Question about Mazda Cars & Trucks

Open Question

Tried to start truck 88 mazda b2200 seamed like I was not getting gas opened carb top didn't see gas going to carb any suggestions thank you

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: I have 1987 Mazda B2200 2.2 ltre, turns, fires, no fuel psi.

I had something like this before. There is a fuel saftey switch near the gas tank right by the rear end. Its a roll over sensor and mine fell off the mount and I guess the truck thought it was upside down :)

Posted on Jan 01, 2009

Ad
  • 150 Answers

SOURCE: Carb gas pouring out of hole on top front of carb

Sounds like the float has absorbed gasoline and can't ftoat anymore. This causes the fuel to not be shut off when float bowl is full causing the carb to flood. You will have to buy a carb kit and a float and rebuild the carb. Hope this helps.

Posted on Feb 15, 2009

rcampsr
  • 90 Answers

SOURCE: how to put on ignition switch on a '88 mazda b2200

If you mean actually replacing the ignition switch on the vehicle with a locking column. You need to do this. Dicconnect the battery, remove the lower panel of the dash if there is any. There is a bolt on the steering column near the fire wall on most vehicles, remove this bolt, it will release the spline on the steering column. Disconnect all wiring going to the column, unbolt the column from the dash support. Remove the column from the truck, on the ignition switch you will see where the two shear bolts screw the assembly together, center punch the center of each bolt. Now drill the bolt with a 1/8" drill about 1/4" to 3/8" deep. Now use a 3/8" drill and drill out the shear head until it comes off the bolt. You can now remove the switch assembly from the column. The new assembly should come with new shear off bolts so when you bolt it in place when tightned they will break off rendering it tamperproof again. Most vehicles are designed like this now to stop theft. Check the column for operation before reinstalling it in the reverse of above. You just want to make sure the key locks and unlocks the column before reinstalling in the vehicle. You may want to do this before you totally tighten the bolts and break them off permanently. Good luck, RAC

Posted on Apr 14, 2009

  • 8 Answers

SOURCE: timing instructions

the timming should be set @ 6BTC you will need a timming light to check it.
You should go buy a manual from your local automotive store befor changing your timming belt
the site below will show you how to make sure you timming marks are right but it will not explain the removel or installation
http://www.mazdatruckin.com/B2200//B2200_Timing_Belt.html

Posted on May 10, 2009

  • 6 Answers

SOURCE: can a bad ignition switch cause the truck to die

Yes, bad ignition switch can cause that, did on my B2200.

Posted on Dec 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

'88 Mazda 323 cranks, but won't start.


I wouldn't flood one cylinder and expect it to start. Try using a small amount of starting fluid in the air filter to confirm your plug wires are installed and working correctly.

Mar 26, 2014 | 1988 Mazda B2200

1 Answer

I have a 88 mazda b2200 it cranks up easy but if i do not push on gas pedal it will die...any suggestions?


Sounds like a carb problem, like the choke isn't functioning. Try some carb cleaner, and spray into the carb, and also check the air filter.
It could also be a vacuum leak. Check to make sure that all hoses and wires are connected properly.

Feb 07, 2012 | Mazda B2200 Cars & Trucks

1 Answer

When im driving about 45 or 50 mph my truck starts sputtering and slowing down. Its getting gas and the carburator is good what can it be. It an 87 mazda b2200


mcdevito75 here, It could be a dirty gas filter, weak fuel pump, fulty needle valve in the carb. Have your local shop check it out., Also could be a wek timeing chain.

May 12, 2010 | 1988 Mazda B2200

1 Answer

How do you change the starter out of a 88 mazda pickup B2200???


first things first make sure you unhook you battery then mark all the wires to your starter as you are removing them. remove the starte.then put its all back the way it was.

Apr 29, 2009 | 1988 Mazda B2200

1 Answer

Timing instructions


the timming should be set @ 6BTC you will need a timming light to check it.
You should go buy a manual from your local automotive store befor changing your timming belt
the site below will show you how to make sure you timming marks are right but it will not explain the removel or installation
http://www.mazdatruckin.com/B2200//B2200_Timing_Belt.html

Feb 25, 2009 | 1988 Mazda B2200

2 Answers

I have 1987 Mazda B2200 2.2 ltre, turns, fires, no fuel psi.


I had something like this before. There is a fuel saftey switch near the gas tank right by the rear end. Its a roll over sensor and mine fell off the mount and I guess the truck thought it was upside down :)

Dec 03, 2008 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...