Question about Cars & Trucks

Open Question

I've got an 03 600 edge and have coolant leaking out of one of the head cover bolts. Is this a blown head gasket? Still runs OK, is there a chance I damaged the engine though?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mrgreenz
  • 962 Answers

SOURCE: 1996 honda prelude oil leak

did you check the steering pump, AC compression pump, etc or other engine components ? it could be something other than the engine.

Posted on Nov 18, 2008

Ad
  • 35 Answers

SOURCE: coolant leak

That would be a head gasket leak. The motor will run fine there min. change white smoke from exhaust but min. On newer cars the check engine light will engage

The problem is that your oil and anti freeze are mixing not a good thing. Good luck .

Posted on Feb 13, 2009

  • 42 Answers

SOURCE: Coolant leak on 2001 Taurus.Coolant seems to be

heaterhose is in that general area. most common leak is that spraying aroung so it looks like something worse

Posted on Mar 17, 2009

  • 316 Answers

SOURCE: Coolant overflowing out of expansion tank no boil no steam

As you've stated driving around town it's fine, and everything is working well. For the symptoms, there are 2 possible causes:
1. Your cooling fans are not working.
2. Your radiator needs to be replaced.
I'm sure you can determine which it is, and I wish you luck on your repair.

Posted on Jun 02, 2009

  • 1 Answer

SOURCE: Head gasket is damaged. 2005 Nissan Sentra, 1.8

i have a 2005 1.8 nissan sentra.i rplaced the radiator becuause it was leaking.so when i did i took it for a test drive and the needle went to hot then back down to middle ways between the C & H BACK IN FORTH.so i replaced the thermostat. now as far as i can tell it is staying in the middle of C & H. i can't feel no water though cerulating through the top or bottom hose of the radiator. so now that i told you what i done so far my question is???? ( my heater is not working in the car it is blowing out cold air & i left the car runnng for about 45 min. even took it up and down the road.still cold air.what do you think i need to do?????????? )

Posted on Jan 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I had my intake manifold gasket change along with the valve cover gasket. White smoke is still coming out of tailpipe?


White smoke may indicate an internal coolant leak or low coolant reservoir levels. Coolant leaks can also leak into the oil of your car causing it to be frothy or milky looking smoke. You might have a cracked head gasket, engine block, or cylinder head which are all caused by overheating.

Dec 17, 2015 | Cars & Trucks

1 Answer

Replacing a head gasket in a 1993 buick century


Before head gasket replacement have you checked these
Intake Manifold Gaskets May Leak Coolant or Engine Oil
engine or leak. In some cases, an internal coolant leak may occur causing coolant to mix with the engine oil. Our technicians tell us that operating the engine with a coolant/oil mix can result in internal engine damage. Replacing the intake manifold gasket should correct these leaks.
Leaking Water Pump May Cause Coolant Loss and Overheating
A coolant leak may develop from the . The may overheat as a result of the coolant loss. A leaking water pump should be replaced.
Headgasket replacement
step 1. undo negative battery cable or completely remove battery and tray.
step 2. remove air cleaner and associated piping if it is in the way to allow access to head, drain cooling system and remove upper radiator hose.
step 3. remove top portion of exhaust manifold.
step 4. remove intake manifold and fuel injection rail as necessary
step 5. remove spark wires and valve cover.
step 6. remove drive belts and top timing cover before removing timing belt find all alignment marks and paint to improve your visibility and aid in reassembly if no marks are present remove spark plug # 1 and rotate until piston is at tdc and check timing mark on crankshaft that it is on 0 then paint the belt and cams anything that has teeth that the timing belt rides on make a mark to aid in reassembly even if you are replacing t-belt at least you can compare to new belt and transfer marks, release tension on t-belt tensioner and remove t-belt.
step 7. remove head bolts start loosening at inside and work outwards reemove head bolts and pay attention to sizing and placement.
carefully check for anything that is still attached to head and if free tap head with rubber or dead blow hammer to free from block and lift straight up so as not to ruin or bend any of the alignment pegs.
step 8. remove head gasket material with non-scratching tools or scrapers or buff pads made for that job. making note of where it was blown.
step 9. decide if you should send head to machine shop to have mating surface made flat again and also to have valves and related parts inspected or replaced. usually about $300-$400
step 10. inspect block remove all gasket material look for pitting or scarring also use straight edge to determine if it is straight or if it needs to be resurfaced by a machine shop.
step 11. install new headgasket and check fit. If all is good reassemble in reverse order of removal and I always like to replace crank seal ,cam seal, water pump, t-belt and tensioner also thermostat, drivebelts, spark plugs, cap, rotor, wires, pcv valve, intake manifold ,exhaust manifold gaskets.
this is just a broad overview hope it helps you will have to get haynes manual or similar for head torque values and what not

Aug 05, 2014 | 1993 Buick Century

3 Answers

Dumping coolant out of the exhaust pipe


  • coolant from exhaust indicates a blown head gasket or a cracked head on the block

May 13, 2014 | Chevrolet Cavalier Cars & Trucks

1 Answer

1994 honda delsol overheating


check your oil and see if your getting coolant in it.. if u take the oil fill cap off and look inside the valve cover.. if it looks like coffee u probably have a blown head gasket.. also check the coolant and see if it is low or looks like oil is getting into it... also if your coolant has ever got low/ leaked out..u may have a air pocket inside the engine.. but if i know my hondas like i think i do... chances are u got a blown head gasket... if u dont notice the coolant in the oil right away dont worry if u keep driving it with these symptoms u will soon enough...

Dec 05, 2012 | Cars & Trucks

3 Answers

Leaking coolant.. its hard to see where it is coming from.. it leaks out heavily when car is cranked,, it looks like it is comin from right behind the belt drive (the bigger one) is that the water pump?


This does sound like your water pump is leaking, or your head gasket has busted on the outside edge. I would check the water pump first, as it is fairly common for the seal to bust and leak coolant from the water pump.

Feb 16, 2011 | 2004 Pontiac Grand Prix

2 Answers

Oil in the coolant dept not a lot but oil is in there what can be the problem


U have a leaking engine cylinder head gasket, very common on this van.

Sep 03, 2010 | 1999 Ford Windstar

3 Answers

Overheating, milky oil, oil in coolant...Please help!


Well, the good news is this could be something as simple as a blown head gasket. The bad news is most likely that is not the case. You have either cracked your block, cracked the head, worn a hole in your timing chain cover that is allowing the water and oil to mix or blown your head gasket or a combination of these problems. Your choices are to pull everything apart and magna Flux the Engine block and heads or replace the motor, assuming the issue isn't a hole worn in the timing chain cover, or replacing the motor, the easiest of the solutions although not the cheapest. A decent short block should run around $600 to $1000 with shipping. It's used but has been checked and should serve you for a while. The other option is rebuilding the motor. Should you choose to rebuild the motor I recommend you get the Haynes or Chilton's repair manual on your vehicle for doing the job.

Aug 02, 2010 | 2000 Lincoln Navigator

3 Answers

99 deville head gasket leak?


A head gasket leak is usually indicated (among other things) by continous overheating of the motor, and subsequent loss of coolant.
It can also be indicated by the presence of engine combustion gas bubbles in the coolant resevoir.
Ensure the coolant system has no external leaks, such as faulty hose/s, radiator etc.

Ensure motor tune or other motor mechanical condition is not the cause of overheating.
I assume the motor is actually running hot.

Check cooling fans are operating ok (as necessary when car warms up):- if not check
1) fuse,
2) relay operation,
3) heat sensor switch.

Check/replace the thermostat,
Check the coolant pressure cap is serviceable & of correct rating,
Ensure cooling system is correctly filled, bleed off any airlocks as necessary when re-filling,
Ensure radiator hose on suction side of waterpump is not collapsing at engine revs above idle (due softening),
If the motor has been severely overheated, the head gasket could be blown - look for combustion gas bubbles in the coolant resevoir.

Sep 21, 2009 | 1999 Cadillac DeVille

3 Answers

Overheating when driving no mixing of the coolant and oil


The three most likely thing's cause overheating are faulty thermostat,electric fan or clogged radiator. Only at has been overheat so much it boils dry that it will cause engine trouble. Most common problem's are blown cylinder head gasket or a cracked cylinder head.
mixing coolant and water depends on where the gasket has blown or head is cracked. You will first need to check if it actually is overheating. The reason is. If the head is cracked or gasket blown then you can get a false boiling which is compresion from the cylinders blows through the crack in the head or gasket causing the coolant to blow out of the radiator cap.Fill the radiator to the top leave the cap off then start the engine.If the water blows out then you will need to remove the cylinder head check the gasket is ok. If its damaged replace if not get the head checked for crack's. If no water blow's when you start it check the thermostat is working properly. To check the thermostat put it a in a saucepan cover it with water bring the water to the boil. It should open before the water boil's but near boiling-point. If its ok then start the engine again leave it running until it boils and check the fan is running. If that's ok then its radiator problem. Their is no way to check if the radiator is ok you will need to get a new one. One last point. If the cylinder head or gasket are faulty it was caused by overheating so by just fixing the cylinder head problem is not a cure it will overheat again. Check the three things I mentioned at the begining and told you how to check them. Hope this help's. Cheer's

Aug 16, 2009 | 1992 Ford Explorer

2 Answers

Leaks


the only thing that causes this is a blown head gasket or a cracked block, the head gasket is the most common problem, the block being cracked rare/

Mar 19, 2009 | 1991 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...