Question about Cars & Trucks

Open Question

The acuator, not the sensor - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loss of power


Disconnect the actuator and see if the problem goes away. If it does, replace the actuator. If the problem persists then look at MAP sensor as the possible culprit

Apr 18, 2014 | 2005 Nissan Pathfinder

1 Answer

Engine light and battery light on


first check your alternator for proper voltage 13.5 -14v is okay.Autozone checks it for free just drive up to the store and ask an assosiate.the engine may come on because of low voltage to the sensors or acuators.

Jul 20, 2012 | 2005 Scion tC

1 Answer

Stepped on gas on my 2004 mercedes c240 and no acceleration then engine light came on, whats going on ?


If the sensor in the pedal value sensor fails the system,switches over to the second one .The throttle will be limited to 60%. A electronic throttle acuator will be the solution

Mar 28, 2012 | Mercedes-Benz C240 Cars & Trucks

1 Answer

1993 infiniti all power door stop working except for driver side, what could cause it?


A broken wire at the unlock sensor located at the driver actuator maybe fault or the acuator harness itself and not being able to send the signal out

Mar 06, 2012 | Cars & Trucks

1 Answer

4wd will not engage vacuum pump fine


the sensor for the acuator might be bad or the acuator its self

Dec 23, 2010 | 2001 Ford F350 Super Duty SuperCab

1 Answer

My 1992 corvette does not blow hot air. I can control air flow.


Is the inlet and outlet heater hoses hot and if so you have a seperate acuator for your hot/cold door.Check for vacuum there if you have vacuum to the acuator then it must be a faulty acuator or jambed door.

Dec 21, 2009 | 1992 Chevrolet Corvette

1 Answer

4 wheel drive wont engage to front end drive shaft is turning and actuator is moving


acuator at transfer case or at frt diff if acuator is moving then axles to wheels should be turning and you may have a hub locking problem. if axles to wheels dont turn then the acuator tofront diff is no good not strong enough or bent shaft on acuator, some of these use a small shaft in front of actuator also make sure if this truck use this shaft check it for wear, lift truck remove actuator push inside arm in see if wheels spin turn frt shaft while holding arm in wheel should turn is they do, replace actuator, if they dont turn then diff problem,

Dec 06, 2009 | 1990 Chevrolet K2500

1 Answer

Where is the sensors for the self leveling option


Sensor should be attached to rear differential housing by a metal and plastic acuator arm and the box and wiring to the body.

Sep 15, 2009 | 2001 GMC Yukon XL

2 Answers

2000 Ford Focus electric locks/acuator failure recurring problem


I would follow their recommendation as I had the same problem with my car. They unhooked the power to that door and it was fine. The problem was a short in the wiring in the door that was causing the problem. So maybe get them to check the wiring in the door as well.

May 20, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...