Question about 2000 Nissan Xterra

Open Question

Heater fuse location for Nissan xterra 2000 - 2000 Nissan Xterra

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
HyeProfile
  • 35 Answers

SOURCE: where is the pcv valve located on a 2000 nissan xterra

Here are the Positive Crankshaft Ventilation maintenance sections of the service manual for both the KA24DE (V4) & VG33E (V6). It doesn't really show where the valve is, but you can figure it out from the pics below. It's on the breather separator.

KA24DE
7927c8a.jpg


VG33E
737cbd7.jpg

Posted on Aug 04, 2009

Ad
ZJLimited
  • 17970 Answers

SOURCE: i am remove heater core from nissan xterra 2000 do

2000-02 Frontier And Xterra

  1. Disconnect both the negative (1st) and positive (2nd) battery cables.
  2. Remove the steering wheel by performing the following procedure:
    1. Turn the ignition switch to the OFF position.
CAUTION Wait 3 minutes after disconnecting the battery cables and turning the ignition switch to the OFF position before servicing the air bag system.
  1. Remove the lower lid and disconnect the driver-s air bag module connector.
  2. Remove both side lids.
  3. Using the Tamper Resistant Torx® Wrench size T50, remove the special bolts from both sides of the steering wheel and discard them.
  4. Remove the SRS module from the steering wheel.

CAUTION Always store the SRS module face up.
  1. Position the steering wheel in the straight-ahead position.
  2. Disconnect the horn connector and remove the steering wheel nut.
  3. Using a steering wheel puller, press the steering wheel from the steering column.
  1. Remove the passenger-s side air bag by disconnecting or removing the following items:
    1. Turn the ignition switch to the OFF position.
CAUTION Wait 3 minutes after disconnecting the battery cables and turning the ignition switch to the OFF position before servicing the air bag system.
  1. Open the glove box door.
  2. Working inside the glove box, open the lower instrument panel lid.
  3. Remove the passenger-s air bag module connector clip from the lid.
  4. Disconnect the passenger-s SRS module connector.
  5. Remove the glove box and the lower passenger-s side instrument panel.
  6. Using the Tamper Resistant Torx® Wrench size T50, remove the SRS module-to-instrument panel special bolts and discard them.
  7. Remove the 4 SRS module-to-instrument panel mounting nuts.
  8. Release the SRS module-to-instrument panel clips and remove the SRS module.
CAUTION Always store the SRS module face up.
  1. Drain the cooling system into a clean container for reuse.
  2. Working inside the engine compartment, disconnect the 2 heater hoses from the heater core.
  3. Discharge and recover the air conditioning system refrigerant.
  4. Disconnect both refrigerant lines from the evaporator core. Plug the lines to prevent moisture from entering the system.
  5. Remove the glove box and the mating trim.
  6. Disconnect the thermal amp connector.
  7. emove the air conditioning housing assembly from the vehicle.
  8. Remove the instrument panel assembly by performing the following procedure:
    1. Remove the 4 steering column cover screws; then, separate and remove the steering column covers.
    2. Remove the 2 driver-s side lower instrument panel screws and the lower instrument panel.
    3. Remove the 4 cluster cover screws and the cluster cover.
    4. Remove the 6 combination meter screws; then, disconnect the combination meter electrical connector and remove the meter.
    5. Remove the 2 glove box screws and the glove box.
    6. Remove the 2 instrument stay cover screws; then, disconnect the electrical harness connectors and remove the stay cover.
    7. Remove the 2 cluster lid -C- screws; then, disconnect the electrical harness connectors and remove the cluster lid -C-.
    8. Remove the 4 audio and deck pocket screws; then, disconnect the electrical harness connectors and remove the audio and deck pocket.
    9. Disconnect the ASCD main switch connector.
    10. Remove the 2 meter cover screws; then, disconnect the electrical harness connectors and remove the meter cover.
    11. Remove the 4 air conditioning-heater control screws; then, disconnect the control cables and remove the air conditioning-heater control.
    12. Remove the front pillar garnish.
    13. Remove the 3 instrument panel assembly nuts and 2 bolts; then, remove the instrument panel.
  9. Remove the heater housing assembly.
  10. Remove the heater core from the heater housing assembly.

continue...

Posted on Jul 16, 2010

  • 1114 Answers

SOURCE: knock sensor 2000 nissan xterra V6, location of

Hello the sensor is located under your intake manifold you will need to remove the intake manifold to gain access to it here is photos of what and where your looking for thisregeetone_0.pngregeetone_21.jpg

Posted on Jan 23, 2011

ameezle
  • 100 Answers

SOURCE: where is the thermostat located

Hi, the thermostat is located in the housing just above the water pump. Follow the top hose on the radiator. There is a metal tubing in the middle of that top hose that leads to the thermostat housing. The housing has 3 screws that attaches it to the engine.

Posted on Jun 11, 2011

mjgebo
  • 11 Answers

SOURCE: Torque and sequence to Intake Manifold for 3.3L Nissan Xterra 2000

#1 is top right most bolt first, 2nd is farthest to the left on top, #3 is the one down and to the left of # 2, #4 is on top and to the left of #1, #5 is the hardest one to get to and is right in the middle on the bottom, and #6 is only one left which is top middle....
on re-installation you go backwards and torque from 2--22 NM

Posted on Mar 09, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater and ac blower not working nissan xterra


Have you checked your fuses? Most vehicles have a fuse for the blower. It could be as simple as a blown fuse. If the fuse for the blower is not blown, there's a possibility that the actual motor could have gone out. Thanks.

Jun 02, 2016 | 2000 Nissan Xterra

1 Answer

Where is the egr located for a 2000 nissan


Here's a link,it tells you where it;s at,but now you know what it look's like and can see it easy. Duralast EGR Valve EGR4170 2000 Nissan Datsun Xterra 2WD 4 Cylinders 2...

Oct 17, 2014 | 2000 Nissan Xterra

2 Answers

No heat 2002 Nissan Xterra


Check to make sure the radiator is full and the heater hoses are getting hot. If so, you may have a problem with the blend door under the dash.

Sep 25, 2012 | 2000 Nissan Xterra

1 Answer

2000 nissan xterra, replaced washer pump, not pushing any fluid, is there a fuse for the washer if so i havent been able to find it.


have someone press washer switch and feel if pump is working if not the owners manual will have fuse location and breakdown of circuits it uses check that hope it helps you

Jan 15, 2011 | 2000 Nissan Xterra

2 Answers

The power outlets dont work in my 2000 Nissan


Check fuses located at driver's left dash area and under the hood.

Feb 09, 2010 | 2000 Nissan Xterra

1 Answer

Where is the knock sensor for the 04 nissan xterra located?


Your knock sensor is located undernesth the air intake manifold on top of the engine block. This goes for 2000-2004 xterra V6 3.3L models.

Nov 05, 2009 | 2002 Nissan Xterra

1 Answer

2000 Nissan Xterra Service Engine soon indicator is always on


The knock sensor is not a huge deal to replace and will not turn on the light. It should be dont though.

The crankshaft sensor is located directly between the engine and transmission. It is dead center at the bottom.

May 17, 2009 | 2000 Nissan Xterra

1 Answer

2000 Xterra Brake Lights


Check the brake light switch located near the brake petal.

Nov 16, 2008 | 2000 Nissan Xterra

Not finding what you are looking for?
2000 Nissan Xterra Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...