Question about Ford Cars & Trucks

2 Answers

Location of crank shaft sensor on 03 ford escort zx2 2.0 L Fuel injected

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,363 Answers
Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 76,164 Answers

The crankshaft position sensor on the Ford Escort ZX2 is located behind the exhaust manifold. It sends a signal to the computer that includes the speed of the crankshaft, or engine rpm, and the location of the crankshaft at the No. 1 cylinder. The computer uses this information to adjust engine timing. If the sensor malfunctions, the engine will not start

Instructions

1

Disconnect the negative battery cable, using the appropriate wrench. Set it aside, ensuring that it does not touch metal. Raise the vehicle, using the floor jack. Support it with jack stands.
2

Remove the exhaust manifold, using the appropriate sockets to unbolt the manifold at the pipe and at the head. Unplug the crankshaft position sensor, using your fingers.

3

Remove the sensor's retaining bolts, using the appropriate socket, and then remove the sensor from the engine.
4

Lubricate the new O-ring for the sensor with clean engine oil. Install the O-ring on the sensor. Install the sensor and tighten the bolts to 60 inch-pounds of torque. Plug in the wiring harness connector.
5

Reinstall the exhaust manifold. Lower the vehicle off the jack stands, using the floor jack. Reinstall the negative battery cable.

Posted on Dec 19, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: ATS(Air temp sensor) CTS( Coolant temp sensor)

I have a 351 but they are common sensors and should be located same places. ATC is on the side or bottom of the air intake filter box. The CTS should be located on the goose-neck where your Thermostat is housed; this is comming off the intake mannafold and into the radiator.

Posted on Oct 03, 2008

jschoon77
  • 55 Answers

SOURCE: crank shaft sensor

I have 10 years experience in a Nissan dealership and I know without a shadow of a doubt that the Crankshaft Position Sensor is NOT located next tp the crank pulley... it is rather at the other end of the engine near where the transmission bellhousing bolts to the engine block. It is on the side toward the firewall near the bottom. Even if you can get the vehicle on a lift and get under it, you can't really see it... It's more of a feel thing... There was a campaign (recall) on these engines to replace Crank Position and also Cam Postion sensors. Check with your dealer- the campaign might be open. You will need your VIN number when you call.

Posted on Oct 29, 2008

  • 1 Answer

SOURCE: 2005 Subaru Baja Crank Shaft Position Sensor

is there a problem using e10 ethonal in a subaru impreza wrx 2003

Posted on Nov 24, 2008

  • 289 Answers

SOURCE: Ford escort 1996 Fuel Relay

hi..Your fuse panel is right below your steering column
to the left. It is mounted to the left side of your interior.
Open your door, get on your hands and knee's, and
look straight it may be a little up depending on how it
is mounted.
check it out..
thank u..
rate me..

Posted on Feb 27, 2009

mkv0525
  • 358 Answers

SOURCE: PO340 Crank Shaft Sensor "A"C came up as the problem Also a C1201 Just want to find out where the Crank Shaft Sensor is located. Thank you

89119318this should help.

Posted on May 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why my 97' f-250 7.3 powerr stroke keeps dieing while idling


The power stroke engine has several things that will cause this problem #1 crank shaft sensor AKA cam shaft sensor on crank shaft located on passenger side of engine near crank shaft pulley # 2 IPC sensor Injection pressure control if has oil in sensor replace it & wiring pigtail .#3 high pressure oil pump not up to par. #4 injection pressure regulator solenoid they get sticky. with a good scanner that has FORD enhanced software you can check all of these without leaving the drivers seat and perform running tests on injectors and test the ficm module interface with the pcm. Fuel Injection Control Module & Power Control Module.

May 02, 2014 | Cars & Trucks

2 Answers

FUEL INJECTERS NOT FIRING


Fuel injectors not firing most commonly are caused by a bad crank sensor, or check to see if the emergency fuel cutoff is tripped-look too to see if you have a blown fuse, or a bad relay. You can often switch relays around and if the problem follows the relay, there's the problem. Most usual cause, though from my experience, is the crank sensor.

