Question about Cars & Trucks

1 Answer

Can i remove the catalytic converters on my touareg v10 2007 model

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,428 Answers

Physically yes you can but the vehicle would be illegally modified and will not pass an emmissions test!

Posted on Dec 19, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2003 chevy impala just loses power while driving, it seems like its choking for a while then regains power again and runs normal


have car checked for a plugged catalytic converter by a reputable technician. A clogged catalytic converter results in a loss of power. The catalytic converter is made of an aluminum oxide honeycomb coated with platinum and palladium. These components react to remove CO and HC's from the exhaust stream. A two-way catalytic converter works by oxidizing CO (carbon monoxide) and HC (hydrocarbons "unburned fuel") to CO2 (carbon dioxide) and water. A three-way catalytic converter also removes NOx (oxides of nitrogen) from the exhaust. NOx is formed at high cylinder temperatures. The EGR system is responsible for inhibiting NOx. Signs of clogged bad catalytic converter

Jan 17, 2016 | Cars & Trucks

1 Answer

2000 S80 2.9 Is the connection where the exhaust and catalytic converter meet threaded on both the exhaust and the catalytic converter, or does the bolt just go through both and have a nut on the end? ...


SPRAY PENETRATING OIL LET IT SOAK 30 MINUTES THEN REMOVE BOLTS .THE BOLTS GO THROUGH CATALYTIC NUTS HOLDING ON THE OTHER SIDE.THE OTHER SIDE CATALYTIC CONVERTER HAS CLAMPS HOLDING IN PLACE OR IT COULD BE SPOT WELD IN PLACE THE CATALYTIC CONVERTER MAY OR MAY NOT PULL AWAY FREE I HAD TO GO TO MUFFLER SHOP SOME TIMES THEY HAD TO CUT THE WELD SPOTS SEAL EXHAUST PIPE TO THE CATALYTIC CONVERTER.

Oct 30, 2011 | 2000 Volvo S80

1 Answer

What are the torque specs for 1996 Buick Century 3.1 L intake manifold?


Front Pipe REMOVAL & INSTALLATION Pipe Without Catalytic Converter
  1. Before removing any component of the exhaust system, always squirt a liquid rust dissolving agent onto the fasteners for ease of removal..
  2. Raise and support the front of the vehicle on jackstands.
  3. Remove the exhaust pipe-to-manifold nuts.
  4. Support the catalytic converter, then disconnect the pipe from the converter. Remove the pipe.
  5. Remove the exhaust gaskets. To install:
  6. Be sure to use all new gaskets when required. Assemble the system, check the clearance and tighten the bolts to about 15-30 ft. lbs. (20-41 Nm). Fig. 1: Front exhaust pipe connection common on vehicles with the catalytic converter not included 86813320.gif

  7. All clamps should be tightened to about 18-25 ft. lbs. (24-34 Nm). Do overtighten the clamps. If pipes become dented they can leak.
Pipe With Catalytic Converter
  1. Before removing any component of the exhaust system, always squirt a liquid rust dissolving agent onto the fasteners for ease of removal.
  2. Raise and support the vehicle.
  3. On some vehicles you will need to remove the brace from the transaxle.
  4. Remove the exhaust pipe nuts from the manifold.
  5. Support the catalytic converter pipe bolts from the rear of the converter.
  6. Lower the catalytic converter/front pipe assembly from the vehicle. To install:
  7. Be sure to use all new gaskets when required.
  8. Attach the new catalytic converter/front pipe assembly to the vehicle. Tighten the pipe to manifold nuts to 20-40 ft. lbs. (27-55 Nm).
  9. Attach the bolts at the rear of the catalytic converter/front pipe. Tighten them to 30-35 ft. lbs. (41-47 Nm).
  10. Connect the brace at the transaxle if removed.
  11. Lower the vehicle. prev.gif next.gif

Dec 18, 2010 | Buick Century Cars & Trucks

1 Answer

How do you know if your cat converter is going bad? Can you test for it?


