Question about Citroen C4

Open Question

Hi;my citroen c4 2006 model is showing an engen oil pressure information and it cuts off whiles in motion.It was diagnosed but the problem continues.Please help. From: Sam

Posted by on


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 131 Answers

SOURCE: oil pressure light comes on when I put the car in motion (at about 2000 rpms)

all turbo engines have a oil line to the turbo. If it is not getting oil the turbo will burn up and have to be replaced. Change your oil and filter to start with.

Posted on Jul 08, 2008

  • 532 Answers

SOURCE: sputtering while driving

try a tune up-plugs and wires-and air filter

Posted on Apr 23, 2009

  • 49071 Answers

SOURCE: Ford bantam rocam engen won't start after new olternator was put in .engen not cranking. Dashboard -battery and oil indicators come up but the car can't start.please help out

could be a bad battery/starter .

Posted on Aug 07, 2016

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Have red engene lights at panel

There several red lights that can come on showing a fault, park brake on, alternator not charging. no oil pressure, engine over heating, are just a few, check the drivers manual to find what each light relates to. Best not to drive till the faults are repaired.

Apr 03, 2016 | 2008 Nissan Qashqai 1.5

1 Answer

Why citroen c2 vtr burns main fuse number 7

Hi Mbuelelo
There is a short and the fuse is protecting the wiring from burning.

Substitute fuse for a circuit breaker and / or place ammeter or clamp ammeter in circuit to monitor current draw and avoid replacing many fuses while diagnosing problem.
Determine what devices that it powers and disconnect each till your meter current drops.

Sep 22, 2015 | Citroen Cars & Trucks

1 Answer

Hi I have a 96 mx6 that is leaking oil from a small rubber pipe at the bottom front of the engen. ehat pipe is this and what does it for?

it is a vent pipe for engine valve covers. oil leak would indicate pressure build up in the engine...I would replace the PCV valve.

Dec 31, 2014 | Cars & Trucks

1 Answer

Started with Oil Pressure dropping

DTC P0521: Engine Oil Pressure (EOP) Sensor Performance

The engine oil pressure (EOP) sensor changes voltage based on the engine oil pressure. The EOP sensor is a 3-wire sensor comprising of the signal circuit, the low reference circuit and the 5-volt reference circuit. The engine control module (ECM) supplies 5 volts to the EOP sensor via the 5-volt reference circuit and provides ground via the EOP low reference circuit. The ECM monitors the signal circuit of the EOP sensor to determine the EOP sensor voltage is within the normal operating range of approximately 1-4 volts. When the engine oil pressure is high, the EOP sensor voltage is high and the ECM senses a high signal voltage. When the engine oil pressure is low, the EOP sensor voltage is low and the ECM senses a low signal voltage. The ECM sends the EOP information to the instrument panel cluster (IPC) via GMLAN serial data message.

Conditions for Setting the DTC
The ECM detects that the difference between the predicted oil pressure and the actual oil pressure is either less than 47 kPa (6.8 psi) or greater than 50 kPa (7.3 psi).

Your best bet ,take it to a qualified repair shop that has the proper diagnostic testing equipment to diagnose this.

Nov 05, 2017 | 2008 GMC Yukon Xl 4WD

1 Answer

Hi guys, have citroen relay '08' plate 2.2 hdi. is the clutch hydrolic or cable? also struggling to get reverse gear, all others no problem at all. any ideas?

It is hydraulic. Are you engaging 2nd gear prior to reverse to slow gear motion and ease reverse effort? Is the engine idle speed with specs?

Sep 18, 2012 | Citroen Cars & Trucks

1 Answer

2004 tdi 4 motion dosnt start and says low oil preasure on the desh

If this is correct then your situation is more serious than you think. Think of it as your blood pressure, that's not good is it? Check your oil level with the orange dip stick. If your oil is at the top of knurled part of the stick it will tell you at least you have some oil in there, it should be lower once the pump is operating.
If it's way below the stick, this will tell you oil is below the level where the oil pump pick-up is at. The pump is not able to pick up oil from the oil pan and starving your engine which could end in a very expensive disaster.
If your level is fine and it does this, then you may have a
  1. Oil pump faulty
  2. Oil filter very dirty
  3. Oil filter faulty
  4. Loosing oil pressure due to internal system blocked or leaking externally or internally
The procedure for diagnosing oil pressure problem is using an analog oil pressure gauge connected to service ports from both the bottom and the top end of the engine. Without running the engine, a tool to turn the oil pump manually and pressurize the system while reading the gauge data.

Doing so will damage your internal moving parts and may seize the engine from oil starvation.

Apr 19, 2010 | 2003 Volkswagen Passat

1 Answer

The workshop did not fit the oil regulator and engene seized. but piston show that the problem was the injector, piston 2. Why have the engene broke after the oil filter has been changed, without the...

what oil regulators?? only change the oil filter and oil ,their is no regulator only a pressure relief valve but thats in the oil pump ,if the injector failed ,and allowed neat fuel into the piston then this would cause the piston to seize because it wash all the oil off the cylinder bore .then seize up time

Jul 24, 2009 | BMW 3 Series Cars & Trucks

1 Answer

1.8t gti cutting out

hi check the engines oil pressure this use to be a very common fault in golfs so it will proberly have a engine cut out when pressure gets low the pumps releif valve sticks plus how often do you change the oil if not regular it clogs the pumps filter yates210456

Oct 12, 2008 | 2000 Volkswagen GTI

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Citroen Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14403 Answers

Are you a Citroen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides