Question about Cars & Trucks

Open Question

I Any idea how to remove the insert from the Hubbell Taymac weatherproof cover without breaking it

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant figure out how to remove key cylender from a 99 honda civic


TURN OFF RADIO.DISCONNECT NEGATIVE BATTERY CABLE.WAIT 20 MINUTES FOR AIRBAGS TO DISCHARGE.YOU NEED TO REMOVE THE STEERING COLUMN COVERS AND LOWER INSTRUMENT PANEL COVER.REMOVE THE IGNITION SWITCH.REMOVE THE RETAINING NUTS AND LOWER THE STEERING COLUMN.THE LOCK ASSEMBLY IS CLAMPED BY TWO SHEAR HEAD BOLTS.USE A CENTER PUNCH TO MAKE A DIMPLE IN THE HEAD OF EACH BOLT,THEN DRILL THE HEAD OFF WITH A 3/16 INCH DRILL BIT.SEPARATE THE CLAMP AND REMOVE THE ASSEMBLY FROM THE STEERING COLUMN. PLACE THE NEW LOCK ASSEMBLY IN POSITION WITHOUT THE KEY INSERTED AND TIGHTEN THE BOLTS UNTIL THEY ARE SNUG.INSERT THE KEY AND CHECK THE LOCK CYLINDER FOR PROPER OPERATION. TIGHTEN THE BOLTS UNTIL THEIR HEADS BREAK OFF.TIGHTEN STEERING COLUMN TO INSTRUMENT PANEL FLANGE NUTS TO 108 INCH POUNDS.TIGHTEN THE RETAINING COLLAR CLAMP BOLTS TO 16 FT LBS.

Apr 29, 2011 | Honda Civic Cars & Trucks

1 Answer

I have a 1988 f-350 diesel and i have lost my key and bought it without a spare how do i remove the ingnition with out a key


You don't without ruining it. I suggest you get a locksmith to make you a new key they can get in there somehow and make a key. In 1988 did Ford use a seperate key for doors? If the doors are the same or the glove box those locks are easier to remove. Also, I've never tried this with a Ford but on newer GM cars if you take the title to a dealer they can make a key from the (VIN) serial number. But, you have to have the title to prove ownership of the vehicle. I don't know if they can do that on an 88 or not. Good luck.

Feb 09, 2010 | 1988 Ford F 350

1 Answer

The interior dome light is burned out, removing cover problem.


You will have to pry off the lens CAREFULLY using a small screwdriver. There are two little plastic protrusions on each long side of the lens which fit into the casement. You can ease the casement away from the lens enough to get it to pop out. Re-inserting it is the same, but probably easier.
Gently, give it a try.
Hope this helps you.

Oct 23, 2009 | 1994 Honda Accord

1 Answer

Do i have to remove the door panel to take off door speaker covers? Speaker covers are starting to rust and want to remove all 4 speaker covers on door just to paint them. Trying to remopve without...


I believe that your speaker covers are clipped in through the back of the panel and won't come out through the front without breaking some of the clips. The proper way would be to remove the door panels and remove the covers out the back of the panel.

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can remove the panel

Sep 24, 2009 | 2002 Lincoln LS

1 Answer

The drivers door lock will only lock the doors and


Try removing the switch the door panel, then removing the cover from the switch. Once the cover is off the switch and the contacts are exposed, check them for breaking....if all looks good, spray the contacts with an electrical cleaner.

Jun 29, 2009 | 2000 Ford Explorer

1 Answer

My driver side door handle is broken on a 2003 VW new beetle. How can I fix it?


remove the inside door trim and remove the weatherproof plastic that covers the holes in the door behind the trim.
You should have access to the door handle nuts and rods to remove the handle.
re assemble in the reverse order and make sure the weatherproof plastic is put back on and sealed or your door may let water enter the car via the door

May 12, 2009 | 2000 Volkswagen Passat 4Motion

1 Answer

Need to remove 2000 Avalon CD player


yes there is a screw inside the vent flaps

Mar 15, 2009 | 2000 Toyota Avalon

2 Answers

Need to replace cargo & third break light how do i


if its the same as an 06 Tundra, you should be able to remove the lense cover from the back of your truck cab with a screwdriver and pull the light bulbs out...Do not remove the screws below the lense cover that removes the fixture, they have a screw insert that will fall into your truck's body and get lost.....hehehehe I learned that from my own experience...good luck!

Mar 04, 2009 | 2008 Toyota Tundra

1 Answer

Need to change interior lights


Very easy to remove: You insert a small flat blade screwdriver into the small slot, an pry it open. The plastic is rather strong; if you pry on the center of the slot, it will not break. Hope this helps.

Nov 02, 2008 | 2000 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...