Question about Cars & Trucks

Open Question

Replace on off switch - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 PONTIAC BONNEVILLE WIPER SWITCH REPLACE


All GM use the same basic switch so please watch the video on how to replace the switch. How To Install Replace Turn Signal Wiper Stalk Cruise Switch GM Car Truck...

Jun 21, 2016 | Pontiac Cars & Trucks

1 Answer

Winshield wiper delay intermitent module making noises


The wiper delay is in the steering column. It's a small box about 2 x 2 inches with a wiring harness attached. With the testing procedures I found below, you should be able to figure it out. I found wiper delays on eBay for around $10 to $20. Good luck.

WINDSHIELD WIPERS CHEROKEE, COMANCHE & WAGONEER 1. POWER INPUT Remove circuit breaker. Test battery side of circuit breaker. If battery voltage is not present, repair open to splice. Test across circuit breaker terminals. Tester reading should be zero (0) ohms. If not, replace circuit breaker. 2. GROUND Connector A unplugged. Test terminal G. Tester reading should be zero (0) ohms. If not, repair open to ground. 3. INTERMITTENT WIPERS Ignition switch in ACCY. Remove delay module and plug connectors together from the module. If wiper operate in LO and HI speed modes and mist (washer) is working, if wipers and mist operate, replace intermittent module. If not go to step 4. 4. WIPER/WASHER SWITCH Ignition in RUN, wiper switch position as indicated, back probe switch side of connector A for standard, connector B for intermittent: Test connector terminal E-wiper switch in LO and mist/intermittent. If battery voltage is not present, replace switch. test connector terminal C-wiper switch in HI. If battery voltage is not present, replace switch. Test connector terminal F-wiper switch to OFF. If battery voltage is present until wipers stop and then voltage drops to zero (0), system is working fine. If this does not occur, replace switch. 5. INTERMITTENT WIPERS Connector B unplug. Test across terminal A and D while rotating switch from minimum to maximum delay. If tester reading is not between 0-500 ohms, replace switch. Test across terminal A and G while rotating switch from minimum delay to maximum delay. If tester reading is between 0 and 500 ohms, replace wiper module. If not replace switch. 6. WIPER MOTOR Ignition in ACCY, wiper switch position as indicated, probe connector D. Test connector terminal 1. If resistance is no zero (0) ohms,repair open to ground. Test connector terminal 4-wiper switch in any position. If battery voltage is present, replace motor. if is not repair open from fuse panel. Test connector terminal 2-wiper switch in LO. If battery voltage is present, replace motor. If not , repair open from wiper switch. Test connector terminal 2-wiper switch in HI. If battery voltage is present, replace motor. If not , repair open from wiper switch. Test connector terminal 5-wiper switch OFF with voltmeter connected. If battery voltage is present until wipers stop and then voltage drops to zero, system is OK, replace motor. If not, repair open from wiper switch.

62217_jeep1_1.jpg


62217_jeep2_1.jpg

Found on the web. I hope this helps.
Rich Long

Jan 26, 2014 | Jeep Cars & Trucks

1 Answer

Kexus ignition switch replace


To troubleshoot these issue, for ignition switch replacing procedure:---
Click the link below:---


IGNITION SWITCH REPLACING

It depends on vehicle to vehicle. But it's not very difficult on mot of cars to replace ignition switch. Basic theory of replacing ignition switch is same for all car models. -----

To replace ignition switch on your vehicle, I suggest you few helplinks with proper ignition switch replacing procedure. View its details and you can replace ignition switch on your vehicle.

-------------

Click the link below: ------

----------

How to remove ignition switch on VW Car models?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html

-------------

How to replace Ignition Lock Cylinder on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-lock-cylinder.html

--------------


Ford Taurus: Ignition Switch & Steering Column Replacing?

http://repairhelpcenter.blogspot.in/2012/06/ford-taurus-ignition-switch-steering.html

-----------

How to replace Ignition Switch on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-switch-on-acura.html

--------------

How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html

-----------

Ignition Switch Will Not Turn Off?

http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html

---------

These will help.

Thanks.

