Question about Cars & Trucks

1 Answer

Im having heat problems too, changed thermostat twice in a month, just warm air i get..why

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 11,486 Answers

Possibly clogged heater core . or radiator . The water pump impeller worn , not moving coolant as much as it should . How to Fix Car with No Heat Easy watch this video

Posted on Dec 20, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2006 chevy equinox has no heat changed thermostat bled the radiator system im getting a little bit of heat Then I get cold air then starts getting warm again then cold What could cause this?


Are you sure you bled all the air out of the cooling system? This is the symptom of trapped air. There should be little bleeder valves on the engine near the thermostat, they kind of look like front end grease fittings. Open them up while filling and have the front of the vehicle raised to help the air escape.

Jun 16, 2016 | Cars & Trucks

2 Answers

Only get defroster. won't change to other levels.


That heater control is powered by vacuum. There is a small hard plastic vacuum hose going through the firewall next to the brake booster. This plastic line feeds the control panel and is either cracked or disconnected from the control panel. If your heat is only warm, then your thermostat is probably bad.

Dec 06, 2013 | 1993 Plymouth Acclaim

1 Answer

1998 ford expedition overheating problem


try to change the cooling sensor

Dec 23, 2011 | Cars & Trucks

1 Answer

Hiya I have a Vauxhall Astra R Reg and having a few problems.... Around 3 months ago I changed the thermostat as there was only warm air flowing into the car, even after it had been running for sometime -...


Hi and welcome to FixYa!

Yes it can be another thermostat issue. We can't really know the thermostat's life span for it can break in any given time. Regarding the oil issue. It can really be lower on cold start but tends to rise when engine is warm. Since there's no visible leak and no water in oil then you can stop worrying.

Hope this helps and thank you for using FixYa! Have a good one!

Jan 27, 2011 | Volkswagen Polo Cars & Trucks

1 Answer

I have an 03 venture 3.4 the problem im having is heating


the air flow does not have any thing to do with the thermostat
make sure you had the right cabin air filter and put in the right dirrection
the air flow is control by three devices calls mode door actuators, if this goes bad then you may not have enough air flow to a certain area

Mar 05, 2010 | 2003 Chevrolet Venture Passanger

1 Answer

My 1999 cougars heater is blowing out cold air. it blows out warm air on setting one but when i put it on 2 or 3 or 4 its cold i am going to get my anti freeze flushed this week and see what happens but i...


Check the thermostat in the cooling circuit for the heat problem; it could be stuck. As for the O2 sensor.....Check the thermostat first. Its cheaper.

Dec 02, 2009 | 1999 Mercury Cougar

2 Answers

'95 Jeep GCL Heater blows cold air


check vent functions to make sure in heat position vents are fully closed. turn temp switch back and fourth so hear movement of heat vents gl

Aug 29, 2009 | 1998 Jeep Cherokee

1 Answer

Can not get the heater to work


If you have not re-installed the thermostat, then the coolant continually circulates, and will stay as cool as your rad can get it. With thermostat in, it will hold/restrict the coolant to a set temperature approx. 190F-210F and then allow it to flow through for cooling and the cycle begins again. Also make sure you run system with rad cap off for a while with heater on after installing thermostat, to bleed all the air out. Feel the temperature of your heater hoses near the firewall when engine warmed up to normal operating temperature. If both fairly hot, you should get heat, if one hot, one quite a bit cooler, you have a flow problem. That could be a valve not opening, core plugged, weak water pump, for examples. if all that checks out good, then I'd be checking my blend/air door for movement. Let us know what you find.

Nov 16, 2008 | 1986 Toyota Pickup 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...