Apr 07, 2014 | 1999 Ford Expedition

1 Answer

Timind belt diagram


i would say your looking at a faulty cam shaft sensor..its located on front side of engine. this fixed the same problem i had..there are 2 sensors one being your cam shaft sensor (normal to go out) and the crank shaft sensor..these work inline with computer to determine correct timing.hope this helps

Dec 07, 2011 | 2000 Ford Escort

1 Answer

I need a fuel system diagram for a 1998 ford escort zx2, we are trying to replace the crank sensor


The crank sensor is located on the block at the front of the engine bay. You may have to remove the catalyst to get to it. It is held in place by a torx screw and has a two wire connector.

Sep 06, 2010 | 1998 Ford Escort

1 Answer

I HAVE A 1998 FORD ESCORT THAT CRANKS OVER BUT WILL NOT START. TRYED STARTER FLUID, AND I DO HAVE SPERK AT THE PLUGS. ANY SUGESTIONS?


Check compression. This car is fuel injected right? Check for fuel at injectors.
Timing belt good not loose (supposed to be changed approx every 60,000 mi.)

May 11, 2010 | 1998 Ford Escort

2 Answers

Have a 2001 Ford F-350 Super Duty 7.3 L Diesel... with a 30 HP Ford chip. Truck started having "hiccups", like it wanted to cut out and quit running. Took to have cam shaft censor replaced on a recall...


Have you tried removing the chip, reseting the pcm, then test drive without the chip, I do not work on diesels but I know I have had some 5.0s with compatibility problems with performance chips, for some reason on select cars the emissions system would through a fit and make the car run like crud with the chip in ran fine with it out although they accused it ran fine for a few months with the chip. if you havent you might try this just to see

Mar 27, 2010 | 2001 Ford F350 Super Duty SuperCab

1 Answer

I own a 1995 ford escort. suspect that the fuse for the fuel pump is bad. Can't locate.


Fuse should be labeled as fuel pump or fuel injection. Fords also have a fuel pump relay, a fuel pump shut off button, reset, under dash by the hump, in case of crash.
Could be the pump itself.

Mar 13, 2010 | 1995 Ford Escort

1 Answer

Fuel filter location for 94 ford escort lx


on the fuel injection engines the fuel filter is located in one of 2 places 1, under and to the rear of the engine above the drive shafts or 2, under the car at the rear just forward of the rear suspension assembly

Apr 25, 2009 | 1995 Ford Escort

1 Answer

1993 ford escort wagon,no electric to injectors


The fuel delivery system uses an electric fuel pump to provide high-pressure fuel to the fuel injectors. The fuel pump is located at the rear of the vehicle, mounted in the fuel tank. It can be accessed by removing the rear seat.

The fuel tubes leading from the fuel tank to the engine are under pressure during vehicle operation. When the engine is turned OFF, the fuel in the fuel tubes remains pressurized for long periods of time to provide quick start-ups. Fuel not used by the fuel injectors during operation is routed back to the fuel tank through the fuel return tube.

The fuel handling components are protected by three fuel filters. A replaceable in-line fuel filter is located inside the engine compartment between the fuel tank and fuel injection supply manifold. A serviceable filter screen is located inside the fuel tank at the fuel pump inlet. A non-serviceable filter screen is incorporated into each fuel injector.


I can get you trouble shooting tips if you want them.
58866017
125387887

Nov 18, 2008 | 1993 Ford Escort 4 Door

1 Answer

98 escort 2lt.


Does this pertain to the Crank Shaft or the Ignition sensor? I've never heard of a crank sensor... I'll check...

I found this from a guy on another website..."It does however have a crank sensor and if you look at the lower crank pulley just to the back of the pulley and go around the pulley you should find the sensor mounted on a bracket. You should see what appears as a sprocket with widely spaced teeth on the engine side of the pulley. This "sprocket" so to speak is what the crank sensor "reads". I believe that the crank sensor is the only sensor used for engine timing. "

Good Luck

Oct 26, 2008 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...