Windshield washer is pumping out of one side only

Looks like a Body Control Module communication issue.

Windshield Washer
When the washer switch is pulled towards the driver, the SASM sends the washer request to the BCM over the LIN. The BCM activates the windshield wash relay (internal to the BCM) and sends a message to the driver side windshield wiper motor. When the BCM activates the windshield wash relay, voltage is provided to the washer pump, directing washer fluid to the windshield. When the switch is released, the windshield wiper motor continues to activate the windshield wipers for 3 additional wipes and then turns the windshield wipers off.

https://www.justanswer.com/ford/74red-focus-2012-ford-focus-se-need-wiring-diagram-washer-pump.html

..

The washer fuse should have power (battery voltage) while the ignition switch is in the RUN position. Verify both sides of the fuse have power. If the rear wash functions them it's not the fuse.

The switch signals the Body Control Module (BCM). The BCM energizes the front washer relay.

Input to BCM from switch is BCM connector C1,24 PK. Output from BCM to relay is connector C4 15 OG.

You need to verify continuity from the the switch to the BCM and from the BCM to the relay.

Comment below for further assistance.

Do you know how to test automotive electrical circuit's using a DVOM - digital volt ohmmeter ? Do you know what a wiring diagram is an how to read one ? Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. year , make , model an engine size. Under system click on body & accessories ,then under subsystem click on wiper/ washer's . Click the search button then the blue link.

Windshield Wiper/Washer System Components
The windshield wiper/washer system consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor
• Windshield washer pump
• Windshield washer relay
• Outside moisture sensor
• FRT WIPER 25A fuse
• W/S WASH 15A fuse
Windshield Wiper/Washer System Operation
Accessory voltage and ground is supplied to the windshield wiper motor and provides the power for operating the wiper motor and logic power to the wiper motor module. The WASH, MIST, LOW, and DELAY modes are controlled by the windshield wiper/washer switch through a series of internal resistors. The windshield wiper switch supply voltage circuit is a 12-volt reference from the wiper motor module to the wiper/washer switch, and the switch position determines the point on the resistor assembly where the reference voltage is applied. The windshield wiper switch signal 1 circuit supplies the voltage from the resistor assembly to the wiper motor module and the signal voltage determines the operating mode. High speed operation is controlled by the windshield wiper/washer switch through the windshield wiper switch high signal circuit. The windshield wiper switch high signal circuit is supplied 12 volts by the wiper motor module and when the wiper/washer switch is turned to the HIGH position the windshield wiper switch high signal circuit is grounded through the switch ground circuit. The windshield washer pump is controlled through the windshield wash relay. The windshield wash relay coil and switch is supplied battery positive voltage, and during WASH mode the wiper motor module grounds the washer relay control circuit energizing the relay. When the relay is energized battery positive voltage to the switch side of the relay is supplied to the washer pump control circuit.

The is the symptom of a defective wiper switch.

There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Windshield Washer Pump

1990 Ford Truck F150 1/2 ton P/U 2WD 5.0L FI 8cyl

The Windshield Washer Pump is located: Under hood, driver side front side of wheelwell, mounted inside washer bottle.here's the part. TAAP Windshield Washer Pump 7 664 1990 Ford F150 1 2 ton 2WD 8...

Is your wiper fluid level good?Look for leaks at pump,it's connected to container,also check your hoses leaving pump to windshield,could be loose or binding.

Mostly in rear side panel with the bottle to fill. Some models have two pumps in front under bonnet at bottle base

the pump is in the washer fluid tank, they are replaceable

the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal

1. Disconnect the battery ground cable (14301).
   
2. Raise and support the vehicle.
   
3. Remove the RH wheel (1007).
   
4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
   
5. Remove the windshield washer reservoir top bolt.
   
   
6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
   
7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
   
8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
   
9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
   
10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.
    
    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.
    
    
11. Loosen the two windshield washer reservoir side bolts.
    
12. Remove the windshield washer reservoir by sliding it out of the side slots.
    
13. Remove the windshield washer pump.
    
    Installation

To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).