Question about Cars & Trucks

1 Answer

How do I control speeds for the slasher - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,804 Answers

You mean the 'flasher', the directional indicators? You can't, as long as all the bulbs are lit, the lights will flash at the rate for the flasher unit. If one bulb fails, the lights will flash quicker.

Swapping out flasher bulbs for LEDs often causes load problems and flasher speed rate.

Posted on Dec 19, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just new to the tractor driving and was not shown how to start it I have a Fiat 540 special with a slasher attached. What is the configuration to start . I get a light on dash but no spark .thank you


to start with , brake on , clutch in , sit in the seat as there are safety switches in the start circuit
get some one who is familiar with the machine to show you how to operate it

Apr 02, 2017 | Fiat Cars & Trucks

4 Answers

How to fix cruise control on a 2006 ford freestar, does not work at all, wont turn on


Note the diagram, at least check the fuse. Check trouble codes, related to cruise control. to check codes yourself, at least, you need an obd2 code reader that will read po codes as well as manufacturer specific codes. It is worth the investment, in my opinion. Make sure the brake lites work.
cruise 1-hvxehrcewwphuchbcyrcpopp-5-0.jpg

cruise 2-hvxehrcewwphuchbcyrcpopp-5-2.jpg

Mar 05, 2017 | Ford Cars & Trucks

1 Answer

Blower fan not working at all 2004 Buick rendezvous


Which system ?
HVAC Systems - Manual HVAC Systems - Automatic
If automatic it's probably the blower motor control processor .
Blower Motor Control Processor The blower motor control processor is an interface between the HVAC control module and the blower motor. The blower motor speed control, Blower motor speed signal, battery positive voltage and ground circuits enable the control processor to operate. The HVAC control module sends the commanded blower motor speed to the control processor through a 0 to 12-volt linear ramped blower motor speed control circuit. As the blower motor speed control voltage increases, the blower motor speed increases. The control processor sends the actual blower speed to the control module through a 0 to 12-volt blower motor speed signal circuit. The processor supplies 12volts to the blower motor through the blower motor voltage supply circuit. The control processor uses the blower motor ground as a low side control to adjust the blower motor speed.

Nov 19, 2016 | Buick Cars & Trucks

1 Answer

Where is the cruise control fuse located?


In the SJB - smart junction box , Under the dash ! There are three fuse's - F2.27 10amp - F2.32 10amp - F2.17 15amp . Is your air bag light lit ?
SECTION 310-03: Speed Control 2004 Taurus/Sable Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 07/02/2003 Speed Control The vehicle speed control system consists of the following components:
  • Brake pedal position (BPP) switch
  • Speed control actuator cable
  • Speed control switches
  • Speed control deactivator switch
  • Speed control indicator
  • Speed control actuator
  • Smart junction box (SJB)
NOTE: The clock spring provides the electrical interface between the steering column wiring and the speed control switches in the steering wheel.
The inputs to the speed control actuator are:
  • Vehicle speed signal
  • Speed control switches
  • Brake pedal position (BPP) switch
  • Deactivator switch
The outputs of the speed control actuator are:
  • Speed control indicator lamp
  • Speed control actuator cable controlling the throttle position

