Question about Mazda Cars & Trucks

Open Question

How many lights should come on at the back of the car when I turn the fog light to the 2nd setting both sides or side mazda 6 2008

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 512 Answers

SOURCE: Fog lights

check fuse #7 in the fuse block inside the vehicle and fuse #25 in the fuse block under the hood...more than likely you blew one of these fuses when it sparked. as for the drivers side being inop once you replace the blown fuse if you have a test light check for voltage at the bulb connector...the light assembly itself may be bad

Posted on Sep 28, 2008

  • 426 Answers

SOURCE: 1991 volvo tail lights

Could you take out a bulb and with a testlight/probe check that you do in fact have power to that circuit .Also check that they are the correct bulb for that application I have seen people put indicator bulbs in where therse supposed to be a double filament bulb.Does the base of the bulbs lead contacts line up with the two steel terminals inside the plug?

Posted on Oct 20, 2008

  • 5 Answers

SOURCE: Mazda 3 tail light on, brake light not on

The bulb actually has two seperate elements in it.
That is why the tail light works fine.

If you take the bulb out you will see the seperate elements.
Change the bulb and it should be fine.

Posted on Jan 10, 2009

  • 51 Answers

SOURCE: change a fog light for a 2006 LR3

There is a circular cover surrounding the fog light assembly that simply pops off. Behind that cover there are three maybe four torx style screw that need to be removed, then simply just disconnect the electrical connector to the fog light assembly.

Posted on Oct 14, 2009

  • 1986 Answers

SOURCE: how to remove broken fog light on drivers side and

Remove black plastic fender cover underneath your bumper. Watch for the two spring screw clips they may fall off put them back on. Now you can see the back of the fog light assembly. You will either see the bulb or a black plastic cover that needs to be turned counter clockwise to remove the bulb.

Posted on Nov 10, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Driver side fog light wont stay on

CLearly a connecting issue. Check wiring pins

Mar 12, 2014 | Mazda MAZDA3 Cars & Trucks

1 Answer

High beam indicator comes on with fog lights

Could your Mazda have daytime running lights? If you checked all fuses, did that include the three in the joint box?

There is an auto light-off control module that is central to all functions you describe. It is assumed that you would only turn on the fog lights with headlights on and set for high beam. If you set the headlight switch to LOW, the module closes the headlight relay to turn on the low beams. If you then turn the headlight switch to HIGH, the module turns on the high beams and allows you to turn on the FOG LIGHT switch, closing the fog light relay and turning on the fog lights. Since this sequence is not working, I suggest checking both high beam lamps as both could be burned out. Other possibilities are a defective headlight switch or the module

Oct 01, 2012 | 2005 Mazda 6

1 Answer

Where is the front fog light relay on a BMW e36 m3

Drivers side near firewall is the the black fuse/relay front power distribution box. Fog light relay is Relay #5 which is in the middle row looking front driver's side fender, 2nd relay on left end. It also controls the taillight.

Mar 04, 2012 | 1995 BMW M3

1 Answer

Install problem with h3 fog light bulb for 2002 wrangler

If it is a double filament bulb, try to rotate by 180 degrees in base, since there is a difference in power and touch of the bottom pins

Sep 10, 2017 | Jeep Wrangler Cars & Trucks

2 Answers

My daughters low beams on her 04 Mazda 3 aren't working. Drivers side went out a month age, we took wire plug off checked it and plugged it back in, tapped on the back of the light and it worked. Then a...

replace the bulbs. when you do this though, 2 things to remember though, check to make sure your conections in the pigtail are tight, and 2nd dont touch with your fingers. the oil from your fingers sits there and cooks when energized and drastically reduces the life of the bulbs. happy holidays.

Dec 24, 2009 | 2005 Mazda 3

1 Answer

When i turn my front fog lights on my L200 warrior pick up , the side lights come on instead of the fog lights . what causes this ?

a short can be causing it wires can be touchin making ur sides lights come on instead of the fog lights

Nov 14, 2009 | 1988 Mitsubishi Pickup

2 Answers

2004 Saab 9.3 Conv Passenger side front & rear fog lights will not work. New bulbs. Why? What to do? Is there a fuse for just those on right side? All other lights work fine.

Sounds like similar problem I had on my older 93 - one side main beam and brake light not working. Turned out to be a problem with the filament testing relay. Got it resoldered and now ok.

Oct 16, 2009 | 2008 Saab 9-3

2 Answers

2006 lexus gs300 tire pressure reset button where is it located?

there is not a reset for the tire pressure monitor system, the system resets its self when all tires are inflated to the proper psi. 35 psi . dont forget about the spare. if all tires are properly inflated check the "2nd set" switch. it is located under the dash on the passenger side. sometimes they get bumped accidently. unless you have a 2nd set of wheels with sensors the switch should be set to "main"

Oct 13, 2009 | 2006 Lexus Gs 300

2 Answers

Mazda 626 1991 back brake ligths not working

Is the fuse for the brake lights OK?
Check for power to the brake light switch at the brake pedal and for power coming from it with brake pedal depressed.

Sep 06, 2009 | 1991 Mazda 626

1 Answer

No fog lights on 92 talon non turbo, FWD

Yes you can have fog lights. You will need to buy the Haynes Manual and it will show you where to attach the wires underneath the harness under the hood. The easist way to do this is the biggy back the fog lights onto the main running lights circuit. NOT THE HEAD LIGHTS CIRCUIT. That way when you turn on the running lights the fog lights come on automatically and the fuse is strong enough to power both, and you could bump up the fuse about 10-15amps, but no more.

Hope that helps!



Dec 05, 2008 | 1992 Eagle Talon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

77947 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8832 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides