harness and connectors, drive belts, power steering reservoir, alternator and bracket, upper radiator hose, air duct, front exhaust tube, intake manifold collector supports, collector and exhaust manifold and the distributor.
    • 5 Prop up the oil pan and take out the front engine mounting, the valve cover, camshaft sprockets, cam bearing caps, camshafts, cylinder head bolts (reverse the installation order), cam sprocket cover, upper chain tensioner, chain guides and chain, idler sprocket bolt, cylinder head, intake manifold and cylinder head gasket and the steel oil pan.
    • 6 Place a steel cutter between the steel and aluminum oil pans. Slip the cutter around the oil pan's edge. Disengage the steel oil pan, baffle plate, oil strainer and the front tube.
    • 7 Secure the car on jack stands and place a seal cutter in between the oil pan and cylinder block. Slip the cutter around the oil pan's edge.
    Install Your Timing Chain
    • 8 Reconnect the crankshaft sprocket, oil pump drive spacer, idler sprocket and lower timing chain. Position the lower timing chain on the sprockets and line up the mating marks.
    • 9 Rub on an unbroken bead of liquid gasket and put in a new front cover and oil seal. Secure the bolt at 105 to 112 foot pounds (142 to 152 Nm).
    • 10 Eliminate any old material from the pan and cylinder block mounting surfaces. Rub on a 3.5 to 4.5mm bead of liquid gasket over the oil pan and cylinder block.
    • 11 Attach the upper timing chain to the idler sprockets and secure the cylinder head bolts.
    • 12 Refill the cooling system and add clean oil in the engine.
    • 13 Hook up the negative battery cable and any other disconnected parts or items. Start the engine and look for leaks.
Tips & Warnings
  • Procedures for replacing timing chains in Nissan Altimas vary slightly depending on engine size.
  • Make sure the new timing chain matches the chain you are removing.

Jun 12, 2012 | Cars & Trucks

1 Answer

Timing chain 96 maxima broke


Check your owner's manual for the recommended mileage for replacing your timing chain. Replacement for a Nissan Maxima is 60,000 miles.2 Locate the timing chain. Replace it if the automatic chain adjuster (also known as the tensioner) is damaged or worn.3 Release the pressure in the fuel system, drain the cooling system and disengage the negative battery cable. 4 Undo the upper radiator hose, engine drive belts, power steering pulley and pump with bracket, air duct, passenger front wheel and engine side and undercovers, front exhaust pipe, cylinder head front mounting bracket and head cover, rocker cover, distributor and distributor cap and spark plugs.5 Take off the intake manifold support and move the No. 1 piston at "Top Dead Center" (TDC) of the compression stroke.6 Disconnect the cylinder head front cover, water pump pulley, thermostat housing, upper and lower tensioner and slack side timing chain guide, idler sprocket bolt, camshaft sprocket bolts, sprockets, mounting caps and camshafts. 7 Disengage the cylinder head with the manifolds, idler sprocket shaft, upper timing chain, center crossmember, oil pan and strainer assembly, crankshaft pulley, engine front mount and bracket and the front timing cover. Remove the oil seal and unfasten the timing chain cover, idler and crankshaft sprockets and the oil pump drive spacer. 8 Unfasten the timing chain guide. install Your Timing Chain 1 Grease the oil seal lip with engine oil and place it in the front cover. Verify that the No. 1 piston is at "Top Dead Center" (TDC) of the compression stroke. 2 Reconnect the crankshaft sprocket (marks should point toward the engine's front), oil pump drive spacer and timing chain guide and the lower timing chain. Line up all mating marks.3 Hook up the crankshaft sprocket and pulley, lower timing chain, front cover assembly, engine mount and front mounting bracket, oil strainer and pan assembly and center crossmember.4 Reattach the upper timing chain, idler sprocket (to the back side), cylinder head assembly, idler sprocket bolt and exhaust and intake camshafts. Place the intake camshaft knock pin at 9 o'clock and the exhaust pin at noon. Connect the camshaft bearing caps and distributor brackets and secure all mounting bolts.5 Eliminate any old material from the pan and cylinder block mounting surfaces. Rub on a 3.5 to 4.5mm bead of liquid gasket over the oil pan and cylinder block.6 Attach the upper timing chain to the idler sprockets and secure the cylinder head bolts.7 Refill the cooling system. Hook up the negative battery cable and any other disconnected items. Start the engine and look for leaks.

Oct 14, 2011 | 1996 Nissan Maxima

1 Answer

I need the diagram for the spark plug wires from distibuter to plugs on a 95 nissan altima pls help


1995 Nissan Nissan Altima 2.4 liter DOHC L4 (KA24DE)

zjlimited_251.gif

Hope this helps (remember to rate this answer), good luck.

