Question about Cars & Trucks

2 Answers

Want to know if my 2010 is neg or positive grd

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 40,672 Answers

All electrical systems on vehicles , tractors , mowers for the last 50 years at least are negative ground because of the characteristics of current flow in electricity

Posted on Dec 20, 2016

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 10,938 Answers

If this is a 60 s john deere 2010 positive ground

Posted on Dec 20, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you give a jump start to someone using a 2007 Dodge Charger?


The underhood connections can work by themselves...POS to POS, and NEG to NEG...sometimes dirty/weak connections do not allow the power to transfer fully from the underhood connections...if this is the case then you need to connect directly to the battery in trunk for full power charge...again POS to POS, and NEG to NEG...hope this helps

Jun 09, 2015 | 2007 Dodge Charger SE

1 Answer

Convert battery cables from top post to side mount replacement ends?


If all you are doing is changing to a side post battery, just connect all the positive cables from the old pos post to the new pos holder and all the neg ones to the new neg holder. If you've already cut them all off and not sure where each wire goes, all the reds are positive, all the blacks are neg. To make sure use your continuity meter to test. Connect one meter lead to any good clean metal part on the car and test between each black wire in turn, the neg ones will show a circuit, the pos ones will not.

Feb 10, 2015 | 1993 Chrysler Concorde

1 Answer

Need to reset the anti-theft system on a 2010 Dodge Avenger.


the only things ive heard is if you insert the key into the ignition and turn it to on position and leave it for ten min that might reset it or you can try reseting the whole computer by turning the key to on and unhooking the neg battery cable then the pos cable then holding the breaks down or the horn down to drain the remaing juice the engine holds even after the battery is diconnected leave it unhooked with the key turned to on for about 15 min then turn the key off and hook the battery back up see if that works bud!

Mar 19, 2013 | 2010 Dodge Avenger

1 Answer

Gauge showing low output alt only 1yr old wondering if it could be regulator or batt or wiring


if you have access to a digital multimeter, connect the meter (set to volts) across positive and neg. terminal of the battery, should read roughly 12.6 volts, close to 10 volts, battery may be going out, also test the alt output, disconnect neg term and place negative lead to battery neg post and positive lead to neg battery cable (make sure meter is set to amps) should read near the rating, if both those, then you'd want to do a resistance test, (set meter to Ohms) disconnect battery and connect meter neg to either pos cable terminal or where the pos cable connects to the alt and connect positive lead to opposite of neg, should read next to 0, the check resistance of the ground by connecting meter between batt neg cable and body of alt.

- Spenser

Apr 04, 2011 | 1988 Ford F 250

2 Answers

Jump the battery


What do you need to know? Positive to positive neg to neg. ON the Grand prix it is hard to get to the terminals on the battery. Hook the positive clamp to the postive bolt covered with the red plastic cover near the battery. Neg to the metal part of the engine.

Feb 06, 2011 | 1995 Pontiac Grand Prix

1 Answer

05 grd caravan fuel gauge showed quarter tank and


The float sending unit is messed up and don't know now much gas is in the tank. The float may be stuck in a higher position showing more gas, in reality the gas level is way below. Try using a rubber mallet and tap on the gas tank near the fuel pump. It may help free up the float.

Feb 16, 2010 | 2005 Dodge Grand Caravan

1 Answer

Chevy K5 Blazer military diesel with 12/24v system. Replacing the dual batteries and need to know battery cable pos/neg terminations. Cross connect cable looks like a frame ground. Had it connecting both...


Positive of one battery to hot of vehicle wiring harness--neg. of that battery to positive of other battery--negative of that battery to block (ground)

Aug 04, 2009 | 1984 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...