Question about 2000 Oldsmobile Silhouette

Open Question

I have a 2000 olds silhouette. Need to know what size socket i need for the hub assembly.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Replacing dashboard lights on an 2000 Oldsmobile Silhouette Van?

the light bulbs are not replacable unless you can solder, you have to replace the complete instrument cluster, get one from a junk yard 100 bucks.

Posted on Sep 25, 2008

  • 112 Answers

SOURCE: Front hub/bearing replacement

You will find that after you remove the hub, you will need to take it to someone with an engineering press to get the old one out and press the new one in.
Good luck

Posted on Jan 30, 2009

  • 83 Answers

SOURCE: Need diagram of firing oreder for a 2000 olds

I can't upload the diagram but the firing order appears to be 1,4,6,3,2,5

Install the spark plug wire(s) (1, 3 and 5) to the engine right side spark plug(s).

Install the spark plug wire(s) to the retaining clips.

Install the spark plug wire(s) (2, 4 and 6) to the engine left side spark plug(s).

Install the spark plug wire(s) to the retaining clips.

You can get a copy of the service manual from Promanuals.net for cheap.

Posted on Sep 26, 2009

  • 14036 Answers

SOURCE: front wheel bearing assembly unit, what tools will

TOOLS YOU NEED IS 35 METRIC SOCKET FOR AXLE NUT.USE 6 POINT SOCKET.DONT USE 12 POINT SOCKET.COULD DAMAGE AXLE BOLT EDGES.MAKING IT HARD TO GET OFF.YOU NEED A TORQUE WRENCH WITH THE RANGE OF 200 FT LBS TORQUE.YOU NEED 1/2 BREAK BAR.AND A HUB PULLER.NOW TO LOOSEN AXLE NUT.BEST TO LEAVE TIRE ON WITH CAR WEIGHT ON GROUND TO LOOSEN THE AXLE.BECAUSE ITS GOT 192 FT LBS TORQUE.HARD TO LOOSEN WITH TIRE OFF.192 FT LBS TORQUE IS WHAT YOU TORQUE IT AT.BESURE TO READ INSTRUCTIONS TO NEW HUB BEARING ASSEMBLY. YOUR AXLE NUT TORQUE WILL BE DIFFERENT IF YOU GET A NEW GREY NUT.BECAUSE NUT STRENGHT WILL BE DIFFERENT.IF YOU GET A BLACK NUT WHICH IS HARDER STEEL TORQUE WILL BE 192 FT LBS.YOU NEED A 13 METRIC SWIVEL SOCKET TO GET HUB BEARING BOLTS OFF THEY WILL BE IMPOSSIBLE TO REACH WITH OUT IT.HUB BEARING BOLTS TORQUE IS 62 FT LBS

Posted on Mar 17, 2010

  • 7353 Answers

SOURCE: I need to replace a coil pack on my 2000 Olds

Rotate the engine? I really dont know what you are talking about. just unbolt it and bolt a new one on, the wires should be marked on the coil.

Posted on Sep 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size socket do i need for the drive axle/hub nut for a 1997 Chevrolet Cavalier?


I think that one is a 32mm...could b wrong tho..
I'd grab my 32 and 36 if I were going to take it off without looking

Sep 02, 2014 | 1997 Chevrolet Cavalier

1 Answer

Im replacing the front hubs on my 2002 jeep liberty, i need to know the exact socket sizes for the three bolts that hold the hub and the nut on the center axle.. ill appreciated.. thank you


The hub/bearing assembly is mounted to the steering knuckle and is retained by three mounting bolts accessible from the back of the steering knuckle. The hub/bearing unit is not serviceable and must be replaced as an assembly if the bearing or the hub is determined to be defective.

May 17, 2011 | 2002 Jeep Liberty

1 Answer

Rear wheel bearing


if its like the 99 winstar:

safely support the van, remove rear wheel, remove brake drum, remove grease cap. remove caged locknut assembly (38mm socket i think.) then pull the hub assembly from the axel. you may need to cut away the inner race if the bearing falls apart. clean axel, apply alittle anti size compound, then push on the new hub assembly. tighten down the hub nut to specifications (should be on the leaflet in the new bearing package), install dust cap, install drum, install wheel, lower and drive :)

May 25, 2010 | 1998 Ford Windstar

1 Answer

Removing front hub assembly


I've never heard a hub make a rattle noise. A bad hub bearing will usually make a roaring or whining noise at speed and/or it will have play in it. When is the rattle noise made, over bumps, at a slow speed, at high speeds?

Jan 02, 2010 | 2000 Jeep Cherokee

1 Answer

How do i repair left front hub & bearing assembly on a 2000 ford taurus v6 24v dohc


BEST TO GET A HAYNES REPAIR MANUAL IT HAS PHOTOS AND INSTRUCTIONS ON HOW TO REMOVE HUB BEARING ASSEMBLY.YOU WILL NEED A 1/2 SIZE TORQUE WRENCH FOR HUB RETAINING NUT.ITS TORQUE IS 170 - 202 FT LBS.MAKE SURE YOUR TORQUE WRENCH MAXIMUM RANGE IS AT LEAST OVER 200 FT LBS TORQUE.YOU WILL ALSO NEED A AXLE NUT SOCKET.ITS A BLACK SOCKET LIKE IMPACT SOCKET.ITS GRADE 8 STEEL.YOU HAVE TO USE THIS TYPE.A REGULAR SOCKET WILL BREAK.WHEN REMOVING AXLE NUT.ITS ON TIGHT.YOU WILL ALSO NEED A 1/2 BREAK BAR TO BREAK IT A LOOSE.ALSO REMOVE WHEEL COVER.WITH CAR WEIGHT ON WHEEL YOU HAVE TO LOOSEN AXLE NUT A LITTLE.NOT ALL THE WAY UNTIL YOU GET CAR OFF GROUND.WORK SAFE BECAREFUL.

Oct 28, 2009 | 2000 Ford Taurus

1 Answer

What tools do i need to replace front wheel bearing hub assembly


Floor jack- jack car up and put a jack stand under it. A tire lug to remove tire. A 36 mm socket to unbolt axle shaft sticking through bearing hub. Next a Brass hammer with a block of wood. Next center wood on axle shaft sticking through bearing hub and hit with a 4lb brass or steel hammer with a wood block on shaft. Next you need a 10mm or 12mm socket on back side of bearing hub should have 3 bolts holding it unbolt. Last use a pry bar and gradually pry bearing out and no there not pressed in like a lot of people think.
(Socket sizes maybe different)
If you take it somewhere it would cost about $800 and up.

May 03, 2009 | 2000 Pontiac Grand Am GT

1 Answer

Sebring wheel bearings


Not 100% sure on size, but ask for TORX socket to fit hub bolts on your vehicle, at local autoparts store.

Mar 06, 2009 | Ford E-150 Cars & Trucks

1 Answer

Front hub/bearing replacement


You will find that after you remove the hub, you will need to take it to someone with an engineering press to get the old one out and press the new one in.
Good luck

Dec 31, 2008 | 2001 Oldsmobile Silhouette

Not finding what you are looking for?
2000 Oldsmobile Silhouette Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...