Apr 01, 2016 | 2004 Ford Taurus

1 Answer

2007 Ford five hundred cruise control turns off when you hit a bump


First off the cruise control is computer controlled , need to check for diagnostic trouble code's . Your vehicle has electronic throttle control also . If your don't have a factory or professional grade scan tool your odds of being able to fix this yourself is close to zero ! You could find a wiring diagram an do some voltage drop testing ,mite find lose connection .
Speed Control
The speed control system consists of the following components:
  • Speed control switches
  • Speed control deactivator switch
  • Speed control indicator
  • Powertrain control module (PCM)
  • Electronically controlled throttle body
  • Clockspring
The speed control system is controlled by the PCM. The speed control system is designed to maintain a selected vehicle speed between 48 and 200 km/h (30 and 124 mph). The speed control system is controlled by the steering wheel mounted switches (ON, OFF, SET+, SET-, CANCEL, and RESUME), and the brake pedal. The steering wheel mounted switches are hardwired to the PCM.
The speed control functions include:
  • Turning the speed control system on.
  • Setting and maintaining the desired vehicle speed.
  • Accelerating the vehicle speed.
  • Decelerating the vehicle speed.
  • Resuming the prior vehicle speed.
  • Turning the vehicle speed control system off.
  • Canceling the speed control.
The clockspring provides the electrical interface between the steering column wiring and the speed control switches in the steering wheel.
The inputs to the PCM are:
  • Output shaft speed (OSS) sensor
  • Speed control switches
  • Stoplamp switch
  • Speed control deactivator switch
  • SJB messages
The outputs of the PCM for the speed control system are:
  • Speed control indicator lamp
  • Throttle command
The throttle position is completely controlled by the PCM through the electronically controlled throttle body. Speed control electronics are contained entirely within the PCM.
When the speed control system is active, the PCM corrects for deviations in the actual vehicle speed by proportionally moving the throttle plate. The PCM modulates the throttle to minimize error between actual vehicle speed and the desired speed.
The PCM strategy uses the throttle control for smooth accelerations.
The PCM sends a serial message over the controller area network (CAN) to the instrument cluster whenever the speed control telltale should be turned on or off.
In the event of an OFF command or a deactivation request from the deactivator switch, the speed control system carries out a hard deactivation and immediately returns the throttle to the idle position.
In the event of a CANCEL command input, the system deactivates and the throttle returns to the idle position at a smooth and controlled rate.
The speed control system provides self-diagnostics. The speed control system is disabled anytime an error is detected in the system. No cluster telltale or message center messages are displayed when faults occur. Fault codes are logged by the PCM.
An electronic throttle control (ETC) system fault also causes the speed control system to be disabled. In this case, an ETC system warning indicator or message center message is displayed.
Additionally, the following conditions cause the speed control system to deactivate:
  • Transmission gear selector is put into a position other than D or OD.
  • Parking brake is applied.
  • Speed control set speed is over-ridden with the accelerator pedal for a period longer than 5 minutes.
  • Vehicle speed loss from set speed of greater than 16 km/h (10 mph) occurs.
  • Vehicle speed falls below the minimum allowable limit of 48 km/h (30 mph).
  • Speed control switch is pressed or stuck longer than 2 minutes.
  • Powertrain Control Module (PCM) Diagnostic Trouble Code (DTC) Index DTC Description Action P0579 Cruise Control Multifunction Input A Circuit Range/Performance Go To Pinpoint Test C . P0581 Cruise Control Multifunction Circuit High Go To Pinpoint Test C . P0720 Output Speed Sensor Circuit REFER to the Powertrain Control/Emissions Diagnosis (PC/ED) manual. P0721 Output Speed Sensor Circuit Range/Performance REFER to the Powertrain Control/Emissions Diagnosis (PC/ED) manual. P1500 Vehicle Speed Error REFER to Section 307-01A or Section 307-01B . P1501 Vehicle Speed Error REFER to Section 307-01A or Section 307-01B . P1703 Brake On/Off Failure Go To Pinpoint Test B .


    Transmission Control Module (TCM) Diagnostic Trouble Code (DTC) Index DTC Description Action P0720 Output Speed Sensor Circuit REFER to Section 307-01A . P0721 Output Speed Sensor Circuit Range/Performance REFER to Section 307-01A .

Mar 04, 2016 | 2007 Ford Five Hundred Limited Sedan

1 Answer

What would make passenger brake light stay on


Is it the brake light or the tail light? When you park and get out of the vehicle and see the rear light on put the indicator/slasher stalk in the central position. If it is in the left or right turn position it acts as a parking light on some cars so that a collision does not occur. It is a safety feature. If you put the flasher/indicator stalk in the central position and the light still stays on then you have an issue. Try it

May 31, 2015 | 1990 Nissan Pathfinder

1 Answer

Cruise control stop working light dont show on dash can a fuse be out if so where is it located


There are three fuse's in the smart junction box , do you know where it is ? It's under the dash panel left side ! The fuse's are F2.27- 10amp , F2.32 - 10amp , F2.17 - 15 amp . They power the speed control servo ! Maybe the control switch's on the steering wheel don't work.
A little back ground on the system ! Speed Control The vehicle speed control system consists of the following components:
  • Brake pedal position (BPP) switch
  • Speed control actuator cable
  • Speed control switches
  • Speed control deactivator switch
  • Speed control indicator
  • Speed control actuator
  • Smart junction box (SJB)
  • Principles of Operation
    The speed control system is designed to maintain vehicle a set speed above 48 km/h (30 mph). After the speed control ON switch is pressed, pressing the speed control switch SET/ACCEL will activate the speed control actuator. To increase a set speed, either press and hold for continuous acceleration, or momentarily tap the speed control switch SET/ACCEL for 1.6 km/h (1 mph) acceleration increments. To decrease a set speed, press and hold the speed control switch COAST until the target speed is reached, or momentarily tap the speed control switch COAST for 1.6 km/h (1 mph) deceleration increments. When the speed control system has been disabled by tapping the brake pedal, the speed control switch RESUME can be pressed and the vehicle will return to the original set speed if the vehicle is traveling over 48 km/h (30 mph) and the speed control switch OFF has not been pressed.
    NOTE: The deactivator switch is provided as an additional safety feature. Normally, when the brake pedal is pressed, an electrical signal from the brake lamp circuit to the speed control actuator will deactivate the system. Under increased brake pedal effort, the deactivator switch will open and remove power to the speed control actuator, releasing the throttle independently of the speed control actuator.
    NOTE: The clockspring provides the electrical interface between the steering column wiring and the speed control switches in the steering wheel.
    The inputs to the speed control actuator are:
    • Vehicle speed signal
    • Speed control switches
    • Brake pedal position (BPP) switch
    • Deactivator switch
    The outputs of the speed control actuator are:
    • Speed control indicator lamp
    • Speed control actuator cable controlling the throttle position
    • Inspection and Verification
      NOTE: If any concerns are noted with the speedometer, stoplamps, or horn, address those concerns by referring to the appropriate sections before continuing speed control diagnosis.
      1. Verify the customer concern by operating the speed control system.
      1. NOTE: Any aftermarket modifications, including but not limited to those listed below, may cause the speed control to not operate correctly:
        • Any wiring or lamp modifications affecting the brake lamp operation
        • LED brake lamps
        • Non-factory installed trailer wiring
        • Radios (speed sensitive, auto mute)
        • Remote starters and alarms
        • Lighting and electrical accessory modifications
        Visually inspect for obvious signs of mechanical or electrical damage:
        • Visually inspect the speed control actuator and accelerator controls.
        • Visually inspect the speed control cable without removing it and ensure smooth cable operation. Inspect the speed control cable connection to the throttle body.
        • Visually inspect the accelerator cable without removing it and ensure smooth cable operation. Inspect the accelerator cable connection to the throttle body. Also check for cable interference with the carpet, bulkhead grommet, insulation and instrument panel wiring.
      1. Visually inspect for obvious signs of mechanical and electrical damage.
      2. Visual Inspection Chart Mechanical Electrical
        • Speed control actuator cable
        • Throttle linkage
        • Battery junction box (BJB) fuse(s):
          • 4 (40A)
          • 12 (60A)
        • Smart junction box (SJB) fuses:
          • 14 (15A)
          • 57 (10A)
        • Wiring harness
        • Loose or corroded connections
        • Deactivator switch
        • Brake pedal position (BPP) switch
        • Speed control switches
        • Powertrain control module (PCM)
        • Speed control actuator
        • Bulb

Mar 14, 2015 | 2007 Ford Taurus

1 Answer

I have a case 430 skid steer 06 mod. I want to know how to run a slasher attachment with out holding the 4 in 1 leaver open all the time, need to know how to get hydraulics to free flow !!!


you will need a separate hose from the pump through a valve to the slasher motor. Talk with an accredited hydraulic shop and they will explain how it can be done

Aug 17, 2014 | Cars & Trucks

1 Answer

TE20 injector pump and engine oils contaminated with diesel


Check the injectors one is sticking open or maybe more are.

Jun 24, 2017 | Cars & Trucks

2 Answers

My cruise control does not work on my 2003 Ford Focus


Hi Fred,

There are several things that can cause your cruise control to not function. Anything from a bad speed sensor to a faulty speed control servo. It is impossible to tell you what is wrong without diagnosing your speed control system. Here is a quote from the vehicle manufacturer regarding this issue:

"Start by running speed control servo integrated self test diagnostics. The servo has integrated self test diagnostics which is a key tool in quickly and accurately diagnosing speed control system faults. Self test diagnostics are also the basis for starting speed control trouble shooting."

Please note that a diagnostic scan tool capable of accessing the speed control data is required for performing this task.

Oct 15, 2011 | 2003 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...