Question about Cars & Trucks

1 Answer

When i put the drain plug bk on do i pop it in or twist it in first

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,585 Answers

If the seal is before the threads/lock. Push it in first then twist it to the locked position.

Posted on Dec 18, 2016


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Insignia estate boot will not open

If you can get into the boot by climbing through the car there is an emergency release mechanism fitted to the lock.
The flat, large trim panel on the tailgate should have a round plastic plug fitted. It will be near the bottom, centre of the panel. It will be lined up with the actual mechanical latch of the tailgate. Pop this plug out.
Using a large flat bladed screwdriver insert it into the hole and twist it. It should hook into a slot or groove. When this is twisted it should 'pop' the latch. Try twisting both directions as I'm not sure which is correct for that car.

Apr 02, 2018 | Cars & Trucks

2 Answers

What color is the alternator lite wire on 1976 f 100 with inline 6 cyl

It would be easier to pop your head under there and pull out the bulb and see what color the wire is that leads to the bulb.

Aug 06, 2017 | Cars & Trucks

1 Answer

How to Change Oil Using the EZ Oil Drain Valve?

Push in on the EZ drain and twist it to lock it open. After all the oil is drained out, twist it again until it pops back closed. Then replace your oil filter and refill your oil.

Oct 14, 2016 | Cars & Trucks

1 Answer

My 2 in honda wd 20x water pump had deisel fuel put in it now it wont run. Ive drained the tank and changed the plug on it. What can i do to get it bk running??

I'd guess you still have diesel in the fuel filter, and in the carburetor. Somehow you will need to get that diesel out of the system.

May 05, 2015 | Honda Cars & Trucks

1 Answer

How to flush coolant on 2004 grand prix

  • Move your badass w-body (a.k.a. Pontiac Grand Prix) to a level area and set the parking brake. Pop the hood and touch the radiator. If it's warm let it cool before you continue.
  • Twist the radiator cap one full turn (Remember to be careful because even when radiators are cool they can still erupt coolant)
  • Place any type of container (bucket [but has to be able to hold 2 gallons]) underneath the radiator and blow the drain plug. (The drain plug on your Grand Prix is on the driver's side bottom of the radiator facing the engine.)
  • Loosen the drain plug and let the old coolant to drain completely. (You may need a wrench to loosen the drain plug)
  • Dispose the old coolant in a sealable container (The coolant is very toxic to people and pets, so you gotta be careful)
  • Shut the radiator drain plug and fill the radiator with water.
  • Run car for a little bit and repeat the process again. (Let car cool, and drain water)
  • Close the drain plug and fill the radiator with fresh coolant until it's about an inch from overflowing. (DO NOT USE ORANGE DEX COOLANT IT IS HARMFUL FOR YOUR HEADGAKETS) You will need 3 gallons of coolant (SE, GT, GT1, GT2, GTP, GTP Comp G.) and 4 for the GXP model. Be sure to check the drain plug for any leakage.
  • Start your car and turn the heating system to high. Allow the car to keep running until the cooling fan turns on twice. After that happens, switch off the engine and check the coolant level. If it went down, add more coolant. If not, put the radiator cap back on and close the hood.

Feb 20, 2014 | Cars & Trucks

1 Answer

Radiator drain plug leaking

try fitting a flat rubber gasket on the plug before fitting. It is possible the there was one on it but it fell off unnoticed or was cracked and broke off.

Jan 14, 2013 | 2006 Pontiac Grand Prix

1 Answer

How do you change a parking light?

front: pop hood, look behind the lense for the assembly. twist and remove the assembly. twist bulb out of holder. put in new bulb. put back in, twist into place (opposite direction).
rear: pop trunk, may need to remove a panel to reveal the assembly. same directions.

Sep 18, 2010 | 2005 Mazda 6

1 Answer

How to drain antifreeze

you should have a drain plug at the bottom of your radiator. It will be a twist out plug, which will only unscrew so far to drain but if you pull on it, it will come out to drain faster. It will be some type of plug rather it be a twist type or takes an allen wrench or a basic wrench.

Sep 09, 2010 | 2000 Ford Taurus

1 Answer


remove single 7mm screw in wheelwell, pull out 2 plastic pop rivet type plugs also in wheelwell. pull back liner & twist to remove bulb. NOTE: install bulb THEN plug harness in. Small metal tab on light will not allow you to seat bulb correctly if harness is plugged in first, then twisted in!!!

Feb 09, 2010 | 2006 Chevrolet HHR

4 Answers

My 2002 Jeep Liberty 3.7 liter is leaking coolant from what appears to be the drain plug on the bottom of the radiator.I have to replace about 2 quarts of fluid after a short drive.And no one has drained...

The Drain Plug aka Radiator Drain **** has an o-ring on it that does wear-out over time, causing a leak. You can remove and replace these relatively ease. They only turn 1/4th to 1/3rd Counterclockwise to Open and Clockwise to Close. Work on only when the engine is cool. Leave the cap on the radiator to create a suction, decreasing the amount of radiator fluid you will lose. OR drain the Radiator Fluid into a clean container and save for reuse.
Have the new Radiator Drain **** ready for immediately insertion after removing the other leaking Radiator Drain ****. To Remove:
Twist the Radiator Drain **** counterclockwise and pull, continuing to twist counterclockwise removing it.
Immediately install the new Radiator Drain **** by first pushing in and then twisting clockwise to close.
Let me know if this helped, or if you have additional information or questions. Feel free to contact me at!

Jan 30, 2010 | 2002 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15314 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides