Question about Cars & Trucks

1 Answer

The wheels on my 1032 stopped working, adjusted linkage, belts are good. Jerky and occasional wheel movement before completely stopping. Ideas?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 51,545 Answers

Sorry can not find 1032 make ,model car or truck

Posted on Dec 21, 2016


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Power steering doesnt work well when cold

Squealing means the PS belt is loose or frayed. Replace the belt and adjust the tension correctly. The "bouncing" is caused by the PS pump starting and stopping because the belt is loose.

Sep 08, 2017 | 2002 Toyota Sienna

1 Answer

How do I adjust brakes on a horse drawn amish buggy?

Hi Bill, Tried saying WHOA ? Assuming it's a 'parking 'brake,can you block the wheels and have an assistant apply & release it?look under buggy for movement at the other end. A cable or mechanical linkage near one end or the other should have a provision for adjustment.Use penetrating oil,'shorten' linkage to tighten & vise versa it could also be a 'shoe' type brake applying pressure to wheel[s[ or axle. trace linkage from lever to brake. Good Luck

Oct 19, 2014 | Cars & Trucks

1 Answer

Squeeky noise coming from engine

Sounds like the belt is too loose. It slips and the alternator stops turning and the light comes on. Look online on "how to" adjust the belt.
Good Luck....should be a simple fix.

Mar 02, 2014 | 1996 Geo Prizm

1 Answer

1997 Nissan 200sx. Wheel vibration

jack the car up and give the see if the wheel has any movement left to right or top to bottom. If there is no movememnt then your cv joint is ok and tie rod is good. is the a noise when you make a tight turn left or right , it maybe a wheel bearing. Also you have checked the nuts on the wheel itself are all tight?

Jul 19, 2017 | Nissan 200SX Cars & Trucks

1 Answer

My Toyota vios steering wheel jerky when normal stopping? But after switching off the air-conditioning, the problem gone.

check the tension on your belt that drives the power steering pump and the compressor if tight then the clutch on the ac compressor might be about the freeze up

Aug 17, 2012 | Cars & Trucks

2 Answers

1999 ford explorer limited whining noise in front end

Whining noise is probably in one of the pulleys or belts. Probably the power steering. And the popping is probably CV axles.

Aug 02, 2012 | 1999 Ford Explorer

1 Answer

Hy does my steering wheel have play in it?

Tie rod ends,the Pitman arm,and the idler arm are the most common parts to cause steering wheel play.Even if none of these is worn badly,the play will add up to make it worse.The best way to find the part or parts with excessive play is to observe the linkage while someone moves the wheel back and forth.They should just "twitch" the wheel,not turn it lock to lock.I'm sure you'll see what's worn out(just remember that a little play at the linkage will translate to a lot in the wheel,so if you see ANY exccessive movement that doesn't look right,just replace the part).

Jun 02, 2012 | 1991 Ford F150

1 Answer

1996 Range Rover SE Rear Brake Fluid Leaking right over passeenger side wheel. Computer states (low break fluid) all three brake lights are on. Peddel goes all the way to the end. Very low brake support...

Replace the wheel cylinder on the wheel where you see it leaking then bleed brake system you ought to be ok on your brakes. As for the sun roof sounds like part of the track system is stripped happens all the time on automatic shoulder belts you can hear the motor running but no movement.

Jan 05, 2011 | 1996 Land Rover Range Rover

1 Answer

Shaking when driving. bought new tires in front 18 months ago. bought the car 3 years ago it was already lowered bought back tires six months ago had alighned two months ago started shaking after and tires...

get under the vehicle (use ramps) and check all linkages for movement pull push on the anti roll bar links, pull push on steering rack and pinion and linkages, any excessive movement, jack each wheel at a time, using a bar check the lower wishbone joints for movement, get the bar in the gap between the wishbone and lower part of the shock. and pull down, if any movement in ball joint up and down replace. while wheel on vehicle check for movement in bearing you will feel a tiny amount not much but pull and push on wheel with opposite hands on 12 o'clock and 6 o'clock and do the same at 9 and 3. now with both wheels off the ground but with the tyres still on, have some one holed one wheel and push pull on wheels each side there should be even movement between both wheels, if everything is fine with the the steering linkages and this dose not feel or sound right then this could be the problem also to add if the inside and out side of the tyres are wearing then the tyre pressure is wrong and needs adjusting to the right tyre pressure .

Jul 24, 2017 | 2000 Ford Mustang

1 Answer

4 wheel drive not working

First, check the transfer case and make sure it's full.
If you have the electric shift system in your vehicle, a servo motor could be failing, or the switch may be going bad. Even the switches on these systems are expensive so good, accurate testing must be done to verify failure of anything before you start replacing stuff. If it's not electric, check linkage to transfer case... something may be loose and sliding out of adjustment. Todays systems are just too complex to give accurate answers without hands-on testing. Many times several different items can give similar symptoms. That is why most shops say "bring it in and we will look at it".
good luck

Dec 28, 2008 | Chevrolet TrailBlazer EXT Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14479 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides