Headlights are intermittent on 2004 Acura TL - Acura Cars & Trucks

6ya staff

• 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

SOURCE: AC Not blowing inside of 2004 Acura TL

check the fuse and the relays for the fan motors.if thats ok check to see if it is vacuum operated controls and that none of the pipes are off or split.

Posted on Oct 14, 2008

jpstuhr

• 49 Answers

SOURCE: Replacing HID headlight in 2004 Acura TL

HID Bulb Replacement

A transient high tension (25,000 V ) occurs at the bulb sockets of the high intensity discharge (HID) lamps when the combination light switch is turned ON, it may cause serious electrical shock or electrocution if you do not observe the cautions below.

CAUTION:

• Never turn on the combination light switch before fitting the HID bulbs to their bulb sockets and completing the reassembly of the headlight assembly.
• Do not service the headlights assembly in wet conditions, such as rain or snow, near a sprinkler system, or when your hands are wet to prevent electrocution.
• Do not touch the surface of the HID bulbs with your bare hands and do not stain it with any oils and fats.
• Do not disassemble the inverter unit and the ignitor unit.
• Do not turn on the HID bulb by using a power source other than the battery mounted on your vehicle.

1. Make sure you have the anti-theft codes for the radio and the navigation system, then write down the XM radio channel preset. Make sure the ignition switch is OFF.
2. Turn the combination light switch OFF.
3. Disconnect the battery negative cable, then disconnect the positive cable.
4. Remove the headlight assembly.

1. Remove the Torx bolt using a Torx T20 bit.
2. Turn the cover (A) 45 ° counterclockwise to remove it from the headlight assembly.

1. Turn the socket (A) 45 ° counterclockwise to remove it from the bulb (B).
2. Pull the retaining spring (C) away from the bulb then remove the bulb.
3. Make sure the bulb harness (D) is routed correctly so it does not contact the reflector (E).
4. Install the new bulb in the reverse order of removal. Make sure the notches in the bulb align with the tabs in the headlight.
5. After reconnecting the battery, enter the anti-theft codes for the radio and the navigation system, then enter the customer's XM radio channel presets.

Posted on Feb 13, 2009

James Heindl

• 127 Answers

SOURCE: service code a13

DTC 13: Wheel Sensor (Short to Power/Short to Body Ground/Open)

Posted on Jun 05, 2009

SOURCE: 2004 acura Tl cruise control wont engage

This is a problem you will to take to a shop, If you are mechanically inclined I can help you, but if not I would not mess with it, it could be the button or it could be the controller and could even just be a fuse, check the fuse and if you don't find the fuse blown then let me know if you have a volt meter and what to test this yourself. You are going to be working around the air bag too and if you probe the wrong wire while testing you could break your arm or leg by deploying the air bag by accident. Or your neck.

Posted on Aug 06, 2009

SOURCE: what does the service code B23 on my 2004 acura tl

B is oil and filter change with brake inspection and clean, lube , adjust
1 would be tire rotation
2 is replace engine and cabin air filters
3 is replace transmission fluid

Posted on Oct 30, 2009