Question about Cars & Trucks
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Replace the Resistor located near the blower motor.Under the dash. It may be a little hard to get to. it has a plug of four wires and a couple of screws you have to remove. The reason your other problems are happening is because you disconnect the battery and the Computer (ECU) deprograms itself .
Posted on Jan 22, 2009
First check if the wires are still on the starter and tight. Then ..
While someone tries to turning the key tap on the starter body with a rod or bar, if this causes the starter to try and engage you have a bad starter.
Hope this helps.
Posted on May 11, 2009
Could be the starter..
( at the same time when turning the key to start )
give the starter a few whacks with a small hammer..
Takes 2 people..
If it turns - or turns slow - let me know..
Posted on Jul 09, 2009
You could have a start that has gone bad and will need to be replace,or your having a Passlock system problem.
Your Passlock may need to relearn the ignition keys, if the ignition lock has gone bad like my in-laws Grand Am Gt, here is what i did so they will not get stranded any more. Buy a Passlock by pass module for around $70.00. You can orderone from GMPASSLOCK.COM in the mean time try resetting the Passlock. Good luck
Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure
1.) Turn ON the ignition, with the engine OFF.
2.) Attempt to start the engine, then release the key to ON; the vehicle will not start.
3.) Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF.
4.) Turn OFF the ignition switch, and wait 5 seconds.
5.) Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes.
The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
6.) Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.
7.) With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles.
Without a scan tool you may have momentary starter interruptions while history clears itself.
Posted on Jan 12, 2010
Tips for a great answer:
Feb 05, 2016 | 2001 Buick LeSabre
Mar 23, 2012 | 1999 Plymouth Grand Voyager
Mar 24, 2011 | 2006 Toyota 4Runner
Feb 23, 2011 | 2001 Mitsubishi Montero
Jan 18, 2011 | Plymouth Voyager Cars & Trucks
Mar 31, 2010 | 2000 Oldsmobile Intrigue
Feb 05, 2010 | 1998 Mitsubishi Eclipse
Nov 29, 2009 | 2001 Daewoo Lanos
Oct 29, 2009 | 1991 Honda Accord
Jun 28, 2009 | 2003 Jeep Wrangler
Nov 19, 2017 | Suzuki Cars & Trucks
16 people viewed this question
Usually answered in minutes!