Mar 16, 2011 | Nissan Altima Cars & Trucks

1 Answer

How to replace the timing chain of nissan cefiro v6 2000? its 97 model.


Engine - Timing Chain/Front Cover Revised Procedure
Classification:
EM98-009
Reference:
NTB98-107
Date:
January 15, 1999
GA16DE TIMING CHAIN/FRONT COVER
REVISED SERVICE PROCEDURE
APPLIED ENGINE:
GA16DE
APPLIED MODELS:
1991-94 Sentra (B13) w/GA16DE
1991-93 NX1600 (B13)
1995-99 Sentra (B14) w/GA16DE
1995-98 200SX (B14) w/GA16DE
SERVICE INFORMATION
A revised service procedure for the engine front cover/timing chain has been adopted for the GA16DE. It is no longer recommended to remove the
cylinder head when removing the timing chain/front cover(s). Utilize the following steps when servicing the front cover, timing chain, guides or
tensioner(s)
PARTS INFORMATION
CLAIMS INFORMATION
Please reference the "Revision C" pages of the Nissan "1992-1999 Warranty Flat Rate Information Manual", Section "AG", Op Codes AG12AA,
AG14AA, AG142A, AG143A, AG144A and AG24AA. Also reference Section "CA", Op Codes CA20AA and CA22AA. You will note that the
descriptions and flat rate times applicable to the B13 and B14 vehicles (with GA16DE engines) for these Op Codes have been revised to reflect this
new procedure.
Caution
^ After removing the timing chain, do not turn the crankshaft and camshaft separately or the valves will strike the piston heads.
^ When installing chain tensioners or other sliding parts, lubricate contacting surfaces with new engine oil.
^ Apply new engine oil to bolt threads and seat surfaces when installing the camshaft sprockets and the crankshaft pulley.
^ Do not spill engine coolant on the drive belts.
^ Please refer to the Service Manual for the correct tightening torque.
Removal
1. Set # 1 piston at TDC on its compression stroke.
2. Remove the spark plug wires.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 2
3. Remove the rocker cover (see Figure 1).
4. Remove the coolant reservoir tank with bracket and reposition it for clearance.
5. Support the engine with a suitable jack.
6. Remove cylinder head front mounting bracket.
7. Remove engine front mounting, then the engine front mounting bracket.
8. Remove cylinder head front cover.
9. Remove the upper chain tensioner (see Figure 2).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 3
10. Wipe off the links of the upper timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the cam sprockets and idler sprocket (see Figure 3)
11. Remove the four (4) front cover to cylinder head bolts.
12. Remove side and lower engine compartment splash covers.
13. Remove the accessory drive belts.
14. Remove the crankshaft pulley.
15. Drain coolant by removing the cylinder block drain plug and opening the radiator drain **** (Refer to MA section of the Service Manual).
16. Drain engine oil.
17. Remove intake manifold support of engine front side.
18. Remove power steering pump, pump bracket and tension rod. Position pump aside for clearance.
19. Remove the thermostat housing (See Figure 4).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 4
20. Remove the lower chain tensioner (see Figure 5).
21. Remove the front exhaust tube. Refer to the "FE" section (Exhaust System) of the Service Manual.
22. Remove the front and rear engine gussets (if equipped) on either side of the oil pan.
NOTE:
On A/T models, remove the rear plate cover.
23. Remove the oil pan (see Figure 6).
a. Insert the Tool between the cylinder block and oil pan.
CAUTION:
Be careful not to damage the aluminum mating face. Do not insert a screwdriver, or the oil pan flange will become damaged.
b. Slide the Tool by tapping it on the side of the Tool with a hammer.
24. Remove the A/C compressor and position it aside for clearance.
25. Remove the A/C and alternator bracket with the alternator.
26. Remove the oil pump drive spacer.
CAUTION:
Be careful not to scratch the drive spacer when removing it.
27. Remove the front cover bolts and front cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 5
CAUTION:
One bolt is located on the water pump (see Figure 7).
*1: Located on engine front mounting bracket.
*2: Located on the water pump.
*3: Located on the power steering oil pump adjusting bar.
CAUTION:
Be careful not to tear or damage the cylinder head gasket.
28. Remove the cylinder block to front cover alignment dowels.
CAUTION:
Do not hit the dowels or the cylinder block will crack.
29. Wipe off the links of the lower timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the idler sprocket and crankshaft sprocket (see Figure 8).
Installation
1. Install the crankshaft sprocket, making sure the mating marks face the front of the engine.
2. Install the idler sprocket and lower timing chain using the mating marks and the paint marks made during the removal process.
CAUTION:
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 6
Be careful not to tear or damage the cylinder head gasket.
3. Install the lower chain guides.
4. Front cover installation:
a. Using a scraper or other suitable tool remove all traces of liquid gasket from the cylinder block and front cover mating surfaces.
b. Install new crankshaft seal in front cover.
c. Install new oil passage O-rings and apply a continuous bead of RTV sealant to the front cover (see Figure 1).
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install the front cover to the engine.
CAUTION:
Be careful not to tear or damage the cylinder head gasket or oil seal.
5. Align oil pump drive spacer with the oil pump, and install.
6. Install the oil strainer.
7. Install oil pan, referring to "Installation" in the "OIL PAN" section of the Service Manual.
8. Install upper timing chain and sprockets, using the painted reference marks made during removal.
9. Install upper chain tensioner.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 7
a. Before installing the chain tensioner, insert a suitable pin into the pin hole of the chain tensioner (see Figure 2) to hold the tensioner in.
b. Once the tensioner is installed, remove the pin.
10. Install the lower chain tensioner (See Figure 3).
NOTE:
Make sure the gasket is facing the proper direction before installing the tensioner.
CAUTION:
Now rotate the crankshaft by hand. Check that no binding or interference problems occur when the engine is rotated.
11. Install the thermostat housing.
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the engine front cover and the thermostat housing.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 8
b. Apply a continuous bead of RTV sealant to the housing as shown in Figure 4.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
12. Install camshaft sprocket cover:
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the cylinder head and camshaft sprocket cover.
b. Apply a continuous bead of RTV sealant to the cover as shown in Figure 5.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install camshaft sprocket cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 9
13. Apply RTV sealant to rocker cover gasket (see Figure 6a) and install rocker cover, tightening the bolts as shown in Figure 6b.
14. Install the following parts:
a. Crankshaft pulley.
b. A/C compressor and alternator bracket with alternator.
c. A/C compressor.
d. Power steering oil pump and tension rod.
15. Install front and rear engine gussets (if equipped), and rear cover plate (A/T models).
16. Install front exhaust tube.
17. Install upper right engine bracket and mount.
18. Install coolant reservoir tank.
19. Install alternator, power steering and A/C compressor drive belts.
20. Install engine compartment splash guards.
21. Install vacuum hoses, electrical harnesses and connectors.
22. Install spark plug wires.
23. Refill with coolant. Refer to the "MA" section ("Changing engine coolant, Engine Maintenance") of the Service Manual.
24. Refill with engine oil. Refer to the "MA" section ("Changing engine oil, Engine Maintenance") of the Service Manual.