Dec 06, 2012 | 1993 Lexus Es 300

3 Answers

How to replace ignition switch


It depends on vehicle to vehicle.But its not very diffult on mot of cars to replace ignition switch.Basic theory of replacing ignition switch is same for all car models.:-----
To replace ignition switch on your vehicle,i suggest you few helplinks with proper ignition switch replacing procedure. View its details and you can replace ignition switch on your vehicle.-------------Click the link below :----------------

How to remove ignition switch on VW Car models?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html

-------------

How to replace Ignition Lock Cylinder on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-lock-cylinder.html

--------------


Ford Taurus: Ignition Switch & Steering Column Replacing?

http://repairhelpcenter.blogspot.in/2012/06/ford-taurus-ignition-switch-steering.html

-----------

How to replace Ignition Switch on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-switch-on-acura.html

--------------


How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

------------
1995 Ford Taurus: Ignition switch not turning OFF? http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html
-----------
Ignition Switch Will Not Turn Off? http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html
---------
These will help.
Thanks.


Nov 25, 2012 | Cars & Trucks

2 Answers

Grand scenic indicators not self cancelling


Your turn signal switch is most probably faulty. You will need to replace it. Please, check the videos below. The first video shows a similar problem on a Renault Clio. The second one shows the operations to replace the turn signal switch. I think that the operations are quite similar in most modern cars. Good luck!

Turn Signal Switch Problem - Solved

http://www.youtube.com/watch?v=s0MQvwzXFIk

How to Easily Replace a Turn Signal Switch - Clio 2 and other Renault/Dacia


http://www.youtube.com/watch?v=JKiy-F8pd6o


Turn Signal Switch Problem Solved How to Easily Replace Turn Signal Switch Clio 2 and other Renault Dacia

Jun 12, 2012 | Renault Grand Cars & Trucks

1 Answer

Does any one know how to replace the break light switch on a 97 ford taurus?


My 97 Taurus manual gives these generic instructions...

To replace a stoplight switch, first determine what type of switch you have.

If you have an electrical switch mounted to the brake pedal in the passenger compartment:

* Unscrew the switch.
* Unplug the wires.
* Replace with a new switch. Adjust as needed.
* Plug the wires back in.

If you have a hydraulic pressure switch that is mounted in the brake master cylinder:

* Mark and disconnect the wires.
* Unscrew the switch.
* Screw the replacement switch in.
* Reconnect the wires.

Sep 03, 2011 | 1997 Ford Taurus

2 Answers

No brake lights


If the fuses are ok, replace the brake light switch on the back side of the brake pedal. You can test it by disconnecting the plug from the switch and use a jumper wire or paper clip between posts on the plug, lights come on, bad switch.

Mar 18, 2011 | 2001 Chevrolet Cavalier

2 Answers

Remove/replace starter sloenoid


your Ignition Switch is bad here is how to replace it
The ignition switch is usually mounted to the steering column and is operated by a linkage rod.
NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.
f32-17gif.gif The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch:
  • Remove the ignition switch wiring harness.
  • Unbolt it from its position.
  • Bolt the new switch into position.
  • Attach the witing harness.

May 22, 2010 | Jaguar Vanden Plas Cars & Trucks

1 Answer

Replace ignition 87 4runner


It is probably better to replace the switch.
If it is anything like my 87 4Runner, the switch is pretty worn out anyway. I just replaced the switch wiring harness in mine.
Get a new switch and a Haynes manual at an auto parts store.
The manual describes how to replace the switch.
WAY too much to list here, but pretty simple really.
Good luck :)

Nov 06, 2009 | 1987 Toyota 4Runner

1 Answer

Seems battery being drained


Q1. Engine will not start or is hard to start (Cranks OK) A1 -Ignition lock switch faulty -Ignition coil faulty -Power transistor faulty -Spark plugs faulty -Ignition wiring disconnected or broken -Spark plugs faulty Q2, Engine will not crank A2. Battery discharged Battery cables loose, corroded or worn out Transaxle range switch faulty (Vehicle with automatic transaxle only) Fusible link blown Starter motor faulty Ignition switch faulty Ignition lock switch faulty REMEDY Charge or replace battery Repair or replace cables Adjust or replace switch Replace fusible link Repair starter motor Replace ignition switch Replace ignition lock switch

May 20, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...