Question about Cars & Trucks

Open Question

What is the reference number 601 engine fan belt?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I install fan and alternator belt?


question 3 , and double posted....
and still no hint as the the JOB.
what are you doing and why, so we are on same page?

wow,,, you do make this so hard.
if the questions is new belt time"only"?(yes? do i guess good?)
then i posted last post all 11 steps from the real fsm ON REMOVAL. so, now I add page 2.
So now you want ,INSTALL too?
the below only works if you did page 1 correctly

ok here. 11 more steps, totaling 22



Install the drive belt to the crankshaft pulley, the tensioner and the generator.

Rotate the drive belt tensioner clockwise.

Install the drive belt to the idler pulley (1).

NOTE

Important: Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.

Slowly release the drive belt tensioner.

Raise the vehicle.

Install the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Install the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Lower the vehicle.

Install the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Remove the engine support fixture. Refer to Engine Support Fixture .

Install the the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .

Jan 08, 2016 | 2005 Suzuki XL-7

1 Answer

How to install the alternator belt in a 2008 Suzuki xl-7?


which engine option, you do know belts are not same on all engines right? fact.
2.7L V6 or bigger? IDN.

same on all cars. (answering in generic form do to above)
loosen the tension-er.
take off old
put back new
and if not a spring tension-er,set proper tension
the fSM cover all this.
why not read the manual, RTM?

here is one example (get the book, RTM or see alldata.com)

2008 xl7 engine


Removal Procedure

Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .

Install the engine support fixture. Refer to Engine Support Fixture .

Remove the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

Remove the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Remove the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Lower the vehicle


Rotate the drive belt tensioner clockwise to release the drive belt tension.

Slide the drive belt off of the belt idler pulley (1).

Slowly release the drive belt tensioner.

Remove the drive belt from the accessory drive pulleys.

end remove
beg, install



Install the drive belt to the crankshaft pulley, the tensioner and the generator.

Rotate the drive belt tensioner clockwise.

Install the drive belt to the idler pulley (1).

NOTE

Important: Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.

Slowly release the drive belt tensioner.

Raise the vehicle.

Install the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Install the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Lower the vehicle.

Install the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Remove the engine support fixture. Refer to Engine Support Fixture .

Install the the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .
end.

Sep 07, 2014 | 2008 Suzuki XL7

1 Answer

Front seal replacement 5.9 cummins


Hi Dale, I'm glad to help! Below is the removal procedure for the front crankshaft seal on your 5.9 cummins engine. Hope this helps and have an awesome day!



REMOVAL

  1. Disconnect both battery negative cables.
  2. Raise vehicle on hoist.
  3. Partially drain engine coolant into container suitable for re-use (Refer to 7 - COOLING - STANDARD PROCEDURE).
  4. Lower vehicle.
  5. Remove radiator upper hose.
  6. Disconnect coolant recovery bottle from radiator filler neck and lift bottle off of fan shroud.
  7. Disconnect windshield washer pump supply hose and electrical connections and lift washer bottle off of fan shroud.
  8. Remove viscous fan/drive assembly. (Refer to 7 - COOLING/ENGINE/RADIATOR FAN - REMOVAL).
  9. Remove cooling fan shroud and fan assembly from the vehicle.
  10. Remove the accessory drive belt (Refer to 7 - COOLING/ACCESSORY DRIVE/DRIVE BELTS - REMOVAL).
  11. Remove the cooling fan support/hub from the front of the engine.
  12. Raise the vehicle on hoist.
  13. Remove the crankshaft damper and speed indicator ring.
  14. Remove power steering pump.
  15. Remove accessory drive belt tensioner.
  16. Remove the gear cover-to-housing bolts and gently pry the cover away from the housing, taking care not to mar the gasket surfaces. Remove crank seal dust shield with cover.
  17. Support the cover on a flat work surface with wooden blocks (Removing Seal from Cover), and using a suitable punch and hammer, drive the old seal out of the cover from the back side of the cover to the front side(Removing Seal from Cover).

Apr 10, 2014 | 2004 Dodge Ram 2500

1 Answer

Timing belt replacement


Mrs Kelly, the 2004 chevy Tahoe came equipped with 3 different engines. All of which use a timing chain not a belt. The timing chain should last the life of the engine and does not require replacement as does a belt. Now if you are referring to the main fan belt, go to this web site and look for your model / W (engine) for your engines belt routing...

http://www.daycoproducts.com/daycoweb.nsf/DaycoSerpentineBeltGuide.pdf

Dec 17, 2010 | 2004 Chevrolet Tahoe

1 Answer

How do i install a water pump for an Isuzu Rodeo, V.7 3.2 liter


Isuzu_Rodeo_Rodeo_Sport_1997-2004
Water Pump - Removal and Installation

3.2L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Upper radiator hose Timing belt. Refer to the Timing Belt procedure. Idler pulley Water pump
To install:


d2081b9.jpg

Fig. Exploded view of the water pump mounting

3702807.jpg

Fig. Water pump torque sequence. Apply LOCTITE® 262 to bolt number 3 (arrow)-3.2L and 3.5L engines

NOTE Apply Loctite® 262 to bolt number 3 prior to installation.
  1. Install or connect the following:
    Water pump. Tighten the bolts in two passes, in sequence, to 18 ft. lbs. (25 Nm). Idler pulley. Torque to 38 ft. lbs. (52 Nm). Timing belt Upper radiator hose Negative battery cable
  2. Fill the cooling system.
  3. Start the engine and check for leaks.

3.2L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following: Negative battery cableRadiator hoseAccessory drive beltFront coverTiming belt. Refer to the Timing Belt unit repair section.Timing belt idler pulley Water pump
    Negative battery cable Radiator hose Accessory drive belt Front cover Timing belt. Refer to the Timing Belt unit repair section. Timing belt idler pulley Water pump

To install:

e6f48ad.jpg

Fig. Water pump bolt tightening sequence-3.2L engines
  1. Install or connect the following: Water pump. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm).Timing belt idler pulley. Tighten the bolt to 38 ft. lbs. (52 Nm).Timing beltFront coverAccessory drive beltRadiator hoseNegative battery cable
    Water pump. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm). Timing belt idler pulley. Tighten the bolt to 38 ft. lbs. (52 Nm). Timing belt Front cover Accessory drive belt Radiator hose Negative battery cable

  2. Fill the cooling system.
  3. Start the engine and check for leaks.

Hope this help (remember rated and commento).

Mar 19, 2010 | 1997 Isuzu Rodeo

1 Answer

2006 dodge dakota water pump replacement instructions 3.7L


The water pump can be removed and installed without discharging the air conditioning system (if equipped).

  1. Disconnect battery negative cable.
  2. Drain cooling system. Refer to Draining and Filling found under Cooling System, Service and Repair.
  3. Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse. WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094). SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS. CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.
  4. Remove upper radiator hose clamp and hose at radiator.
  5. The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. A Snap-On 36 MM Fan Wrench (number SP346 from Snap-On Cummins Diesel Tool Set number 2017DSP) can be used. Place a bar or screwdriver between water pump pulley bolts to prevent pulley from rotating. Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
  6. 6. If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
  7. Remove fan shroud attaching hardware (two bolts at bottom-two clips at top).
  8. Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
  9. After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
  10. Do not remove water pump pulley bolts at this time.
  11. Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front). When all belt tension has been relaxed, remove accessory drive belt.
  12. 12. Remove four water pump pulley-to-water pump hub bolts and remove pulley from vehicle.
  13. Remove lower radiator hose clamp and remove lower hose at water pump.
  14. Remove heater hose clamp and heater hose from heater hose coolant return tube.
  15. Loosen heater hose coolant return tube mounting bolt and remove tube from water pump. Discard the old tube O-ring.
  16. Remove seven water pump mounting bolts.
  17. Loosen clamp at water pump end of bypass hose. Slip bypass hose from water pump while removing pump from vehicle. Discard old gasket. CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

INSTALLATION

  1. Clean gasket mating surfaces.
  2. Using a new gasket, install water pump to engine as follows: Guide water pump nipple into bypass hose as pump is being installed. Install water pump bolts. Tighten water pump mounting bolts to 40 Nm (30 ft. lbs.) torque.
  3. Position bypass hose clamp to bypass hose.
  4. Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
  5. Install a new O-ring to the heater hose coolant return tube. Coat the new O-ring with antifreeze before installation.
  6. Install coolant return tube and its mounting bolt to engine. Be sure the slot in tube bracket is bottomed to mounting bolt. This will properly position return tube.
  7. Connect radiator lower hose to water pump.
  8. Connect heater hose and hose clamp to coolant return tube.
  9. Install water pump pulley. Tighten bolts to 27 Nm (20 ft. lbs.) torque. Place a bar or screwdriver between water pump pulley bolts to prevent pulley from rotating.
  10. Relax tension from belt tensioner. Install accessory drive belt.
  11. CAUTION: When installing the serpentine accessory drive belt, the belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Illustration above for correct belt routing. The correct belt with correct length must be used.
  12. Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
  13. Install fan shroud.
  14. Install fan blade/viscous fan drive assembly to water pump shaft.
  15. Fill cooling system.
  16. Connect battery negative cable.
  17. Start and warm the engine. Check for leaks.

Feb 28, 2010 | 2006 Dodge Dakota

1 Answer

How to change water pump (1997 sonoma)


The text below is from the GM Service manual 4.3L V6 Engine
Water Pump Replacement (4.3L)
Removal Procedure
Drain the cooling system. Refer to Draining and Filling Cooling System .
Loosen the water pump pulley bolts.
Remove the cooling fan and clutch assembly.

Tools Required
J 46406 Fan Clutch Wrench

Removal Procedure
Remove the upper fan shroud.
Remove the fan clutch from the water pump in a counterclockwise direction using the J 46406 .
Remove the fan clutch assembly.
Remove the drive belt. Refer to Drive Belt Replacement Remove the water pump pulley mounting bolts.
Remove the water pump pulley.
Remove the radiator outlet hose clamp from the water pump.
Remove radiator outlet hose from the water pump.
Remove the water pump mounting bolts.
Remove the water pump from the engine.
Remove the water pump gaskets.
Clean the water pump gasket mating surfaces.
Installation Procedure
Install the water pump gaskets.
Install the water pump to the engine.
Apply a sealer (GM P/N 12346004) to the bolt threads.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
Install the water pump mounting bolts.
Tighten
Tighten the mounting bolts to 41 N·m (30 lb ft).
Install the radiator outlet hose to the water pump.
Install the water pump pulley.
Install the water pump pulley bolts.
Tighten
Tighten the water pump pulley bolts to 25 N·m (18 lb ft).
Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 4.3L.
Install the fan clutch assembly.
Fill the radiator cooling system. Refer to Draining and Filling Cooling System .
Inspect the cooling system for leaks.

Oct 01, 2009 | 1997 GMC Sonoma

1 Answer

I dont have a diagram to run serpentine belt to a toyota camry 03


Hi

Replacing Serpentine belt on a Toyota camry 2003—


Step 1--Examine the belt placement of your Toyota Camry fan belt so that you will remember how to put it back once you have removed it. Refer to the vehicle owner's manual for further information. Locate the pivot bolt on the front passenger side of the engine. Loosen the pivot bolt with a socket wrench.


Step 2--Loosen the adjustment locking bolt that is just below the tensioner pulley with a socket wrench, and then loosen the tensioner pulley to allow the belt to move free.


Step 3--Check the belt for any signs of cracking or irregular wear, so you can fix any problems that may exist with the pulleys. Remove the fan belt from the pulleys on the engine and take it out of the engine compartment.


Step 4--Wrap the new fan belt around each of the pulleys the same way it came out. When you have the belt in place, tighten the tensioner pulley with a socket wrench.


Step 5--Tighten the adjustment locking bolt and the pivot bolt with a socket wrench, and then look over the engine to check that everything is back in place.


Step 6--Turn the vehicle engine on and watch it for a few minutes to verify that everything is operating properly, then turn the engine off.


Please refer to these links for serpentine belt diagrams—

Serpentine belt on a Toyota camry Link 1

Serpentine belt on a Toyota camry Link 2

Please do accept the solution and revert for further assistance.

Thanks
Rylee

Jul 13, 2009 | 2003 Toyota Camry

1 Answer

Changing the water pump on 2000 Jeep Grand Cherokee V6


WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Jan 10, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...