Jan 15, 2011 | 1997 Nissan 200SX

1 Answer

I need a diagram of a firing oder for a 1993 nissan altima


1993 Nissan Altima
2.4 liter DOHC L4 (KA24DE)93005627.gif

Dec 14, 2010 | 1993 Nissan Altima

1 Answer

At how many miles is the radiator supposed to be flushed? Also, what about the timing belt? I have a 2003 Nissan Altima and don't have the maintenance guide. I have kept the oil and filter changed on a...


2003 Nissan Altima 2.5 S maintenance manual says 60 k miles or 48 months to flush the coolant and replace it. 105 k miles or 84 months replace the timing belt.

Oct 01, 2010 | 2003 Nissan Altima

2 Answers

Does the timing chain and anything to with oil


Yes and no. If the oil pump is going bad the Connecting rods will knock. The Timing chain could be making the sound if the Chain guide came free. My guess is you have a 7 - 70 warranty and they are trying to get out of rebuilding your engine.

Jul 12, 2010 | 2005 Nissan Quest

2 Answers

1999 Nissan Sentra GXE timing belt/chain maintenance


good day Sir, your nissan sentra 1999 gxe have a timing chain this is some tips for your routine maintenance.
Replace engine oil
Replace engine oil filter i


Oct 29, 2009 | 1999 Nissan Sentra

2 Answers

I have 97000 mile on my 05 Nissan Altima 3.5 SER the timing chain is making noise if I went over 7500 mile on synthic oil would that make my timing chain go bad the dealership said that is why it is making...


That's a load of **** they are feeding you.The timing chain tentioner has a fault and not tentioning the chian.I think you have done a good thing keeping it on synthetic oil.That causes less wear on moving parts than other oils.

Jun 11, 2009 | 2005 Nissan Altima

2 Answers

What will my car sound like, if the timing chain needs to be replaced? I have a 1997 Nissan Altima.


there will be a rattle the front of the engine. the end with all your pulleys and belts on. And it will be hard to work out if it's in the engine or the pulleys.

It is a common that a TICKING coming from the front of the engine is the timing chain guide.

This -->LINK<-- will help you alot.

Regards

Philip

Jul 31, 2008 | 2000 Nissan Altima

Not finding what you are looking for?
1999 Nissan Altima Logo

808 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...