Question about Cars & Trucks

Open Question

I have a job backhoe 4x4 with sin to shift transmission.when I start it up it goes in gear and within minutes goes in neutral any ideas?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 416 Answers

SOURCE: Transmission shifting proublem M5R1 1997 FORD RANGER

You might have to try to adjust the freedom of clutch pedal,
The noise during shifting can be adressed to exessive wear clutch parts or again it might be a sign that indicates the not complete enabling the calutch
To find out what is causing the noise, set the parking brake, place the vehicle in neutral and start the engine.
If you hear growling or grinding noises when the clutch is engaged, the cause is the transmission input shaft bearing.
A squealing sound that occurs when the clutch pedal is depressed and held is usually caused by a bad pilot bearing or bushing.
A chirping noise that intensifies when the pedal is slowly depressed would indicate a bad release bearing.
If you hear chirping while idling in neutral and the noise goes away when the pedal is slowly depressed, the fork/pivot ball contact point is making the noise
Hope that helps.
The clutch adjustment procedure you can find at
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528018f021
More about clutches
http://www.aa1car.com/library/2002/ic100237.htm

Good Luck

Posted on Feb 27, 2009

smartr10U
  • 1305 Answers

SOURCE: 1999 F350 crew cab 4x4 ford, gear shift lever

Ok ready to stand on your head under the dash?
It's doable... there is a flange connected to the gearshift lever under the steering column. If you remove the lower dash cover where the fuses are, you should be able to see it when you move the gear shift lever... look around on the floor of the truck to see if you dropped a star-headed bolt or two... these bolts worked loose on my superduty and made shifting very difficult..it was an easy fix... let me know how you do on it.

Posted on May 10, 2009

jasperoni
  • 203 Answers

SOURCE: gear shift stuck in neutral when moving to park

1st check your shifter linkage-does the indication coincide with your gear recognition display in instrument cluster? most liley if it is not the linkage the gear recognition swith inside your shift box is defective-usually they get soda or coffee spelled on them and malfution. I would recomend having you car scanned for codes.

Posted on Jun 01, 2009

  • 295 Answers

SOURCE: 2001 Yukon XL SLT 4 speed Auto Transmission shift problem!

Sam,

I would start with a transmission fliud and filter service.

I would then have the trasnmission checked out by a transmission shop. The transmission most of the time has the direct drum band is starting to go. The shops can rebuild it no problem, This is a very common failure wiith the trasnmission.

Good Luck

Posted on Aug 16, 2009

Testimonial: "Thanks alot richtko94'! I'll try that!"

  • 1146 Answers

SOURCE: 92 chevy s10 4x4 4.3L manual transmission no 3rd gear

Hi:

Your transmission has 3 shift rails...
1st - 2nd
3rd -4th
5th- Reverse

If your 3rd gear doesn't work , you have an internal transmission problem, such as a syncronizer, or similar fail... There is not much you can fix, without removeing the transmission.

Posted on Nov 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a case 580k 4x4 backhoe is 4th gear set up different then 1st 2nd 3rd tractor won't move in lower gears made no noises or grinding .


Hi Bill:
I'd check with my local Case dealer. We have several pieces of Case equipment with hydostatic drives.
If I remember correctly, high gear on a standard transmission is a 1:1 ratio in that the power is on a straight through shaft.
My suspicion would be that a shifter link ay have become dis-connected.
Here's a link that may assist.
https://www.google.ca/webhp?sourceid=chrome-instant&ion=1&espv=2&ie=UTF-8#q=1987+case+backhoe+580k+4x4+transmission+diagram
Cheers

Apr 04, 2016 | Cars & Trucks

1 Answer

Transmission not shifting into high gear since abs/4x4 code


answer to any 4l60e trouble ' GMT400 - The Ultimate 88-98 GM Truck ...

www.gmt400.com > Street and Track > Transmissions
Mar 5, 2011 - Before guessing at transmission problems, check the fluid level (car warmed up, ... that do not show up as PCM codes (like shift A&B solenoid failures, for example). ... 1-2 shift is delayed and harsh, may not shift into OD: Check TPS for ...goes into 3rd gear: Reaction planetary is worn out due to high miles or ...

