Question about Audi S3

Open Question

Hi, please explain how to replace 2009 model Audi S3 clutch slave cilinder

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: clutch pedal stays down

Still have air in system.. Try this: Pull pedal up,fill reservoir to the top, open bleed nipple on slave cyl all the way,leave for a while to "gravity feed" keeping the reservoir full,& an eye on the nipple, until all bubbles are expelled and clean brakefluid drips out(could take a few minutes). Close the nipple, and bleed system as usual....

Posted on Jun 24, 2008

  • 208 Answers

SOURCE: Removal of slave clutch master cylinder

The hydraulic cylinder is in the bell housing. When you separate the motor and tranny, you will see it as a unit with the throw-out bearing. Take the hydraulic line off before you start. You will have to bleed it when you are done.

Posted on Aug 13, 2008

  • 3600 Answers

SOURCE: Nubira 2000 model sticky clutch.

Regards Darryl, you have a leak try bleeding the system then lube the contact ball which you should of done when replacing the slave, also could have master going out happens all the time weakest point in the system is the first to go out.

Posted on Jul 01, 2009

daves944
  • 1050 Answers

SOURCE: clutch replaced and slave replaced and master 95' nissian maxima

If you're sure that the system has been bled properly, then you probably have a problem inside the transmission. Could be a broken clutch fork or blown release bearing. Make sure you've checked the hydraulics first though, sometimes it is difficult to get all the air out and you may need to use a pressure bleeder. Most brake shops have these.

Posted on Mar 03, 2010

SOURCE: put new clutch & slave cilinder in my crisler voyager 2003 but now im losing pressure

You either have a leak or not bleed & air
in the system,just like brakes

Posted on Mar 08, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace a audi 500sel 1993 clutch cable


i cant find a clutch cable as a part listed for that car online

you sure it isnt a hydraulic system
clutch slave and master cyl

best way to fix it is tow the car to the audi service center

index-cvxygyvu0vydc25j522ljeey-4-0_2.jpg

Mar 31, 2017 | Audi Cars & Trucks

1 Answer

Sorry my car is Audi A3 2000model 1.8 non turbo. i just changed my slave master cylinder and i tried to bleed my clutch but it doesn't get up. what could be a problem?


the master cylinder slave or cylinder
or both

slave cylinder failure
slave cylinder in inside gearbox housing gear bo out to fix

if replaced both ...still air in the system

if still no better a clutch fork or clutch problem..gearbox out



26326752-ogjx3hr4xss2hzdmdfmqnvvj-5-0.jpg

26326752-ogjx3hr4xss2hzdmdfmqnvvj-5-1.jpg

26326752-ogjx3hr4xss2hzdmdfmqnvvj-5-3.jpg

Oct 25, 2016 | Audi Cars & Trucks

1 Answer

My car is over revving going to 1000 rpm at idle what is it please help Audi A3 s line 2.0 tdi


Revving on Idle ' Audi-Sport.net

www.audi-sport.net > ... > A3/S3/Sportback (8P Chassis)
Feb 1, 2012 - My Car 58 S3, as of last night decided to start revving whilst on idle, I found a clip ... I can do or is it going to be a trip to audi for them to pull my pants down! ... Lots of members all over the UK have VCDS, have a look at the VCDS .....and as the engine warms up it'll auto-rev to 1000rpm every time i sit at idle. Car revving itself on idle ?
Sep 23, 2013
Whining noise when accelerating, any ideas?
Mar 15, 2012
More results from www.audi-sport.net

[FIXED] Audi A4 RPM Idle Problem - YouTube

? 2:48
https://www.youtube.com/watch?v=EG71Jz9l6qY
Feb 5, 2011 - Uploaded by RickyTomatoes
[FIXED] Audi A4 RPM Idle Problem .... whole lot more and sometime i can even feel like the engine is just gonna die. sometimes it does it some other times it does ... Our cars shouldidle at 900. ... AUDI A3 1.6 IDLE PROBLEM!

