Question about Cars & Trucks

Open Question

Econovan maxi 1993 repair manual - Cars & Trucks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
HansPP
  • 2510 Answers

SOURCE: van barley moves in reverse

It could be a myriad of things, start off by checking the transmission oil level and also look if it is black This would signify that the valve passages could be clogged or that there is something further amiss in the transmission.

Posted on Jan 30, 2011

Ad
  • 161 Answers

SOURCE: Unidentified hose. I have a Ford Econovan, which

2nd hose is for you positive crankcase ventilation(PCV) valve hose....(like a breather hose)

Posted on Mar 20, 2011

Testimonial: "Called the service center and read the Haynes manual, they both say the same thing. Spot on!"

  • 5341 Answers

SOURCE: How to replace clutch master cylinder Ford Econovan Maxi 1993 without pulling the entire dash out?

Wait. Maybe you're in the wrong place. All cars I have seen have the clutch master cylinder bolted to the firewall inside the engine compartment. You take off the line going to the clutch, remove two bolts or nuts holding the unit to the firewall; and remove the unit. The only thing maybe to remove under the dash is the pushrod from the clutch pedal to the master cylinder.
Now if yours is different, then proceed, but check under the hood for the clutch master cylinder first.

Posted on Nov 02, 2012

  • 83 Answers

SOURCE: FORD ECONOVAN MAXi 2.0 Hi, i have a serious creaking and groaning noise from the front nearside when I hit a bump or speed hump could I need a new shock absorber? I dont get the bump I would expect

It could be your shock/strut for sure. It could also be other suspension parts like the control arm or ball joints but I would suspect shocks first. If you arent extremely proficient, I would leave this repair to the pros. It isnt hard but it is incredibly dangerous. To get the old shock off you need to compress the spring with a special tool, and once it is compressed, it is like a bomb waiting to go off and could easily kill you. Take it to a shop and have them confirm the problem then do the repair. It should be around 150 for the part ( or less!) and another 100 for the labor.

Posted on Jul 10, 2014

  • 44530 Answers

SOURCE: I have a 1993 ford Econovan maxi . I have ignition point . What is the gap on the ignition point . Thanks

point gap is .40 to .50 mm ( point 4 to point 5 mm) or .015 to .20"
most point distributors are at the .02 " mark but check and adjust as points to wide will misfire under load or lack power if too close
point gap variations can change ignition timing

Posted on Nov 20, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 1993 ford econovan maxi engine is missing - what is the likely cause?


missing check the spark plugs is the first thing to look at. check the color of them, if any of them are wet or if one is not the same color as the rest. check these first.

Jun 15, 2017 | Ford Cars & Trucks

1 Answer

I have a 1993 ford Econovan maxi . I have ignition point . What is the gap on the ignition point . Thanks


point gap is .40 to .50 mm ( point 4 to point 5 mm) or .015 to .20"
most point distributors are at the .02 " mark but check and adjust as points to wide will misfire under load or lack power if too close
point gap variations can change ignition timing

Nov 20, 2016 | Ford Cars & Trucks

2 Answers

I need a manual for a 1992 ford econovan


different rear axles fitted to an econovan
depending on all up weight ?

cant find a cd version on offer or reliable free downloads in pdfs
lots of printed repair manuals for sale on ebay


tapered or a full bearing best way is
the bearing will need to be pressed off and pressed back on

tapered
you can cold chisel off the holding ring and use tube method
but that ring must be holding to pressed specs
other wise the axle can sheer holding nuts and will fall off and away while driving



26337118-qjqnzydliaqyqu4sjtgj0otb-1-0.gif


this axle is stuck fast
26337118-qjqnzydliaqyqu4sjtgj0otb-1-6.jpg

26337118-qjqnzydliaqyqu4sjtgj0otb-1-3_0.jpg

Nov 02, 2016 | Ford Cars & Trucks

1 Answer

How much water goes into the cooling system of a ford econovan maxi 1995


depending on which engine you have ,you are looking at 12 to 16 litres when empty

Feb 23, 2015 | Ford Cars & Trucks

1 Answer

FORD ECONOVAN MAXi 2.0 Hi, i have a serious creaking and groaning noise from the front nearside when I hit a bump or speed hump could I need a new shock absorber? I dont get the bump I would expect


It could be your shock/strut for sure. It could also be other suspension parts like the control arm or ball joints but I would suspect shocks first. If you arent extremely proficient, I would leave this repair to the pros. It isnt hard but it is incredibly dangerous. To get the old shock off you need to compress the spring with a special tool, and once it is compressed, it is like a bomb waiting to go off and could easily kill you. Take it to a shop and have them confirm the problem then do the repair. It should be around 150 for the part ( or less!) and another 100 for the labor.

Jul 10, 2014 | 1992 Ford Econoline

1 Answer

How to replace clutch master cylinder Ford Econovan Maxi 1993 without pulling the entire dash out?


Wait. Maybe you're in the wrong place. All cars I have seen have the clutch master cylinder bolted to the firewall inside the engine compartment. You take off the line going to the clutch, remove two bolts or nuts holding the unit to the firewall; and remove the unit. The only thing maybe to remove under the dash is the pushrod from the clutch pedal to the master cylinder.
Now if yours is different, then proceed, but check under the hood for the clutch master cylinder first.

Nov 02, 2012 | Cars & Trucks

2 Answers

Valve clearances for a ford econovan 1.8lt, 1990


what are the valve clearance specs for a 1990 ford econovan maxi

Mar 14, 2010 | 1989 Ford Econoline

1 Answer

Where is the clutch fluid reservoir


if it's a hydralic clutch, then it's shared

May 30, 2009 | 1996 Ford Econoline

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...