GMC Jimmy Transmission Problems - Edmunds

forums.edmunds.com > GMC > GMC Jimmy
Dec 20, 2013 - 1998 Jimmy After truck warms up shifts hard between 1st and 2nd gears. any ideas ... The ABS light stays on,the engine light stay on, the speedo doesn't work, .... I have a 1990 S15 4x4 Jimmy with a manual 5 speed transmission that went out. .... While driving it will only shift into 2nd gear and 3rd no overdrive. and usually ... Ford F-Series Transmission Problems - Edmunds
Dec 18, 2013
Buick Rendezvous Transmission and AWD Problems - Edmunds
Dec 18, 2013
Dodge Dakota Transmission Problems - Car Forums at Edmunds.com
Dec 18, 2013
Ford Transmission Problems - Edmunds
May 14, 1998
More results from forums.edmunds.com

Automatic Transmission May Not Shift Correctly at High ...

repairpal.com > Problems > Toyota > 4Runner

Feb 03, 2016 | Cars & Trucks

1 Answer

1998 blazer 4x4 cannot get it into 4 wheel high when i pus the button th4x4 and low range lights both blink and it goes back to 2 wheel high


Transfer Case Shift Control Switch Indicator Flashes and Returns to Original Mode.
Circuit Description
This symptom usually occurs when a shift into or out of 4LOW will not occur. When the transfer case control module (TCCM) receives a request to shift into or out of 4LOW, the TCCM must see the following parameters before the shift routine can start:
?€¢
The vehicle speed must be below 3 MPH.


?€¢
The transmission must be in neutral.

If the TCCM does not see these conditions the shift control switch indicator lamp will flash for approximately 5 seconds and then return to the original gear.
Test Description
The numbers below refer to the step numbers on the diagnostic table.

  1. This step tests the operation of the transfer case shift control switch to help determine if the system is operating properly.

  2. This step determines if the vehicle speed sensor reading is correct.

  3. This step determines if the park switch reading is correct.

Switch Indicator Lamp Flashes and Returns to Original Mode
Step

Action

Value(s)

Yes

No

Schematic Reference: Transfer Case Control Schematics

1

Important: The transfer case shift control module is not a class 2 device, and therefore a scan tool can not be utilized on this transfer case.

Did you perform A Diagnostic System Check?
--
Go to Step 2
Go to Diagnostic System Check

2

  1. Start the engine.
  2. Place the transmission into NEUTRAL.
  3. Set the park brake.
  4. Depress each of the shift control switch buttons.

Does the transfer case range change with the press of all of the shift control switch buttons?
--
Go to
Testing for Intermittent Conditions and Poor Connections
Go to Step 3

3

Use the scan tool in order to read the vehicle speed sensor on the transmission control Data Lists.

Is the vehicle speed within the specified range?
0 km/h (0 mph)
Go to Step 4
Go to
Powertrain On Board Diagnostic (OBD) System Check for the 4.3L engine

4

  1. Put the transmission in neutral.
  2. Observe the current state of the transmission on the scan tool in the transmission control Data 2 List.

Does the scan tool indicate the transmission is in Neutral?
--
Go to Step 5
Go to
Powertrain On Board Diagnostic (OBD) System Check for the 4.3L engine

5

Replace the transfer case shift control module. Refer to Transfer Case Shift Control Module Replacement .

Did you complete the replacement?
--
Go to Step 6
--

6

Operate the vehicle within the conditions for causing the symptom as specified in the supporting text.

Does the symptom re-occur?
--
Go to Step 2
System OK

Feb 12, 2015 | 1998 Chevrolet Blazer

1 Answer

I have a 1990 pathfinder 4x4 automatic trans. if you put it in drive it goes no slipping however wont shift to another gear unless u let your foot off the pedal and it jumps to 3rd gear. i manually put in...


Have you checked the transmission fluid level in park when the engine and transmission are warmed up? Is it full?
Does the fluid look red like it should or look dark brown and smell burned? If it looks and smells obviously burned, that is an indication of internal damage and it will need to be rebuilt.

Otherwise, there may be another problem with this specific transmission that I am unaware of.

Mar 15, 2014 | Nissan Cars & Trucks

2 Answers

Can a 1998 4x4 S-10 blazer be dinghy towed?