There are two ways a converter can fail:
  • It can become clogged.
  • It can become poisoned.
There really is no "inspection port" for the consumer or mechanic to see an actual clog in a converter. Often, the only way to tell if a catalytic converter is malfunctioning (plugged) is to remove it and check the change in engine performance. When a clogged converter is suspected, some mechanics temporarily remove the O2 sensor from the exhaust pipe ahead of the catalytic converter and look for a change in performance.
A catalytic converter relies on receiving the proper mix of exhaust gases at the proper temperature. Any additives or malfunctions that cause the mixture or the temperature of the exhaust gases to change reduce the effectiveness and life of the catalytic converter. Leaded gasoline and the over-use of certain fuel additives can shorten the life of a catalytic converter.
A catalytic converter can also fail because of:
  • Bad exhaust valves on the engine
  • Fouled plugs causing unburned fuel to overheat the converter
­Sometimes you can tell that a converter is clogged because you don't go any faster when you push the gas pedal. Also, there usually is a noticeable drop in gas mileage associated with a clogged catalytic converter. A partially clogged converter often acts like an engine governor, limiting the actual RPMs to a fast idle. A totally clogged converter causes the engine to quit after a few minutes because of all the increased exhaust back pressure.
The catalytic converter, like the rest of the emissions system, typically has a warranty length that exceeds the term of the warranty for the rest of a typical U.S. automobile.
Here is a safety reminder: Do not park your car over tall grass or piles of dry leaves. Your car's perfectly running catalytic converter gets very hot -- enough to start fires! You can keep it running well by keeping the ignition system in top shape, to prevent any unburnt fuel from entering the catalytic converter.

Dec 11, 2010 | 1989 Dodge Dakota 2WD

2 Answers

I have an 1998 Chevy Blazer and need to change the catalytic converter, are the flange bolts welded and can i cut them


Catalytic Converter Removal & Installation 2.2L Engine To Remove:
Catalytic converter 2.2L engine gm-03-22-734.gif

  1. Raise and safely support the vehicle.
  2. Disconnect the heated oxygen sensor (HO2S) electrical connector.
  3. Remove the exhaust manifold pipe flange mounting nuts from the catalytic converter.
  4. Remove the catalytic converter flange mounting nuts from the muffler.
  5. Remove the catalytic converter from the muffler.
  6. Remove the catalytic converter from the rear hanger bracket insulator.
  7. Remove the catalytic converter.
  8. Remove the (HO2S) from the catalytic converter.
To Install:
  1. Install the (HO2S) to the catalytic converter.
  2. Install a new gasket and the catalytic converter to the muffler.
  3. Install catalytic converter to the catalytic converter hanger.
  4. Install the catalytic converter flange mounting nuts to the muffler flange.
    • Tighten to 26 ft lbs (35 Nm).
  5. Install the catalytic converter flange mounting nuts to the exhaust manifold pipe flange.
    • Tighten to 26 ft lbs (35 Nm).
  6. Connect the heated oxygen sensor (HO2S) electrical connector.
  7. Lower the vehicle.
------ Catalytic Converter Removal & Installation 4.3L Engine To Remove:
  1. Raise and safely support the vehicle.
  2. Raise and support the transmission.
  3. Remove the transmission support
  4. Disconnect the left and right pre-converter heated oxygen sensor (HO2S) electrical connector.
  5. Disconnect the post-converter (HO2S) connector. Muffler flange and gasket gm-03-43-731.gif

  6. Remove the catalytic converter flange mounting nuts from the muffler.
  7. Remove the catalytic converter from the muffler.
  8. Remove the exhaust manifold flange mounting nuts from the catalytic converter. Catalytic converter 4.3L engine gm-03-43-735.gif