When getting into first gear, is revving to 2000 RPMs before ...

https://www.reddit.com/.../cars/.../when_getting_into_first_gear_is...

RedditSep 3, 2014 - When getting into first gear, I bring the revs up to around 2000 RPM right ... Being able to get going without any throttle is fairly dependent on car size and ...Thats how I have a 300,000 kay clutch still on my audi with no slippage. ... Clutches ought to last well over 100,000 miles if they are not abused, and ...

Revs going up and down while car is stationary - AudiForums.com

www.audiforums.com > ... > Audi Models > Audi A4 > B7 Models

Jan 21, 2016 | Cars & Trucks

1 Answer

My Audi S3 2009 has had an increase in engine vibration and Revs by itself.


check the engine mounting for damages & transmission mounting.also check the mounting bolt for looseness and tight...

Nov 19, 2015 | Audi Cars & Trucks

1 Answer

Clutch pedal droped raisded back by hand pedal does not depres engine does not start


It sounds like your clutch master or slave cilinder has gone bad .you should be able to locate clutch cylinder under hood usually drivers side check fluid level if low replace master or slave cylinder.

Nov 26, 2010 | 2004 Hyundai Santa Fe

4 Answers

The clutch pedal is rock hard won't go in too gear checked the clutch master cylinder and thats ok, so do you know what the problem is.


Possible solution! Daewoo Lanos 98-99
Had the same problem suddenly the clutch pedal went rock hard!
The clutch was around 3 months old.
Mechanic checked - Master, Slave, Clutch Components, and inside the box, all looked okay.
Turned out the top arm of the clutch pivot rod had twisted, replaced pivot rod around AU$100.
Fixed Problem!

68f141a6-6e26-4193-91d9-bdf12856e824.jpg 8ee95b47-7be0-4e27-81a1-a4ccf7bbc122.jpg

Apr 16, 2010 | 2004 Land Rover Discovery

1 Answer

Audi a3 1996 1.6 5 speeds model. 1st flexi clutch pipe split..no clutch replaced pipe now no gear change..could it be worn clutch? car is in garage! help tp


First you must air bleeding out from inside hydraulic clutch acting system ! On the slave cylinder you will find an aeration screwed ventil provided for air bleeding. See picture below:

ee99bec.png Two person are necessary for this operation. One person for acting the clutch pedal and another person for air bleeding out from inside hydraulic clutch acting system by unscrewing the aeration ventil from slave cylinder. This operation is difficult, and must spend some time for successful result!

Jan 28, 2010 | 2005 Audi A3

1 Answer

Clutch sticks on 1989 audi 100.is it hydrualic?It is engaged even with the pedal down.does it intermittantly.this is a 5 cyl.eng. w/a 5 speed


hi, depending on the model, you may have a mechanical clutch. if there's a clutch master and slave cylinder under the hood, its hydraulic. the main issue here is that your pressure plate. you will need to replace this. this will fix the issue.

Mar 11, 2009 | 1989 Audi 100

1 Answer

How to replace the Clutch Slave Cylinder


hi, your slave cylinder is not to hard to replace just be carefull with the tread at the fitting ,first disconect the line and then the screws that holds it ,be sure to install the little shaft back correctly, after you finish be sure to bleed the cilinder ,(carefull with the tread at the fitting)......

Aug 19, 2008 | Saab 9000 Cars & Trucks

1 Answer

Replaced clutch slave cylinder blew out repalced slave while bleeding blew out again


Could be a couple of different things.
1) your clutch master has a plugged pressure bypass, and it is sending excessive pressure to the slave and blowing it out.
2) The clutch throw out arm is bound, and will not allow the slave to compress it.
3) The replacement slave was defective.

What was the reason for replacing the slave in the first place?

Jul 31, 2008 | Audi A4 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...