Yes it can, just place your Transfer Case in Neutral position.
Shifting into NEUTRAL
To shift the transfer case to NEUTRAL do the following:

Make sure the vehicle is parked so that it will not roll.
Set the parking brake.
Start the vehicle or turn the ignition to RUN.
Connect the vehicle to the towing vehicle.
Put the transmission in NEUTRAL (N).
Shift the transfer case to 2HI.
Simultaneously press and hold the 2HI and 4LO buttons for 10 seconds. The red NEUTRAL light will come on when the transfer case shift to NEUTRAL is complete.
Shift the transmission to REVERSE (R) for one second, then shift the transmission to DRIVE (D) for one second, or FIRST (1) for vehicles equipped with a manual transmission.
Turn the ignition to LOCK.
Place the transmission shift lever in PARK (P), or FIRST (1) for vehicles with a manual transmission.
Release the parking brake prior to towing.

Shifting Out of NEUTRAL
To shift out of NEUTRAL:

Set the parking brake and apply the regular brake pedal.
Shift the transmission to NEUTRAL (N) and turn the ignition to RUN with the engine off.
Press the button for the desired transfer case shift position (2HI, 4HI, AUTO 4WD or 4LO).
After the transfer case has shifted out of NEUTRAL the red light will go out.
Release the parking brake.
You may start the engine and shift the transmission to the desired position.
Excessively shifting the transfer case into or out of the different modes may cause the transfer case to enter the shift protection mode. This will protect the transfer case from possible damage and will only allow the transfer case to respond to one shift per 10 seconds. The transfer case may stay in this mode for up to three minutes.

NEUTRAL: Shift the vehicle's transfer case to NEUTRAL only when towing your vehicle.
Good luck and hope this answers your question.

Jan 30, 2010 | 1998 Chevrolet Blazer

3 Answers

I CAN NOT SHIFT THR TRANS INTO NUTRAL SO I CAN TOW IT BEHIND MY MOTOR HOME. IT WILL SHIFT INTO 2H, 4H, 4L


Shifting to NEUTRAL
To shift the transfer case to NEUTRAL, first make sure
the vehicle is parked so that it will not roll:
1. Set the parking brake.
2. Start the vehicle.
3. Connect the vehicle to the towing vehicle.
4. Put the transmission in NEUTRAL (N) or have
the clutch pedal pressed for vehicles with
manual transmission.
5. Shift the transfer case to 2HI.
6. Simultaneously press and hold the 2HI and
4LO buttons for 10 seconds. The red NEUTRAL
light will come on when the transfer case shift to
NEUTRAL is complete.
7. Shift the transmission to REVERSE (R) for one
second, then shift the transmission to DRIVE (D)
for one second or FIRST (1) for vehicles with
manual transmission.
8. Turn the ignition to OFF.
9. Place the transmission shift lever in PARK (P) or
FIRST (1) for vehicles with manual transmission.
10. Release the parking brake prior to towing.

************************

Shifting Out of NEUTRAL
To shift out of NEUTRAL:
1. Set the parking brake and apply the regular
brake pedal.
2. Start the vehicle with the transmission in PARK (P)
or FIRST (1) for vehicles with manual transmission.
3. Press the button for the desired transfer case position
(2HI, 4HI, AUTO 4WD or 4LO).
4. Put the transmission in NEUTRAL (N) or press the
clutch pedal for vehicles with manual transmission.
5. Shift the transmission lever to the desired position.
After the transfer case has shifted out of NEUTRAL,
the red light will go out.
6. A re-engagement sound is normal when shifting out
of NEUTRAL.

Jan 22, 2010 | 2000 GMC Jimmy

2 Answers

While shifting from 4x4 to 4x2 the gear lever is jammed at neutral position & jeep is not moving


there are no syncros in the transfer case, that would ease in shifting. i would try putting it in gear with the transmission, this will reposition the gears in the transfer case. then back to park or neutral. now try shifting to 4x2.

Jan 07, 2009 | 1988 Suzuki Samurai

1 Answer

Vehicle will not come out of N regardless of where the gear shift is moved to. Vehicle starts fine, but cannot be shift out of N.


I had a similar problem with a 1993 Dodge Dakota 4x4 club cab. With in the first year of ownership I had difficulty with the shifting from park to drive , the gear shift lever would not move or sometimes it would get stuck in neutral and I could not get it out. I took it into the local Chrysler/ Dodge dealer and they determined it was the park sprague. But after they replaced that part it continued to happpen. So, then after they contacted Chrysler Engineers they settled on replacing the back end of the transmission from a 1994 model year. That fixed the problem. They said the rod that goes from your gear shift lever into the transmission case did not line up properly with the stuff inside the transmission, therefore causing it to hang up. I am not sure if this is your same situation or not.

Jul 28, 2008 | 2008 Jeep Commander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...