  9. Remove the catalytic converter from the support bracket insulator.
  10. Remove the catalytic converter and gaskets.
  11. Remove the heated oxygen sensor.
To Install:
  1. Install the heated oxygen sensors as needed.
  2. Install a new gasket and the Install the catalytic converter to the support bracket insulator.
  3. Install the catalytic converter to the exhaust manifold flange. Install the mounting nuts.
    • Tighten to 39 ft lbs (53 Nm).
  4. Using a new flange gasket, install the catalytic converter to the muffler. Install the mounting nuts.
    • Tighten to 30 ft lbs (40 Nm).
  5. Connect the left and right pre-converter heated oxygen sensor (HO2S) electrical connectors.
  6. Connect the post-converter (HO2S) electrical connector.
  7. Install the transmission support.
  8. Lower the transmission.
  9. Lower the vehicle.
prev.gif next.gif ---
It looks like you can cut them and replace them with new bolts and nuts.prev.gif next.gif

Sep 05, 2010 | 1998 Chevrolet Blazer

1 Answer

Coils need to be replaced and VW Touareg Catalytic Converter


Call around find out. Call at least 3 repair shops to get an estimate.

Mar 31, 2010 | 2004 Volkswagen Touareg

1 Answer

How to replace/remove both catalytic converters


Below are the steps needed to remove the catalytic converters. You may be able to first remove the band clamp from between the converter and the exhaust manifold, then loosen the rest of the system and to get enough clearance to slide the converter towards the front of the vehicle but you will need to first remove the clamp that holds the converter to the rest of the exhaust. Hope this helps
_______________________
Both Catalytic Convertors

First you need to raise the vehicle.

Next, you need to pry the insulators from the support brackets and support the muffler and tailpipe with jackstands.

Then, loosen the the catalytic converter down pipe-to-front resonator clamps and separate the front resonator from the converter down-pipes. Carefully lay the free laying exhaust on the ground.

______________________
Right Catalytic Converter

Then, remove the down-pipe-to-transaxle bracket nut, loosen the clamp and separate the extension pipe from the converter.

Next lower the vehicle and remove the air filter and intake ducts. Disconnect the wiring harness for the O2 sensor and the remove the sensor.

Finally loosen the band clamp at the exhaust manifold and remove the converter from the engine compartment. You may need to replace these clamps after removal because you need to pry it apart and they will leak when you reinstall.

_____________________
Left Catalytic Converter

Now disconnect the wiring harness for the O2 sensor and the remove the sensor.

Next remove the down-pipe-to-transaxle bracket nut

Finally loosen the band clamp at the exhaust manifold and remove the converter from the engine compartment.

Apr 22, 2009 | 1999 Dodge Intrepid

1 Answer

Catalytic converter


HI, this guide will help you with this replacement.

Step1 Lift your jeep. Unfortunately, the catalytic convertermag-glass_10x10.gif sits about midway down the length of your jeep, so lifting one end or the other will not do. Ramps are your best bet to get you within reach of the parts when working from home. Luckily, this is usually the hardest part of this repair. Step2 Be patient with the bolts, as they are often hard to remove due to size and awkward placement. You may have to drill or saw bolts to remove them. With this in mind, you should pick up new bolts, nuts and seals for your replacement project. Step3 Buy a catalytic converter specific to your jeep to avoid extra work. A generic part must be welded into the jeep, while a vehicle-specific model comes pre-welded to the proper pipes for easy bolt-on installation. Step4 Remove the 02 sensor (with an O2 wrench) before unbolting the catalytic converter. Then, you should remove the pipe connecting the sensor to the converter. Depending on your exhaust system, you may have to remove more pipes before you unbolt the converter from the muffler. Step5 Replace the old catalytic converter with a new one. This should be the easy part, as you simply bolt the new part in place. Step6 Reattach the exhaust pipesmag-glass_10x10.gif and 02 sensor, and the basic job is done. Make sure you replace any cracked or rusty pipes while you have the exhaust system apart.

  • Catalytic converters often fall under a separate emissions warranty that lasts at least 7 years and 160,000 miles. Even if your car is out of its regular warranty, but it is a newer model, ask your dealer to replace the part for you free of charge.
  • Rent the O2 wrench or socket if you do not own one. Most auto parts stores carry this tool for rentals.
  • In many states, older (vintage) cars do not need a catalytic converter, so you can gut it or remove it completely. No damage will result from running a car without a converter.
  • Due to emissions standards, it is illegal to buy or install used converters.
Please rate and god bless:)

Apr 20, 2009 | 1998 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...