Question about Mitsubishi L200

1 Answer

How do I remove gear stick on 2008 Mitsubishi l200

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 14,585 Answers

For the handle. Pull it back, on the front there will be a slot or set screw in the front. Set screw takes an allen wrench to loosen. Slot, insert a small flat screw driver and push in and pull up. To remove the shifter , you have to remove the console first. Screws and bolts could be(I do to many, I just know where to look). Panels under the dash, under cup holder mats, remove the box and lid, some under them. At the back, remove the blower vent or cover. and on the sides, you have to move the seats forward to get to them. then 4 bolts to remove and the wires and cables.

Posted on Dec 18, 2016

  • 2 more comments 
  • Leighton mckenzie
    Leighton mckenzie Dec 18, 2016

    Thank you, I have it stripped down and removed hi/low shifter, 3 bolts, for the main shifter no bolts or c clip or anything I can visibly see been at it all day it's a circle hole can move shifter up and down on Spring grrrrrrr

  • Randy Ohler Dec 18, 2016

    You have a manual transmission. I was talking automatic. With this I have seen 2 types. First there is a plate on top of the transmission with bolts to remove. Usually a plate to remove on the floor board. The other is a shear pin to push out. These are bit harder to remove at top. Use a dowel punch to get them out so far. Then takes pliers or vise grips to get them all the way out.

  • Leighton mckenzie
    Leighton mckenzie Dec 18, 2016

    Thank you again, must be the shear pin, where is it and roughly how big am I looking for? Sorry to sound like a flid

  • Leighton mckenzie
    Leighton mckenzie Dec 19, 2016

    Clutch all replaced, was 6 10ml bolts and whole assembly with both shifters came off. Thank you for all the help and advice

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 02 saturan l200 and the shift stick broke off from place where the gears are. I know it sounds confusing but I don't know the name of all the parts. Can anyone help me


Pull up on the shift lever boot to disengage from the console. The shift lever boot is rubber or leather or some other material !
Using a small screwdriver, remove the lever assembly retaining clip.
Remove the lever assembly ! I know this may sound complicated but it's real easy ! The shift leaver goes to a shift linkage that goes to the gear box !

Mar 06, 2015 | Cars & Trucks

1 Answer

Mitsubishi l200 warrior


first i would try changing the gearbox oil but it sounds like internal gearbox failure

Nov 26, 2013 | Cars & Trucks

1 Answer

Mitsubishi l200 warrior 2006 double cab. No indicators,fogs,main beam and headlights come on as soon as ignition is turned on? Please help. Thanks damion


sounds like the relay as its all the lights they sometimes stick find what one it is and remove it tap it alittle and replace if still no better replace it with a new one

Nov 10, 2013 | Cars & Trucks

1 Answer

My reverse lights aren't working on mitsubishi L200 why


You have the reverse switch on the gear box, thry to find it and see if it's ok, but before that first check ligtbubs, than fuse and than thry to finde the gearbox switch.

Feb 25, 2011 | 1997 Mitsubishi Eclipse

1 Answer

Where do I find engine and chassis numbers on a 2008 mitsubishi l200....


Hi,

The typical location of a Mitsubishi Identification plate, is usually found under the hood, riveted to the firewall (below the windscreen).

The plate will display all detail you require.





** If this has helped you in any way, please rate this solution **


Oct 29, 2009 | 2003 Mitsubishi Galant

1 Answer

1998 mitsubishi l200 jumpsout of 1st 3rd 5th


Sounds like a failed bearing or bad syncronizers. Will require trans disassembly to determine failure.

Feb 18, 2009 | 1988 Mitsubishi Pickup

1 Answer

05 mitsubishi l200 warrior changing up from 1st gear to 2nd allways snags but does not crunch


I have just got a mitsibushi L200 with no hand book .
Is there anyone who knows how to get it into two wheel drive,
I have tried but get the flashing 4 wheel drive simble still on the display and the sterring is heavy like its still in four wheeldrive.
HELP

Oct 06, 2008 | Mitsubishi Pickup Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...