Question about Cars & Trucks

1 Answer

I bought a used vats decoder decoder code ID number 10304Will that give the key resistance number

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,587 Answers

You could do that with a simple ohm meter !

Posted on Dec 20, 2016

  • 4 more comments 
  • Frank Davis Sr
    Frank Davis Sr Dec 20, 2016

    I have no key and somebody took vats decoder module out befor I got it

  • Frank Davis Sr
    Frank Davis Sr Dec 20, 2016

    Thanks any way

  • Frank Davis Sr
    Frank Davis Sr Dec 20, 2016

    I was hoping the decoder Id # that came with module meant some thing thank you

  • Jeff Armer Dec 20, 2016

    It just tells the resistance of the key pellet .

  • Jeff Armer Dec 20, 2016

    http://www.clksupplies.com/products/lock...

  • Frank Davis Sr
    Frank Davis Sr Dec 20, 2016

    Thanks again went with vats bypass module

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1990 oldsmobule delta 88 royale brougham will not start when security light flashes. i have not the original key and i have a replacement key and lock cylinder


This is a very common problem on GM vehicles. The security system is known to fail. Basically when you insert your key, the system checks for certain OHMS resistance. If the system cannot get the correct signal from the key, it assumes the key is incorrect and goes into SECURITY lockout mode. (prevents hotwiring) This has been happening with GM;s for a very long time. There are ways to bypass this now. Read through this page for info, solutions as well.

http://www.diy-gm-security.com/

Nov 25, 2017 | Oldsmobile Cars & Trucks

1 Answer

I was given a 99 oldsmobile aurora without the key. So after drilling out the ignition I need to either figure what the resistance is for this car or bypass the VATS. Any suggestions?


should have went to a dealer for a key cut by using the vin number --or bought a new ignition cylinder ---this is fixya a repair -fix it forum --not auto theft 101 we dont assist in hacking or by-passing Vehicle Anti-Theft systems

Sep 11, 2017 | Oldsmobile Cars & Trucks

1 Answer

How to disable the vats security system on my 2001 oldsmobile alero?


you cant disable it, its a pass key system not a vats system (vats reads a resistance value in the key). The ignition cylinder has a sensor in it that measures a rotating resistance (then translates into a voltage reading) that the bcm reads to let the car know to start. Usually you can try and start the car, then the security light will start flashing - leave the key in the on position for ten minutes until the security light goes out. Then turn the key off, wait, then try and restart - they usually relearn the code after the first 10 minute try. Sometimes it takes three 10 minute cycles.

Jan 01, 2015 | 2001 Oldsmobile Alero

1 Answer

Need key code via vin number


Your dealer should be able to do this, however if you have a security system VAT, you will need the system checked so you can get the correct key blank. The chip on the key creates a certain amount of Ohms of resistance, that matches your security system. If you use the wrong one the car will not start. There are methods to by pass, however you need your old key, even if its broken to do.

Aug 24, 2014 | 1998 Buick LeSabre

2 Answers

I have a 92 Oldsmobile Toronado that was recently broken into and my igniton was broke. And now I can't start it. I can put the key in it and turn like usual but the information center is saying starting...


I believe that your key has a resistor chip. You will need to find the resistance of your chip. Once found, go to an electronics store and buy a resistor with the same value. Follow the two wires that go from the ign switch down the steering column , into a 2 wire plug into the ign module. Unplug the connector. Plug the resistor to the module. The module will read this value and allow you to start the car.

Nov 24, 2013 | Cars & Trucks

1 Answer

Bypassing 92 cadillac deville vats system


There are ways to bypass the system, but without knowing what the correct resistance in the chip is, its not going to be easy or cheap.
There are a dozen or so different chips, each with a different resistance. The resistance completes the circuit for the VATS system sensor. You can buy a trick box to wire into the circuit, or have the computer changed to skip the VATS signal.
As long as the computer you have now does not get the signal from the VATS the injectors will not work.

Jul 18, 2013 | 1992 Cadillac DeVille

1 Answer

How do i get my 2000 saturn sl to start after installing a new ignition


Did you use the correct ignition switch lock cylinder for the key code you have? If not the security system is activated. You must measure the resistance of the wire in the shaft of the old key and then order it based on that which translates into a code number.
Vats/Passkey Key Codes & Resistances
(Ordered in KEY BLANK numbers from 1 to 15, Resistances in Ohms)
9_20_2012_5_21_40_pm.jpg

Sep 20, 2012 | 2000 Saturn SL

2 Answers

Resister pallet fell out of my key. How do I bypass the decoder?


Go to this link, you can do a key bypass to get around that missing pellet. On this link, is listed under "temporary fix"

http://vatspasslockpasskeysecurityhelp.yolasite.com/

Dec 27, 2011 | 1990 Chevrolet Camaro

2 Answers

1999 Monte Carlo 3.1 theft deterrent


i would get the correct key... most locksmiths carry the GM keys

Sep 12, 2009 | 1999 Chevrolet Monte Carlo

2 Answers

91 camaro


The VATS system has 15 possible ohmic variations in the key .One might use an ohm meter and measure the resistance in your key as this is simply a resistor producing an ohmic value which must match the resistance value the VATS module wants to see. There is a 2 wire key reader in the ignition cylinder that sends this signal to the VATS module looking for a match.One may surf the web and see ways to bypass VATS but I have never tried this and its is fairly sophisticated process which requires an accurate DVOM meter that reads OHMS

Jul 16, 2009 | 1991 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14331 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...