Question about 2005 Chrysler Town & Country

Open Question

Blend doors 2005 Chrysler town and country not working, stuck on cold output

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: door locks

Daughter had same problem on '05 T&C. Neighborhood mechanic searched Internet and found 80-90 others with same problem right around 40,000 miles. Free solution was to pull yellow 20A IOD fuse in right front corner of fuse box under hood, wait 10 seconds, then reinsert fuse. Should solve problem as long as you don't lock doors with FOB. You can unlock doors with FOB, but apparently locking with FOB causes the problem.

Permanent solution is to have dealer reprogram computer for around $50 which is what my daughter chose to do because of inconvenience of not being able to lock doors with FOB when getting baby/carseat out of vehicle.

Posted on Dec 07, 2008

Ad
chryslertech
  • 115 Answers

SOURCE: low speed fan relay for the 2005 chrysler town and country

If you are talking about the cooling fan relay for the radiator there is no low speed and high speed relay. There is only one relay and it is behind the grill revitted to the bumper rail. It is doesnt look like you typical relay.

Posted on Mar 08, 2009

alicantecoli
  • 22265 Answers

SOURCE: Chrysler trouble code U110C on 2005 chrysler town

encrypted software ,dealer only----yes i know you are showing a reading but it doesnt mean anything or if it does it shows a different code .so your snap on or mac tools scanner is a waste of time and money.Nearly all new motors from 2005 are using encrypted software to stop general mechanics like me from working

Posted on Sep 12, 2009

  • 79 Answers

SOURCE: power door locks on 2005 chrysler town and

There is an ecu flash for this repair. You may get the locks to start working again with a battery disconnect.

Posted on Jun 18, 2010

  • 17 Answers

SOURCE: 2005 Chrysler Town & Country. Passenger side window problem.

HAVEK 1005 sounds right on track.... but also try this, usually works well for non functional power windows, specially Caravans.

NO COST PROCEDURE TO FIX IT:

1. Sit in vehicle, on seat next to problematic window
2. Ignition key is on
3. Door in question is opened (in case you closed it)
4. While door is open, press and hold power window button in desired window travel, keep button pressed !!
5. SLAM hard the door closed with one hand while other hand holds button as per #4.
6. Watch window operate as it should.
7. Repeat 3-6 if necessary, but usually the first try works!

NOW, for the naysayers that says you must replace power window motors etc, at $$$ cost because the above fix does not work, or is not long lasting fix, or less than a "professional fix".... Well then, when the window fails to operate again, apply same fix again at that time.

I have fixed my van this way numerous times (usually once a year), and to all local friends I recommend this fix too, likewise do the same and are happy with the solution.

Posted on Jul 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chrysler town&country heater blows cold air all the time


Blend door between heater duct, and evaporater core is stuck, or heat/A/C control on the dash could be bad.

Mar 08, 2013 | 2007 Chrysler Town & Country LX New Cars

1 Answer

2005 chrysler town & counry constantly blows hot in front


I'd lean more toward the blend door actuator. I've experienced that problem more often with Grand Caravans (aka Town and Countries) and Pacificas. Usually, if it's a resistor, it's the blower motor resister, which means you wouldn't get any air movement at all.

The only thing I can't recall off hand is if Chrysler services the actuator separate from the blend door housing on these models. However, I'm sure that's what you will need as the blend door is what regulates the mixture of cool and hot air. Keep in mind this is not the mode door actuator or housing. That's something completely different that directs the air to different paths (vent, floor defroster, etc.)

Contact Chrysler as I believe these are only available OEM last I checked.

Aug 23, 2012 | 2005 Chrysler Town & Country

1 Answer

2007 chrysler town and country a/c blows cold through floor and defrost vent but not dash vents


Often a sign of a blend door problem. The blend door or doors are in the heater a/c box behind the dash.

Jun 28, 2012 | Chrysler Town & Country Cars & Trucks

1 Answer

A/c not blowing cold air on 2002 toyota camry


low on freon, faulty relay, faulty low pressure switch, faulty compressor and/or clutch, blend door stuck or not cutting off heat

Jun 27, 2012 | 2002 Chrysler Town & Country

2 Answers

My wifes minivan, 2001 chrysler town and country does not blow very cold air. it's cool but not cold. I have replaced the dryer and recharged system to 2.69lbs. It holds vacuum and the guages are in...


Did you pull a vacuum on the system before charging? Disconnect the blend door actuator and turn it by hand. These aren't known for having stuck blend doors.

Jul 12, 2017 | 2001 Chrysler Town & Country

1 Answer

My 2001 Chrysler Town and Country heater is working fine on the driver side, but blows out cold air on the passenger side. Help


I have seen this quite a bit. This issue is caused by the blend door for the climate control system. Those doors were not that well constructed and end up breaking to the point where the climate system can no longer operate the door. This can be a very difficult to repair because it requires dash removal to get access to the appropriate door. This condition can easily be verified by a dealer test with scan tool. If you would like to replace yourself I would recommend contacting dealer for a copy of the removal and repalcement procedure for the passengers blend door. I hope this information was helpful.

Feb 22, 2011 | 2001 Chrysler Town & Country

1 Answer

My heat stopped working in my 2000 town and country van and I have no idea why...any suggestions? Thanks In wi and it's freezing


If it happened suddenly, it is probably the blend door actuator.

Please see my tip at http://www.fixya.com/cars/r6235876-no_heat_fan_blowing_cold_air . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Your blend door actuator is above the accelerator pedal. See picture below.
jturcotte_517.gif

Dec 15, 2010 | 2000 Chrysler Town & Country

1 Answer

A/c doesn't work, heater runs on high without command,sometimes unable to shut-off


You need to check your blend door. It sounds like its stuck on heat. Your blend door would be the switch that changes from hot to cold.

May 08, 2009 | 2005 Chrysler Town & Country

1 Answer

Heat on, blows cold air on passenger side


u will need to repair the passenger side air temp control blend door, either the door is stuck or the small electric actuator that moves it is defective.

Jan 14, 2009 | 2004 Chrysler Town & Country

Not finding what you are looking for?
2005 Chrysler Town & Country Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...