Question about Cars & Trucks

Open Question

Rexton 290 4wd high and 4wd low light on when driving in 2wd

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: four wheel drive won't engage

Possible the front acutator is in operative. First check the wiring, since it runs under the axle tube, the check for power at the acutator plug in, if power there acuator faulty. If no power start with fuses. hope this is a starting point for you.

Posted on Jan 11, 2009

  • 3 Answers

SOURCE: truck changes from 2wd to 4wd high and 4wd low by

probably a bad 4wd switch have it checked I had sort of the same problem after dealer put factory fog lights in shorted out 4wd switch

Posted on Jan 04, 2010

  • 146 Answers

SOURCE: my 99 suburban 2500 is stuck in 4 wheel drive but

drive in reverse for 20 feet. if that doesn't work try disconnecting the battery neg first for a couple min hit your 2wd button.

Posted on Dec 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 ford ranger - Where is the 4x4 actuator located


On the transfer case
Transfer Case - Electronic Shift
The four-wheel drive electronic shift-on-the-fly feature electrically shifts the vehicle transfer case between 2WD, 4WD HIGH, and 4WD LOW. The system mode is selected by the operator through the mode select switch (MSS) on the instrument panel. The operator is informed which mode the system is in by two instrument cluster indicators: one for 4WD HIGH which appears as 4WD, and one for 4WD LOW, which appears as 4WD LOW. Shifts into 4WD HIGH can be made at any speed. When shifting into 4WD HIGH with the vehicle stationary, tooth blockage may occur preventing shift completion. When the vehicle is driven above 8 km/h (5 mph) the shift will complete. When shifting in or out of 4WD LOW, the four-wheel drive (4WD) control module requires that the vehicle speed be less than 5 km/h (3 mph), the brake pedal be applied, and the transmission be in NEUTRAL (automatic transmission) or the clutch pedal be depressed (manual transmission).
The gearmotor encoder assembly is mounted externally on the transfer case. It drives a rotary cam which moves the mode fork and range fork within the transfer case between the 4WD HIGH, 4WD LOW, and 2WD range positions.
The four-wheel drive (4WD) control module controls the gearmotor encoder assembly that shifts between 4WD HIGH, 4WD LOW, and 2WD modes.

Mar 17, 2017 | Ford Cars & Trucks

2 Answers

2008 Dodge Ram 4WD LOW light blinks while running in 2WD. When applied the 4WD High works fine as well as the 4WD LOW but the light keeps blinking and you can hear the system trying to apply 4WD LOW


Replace the motor/module on the transfercase. It has an internal short. Don't replace it. Soon you will have to replace or rebuild the transfer case and the motor.

Oct 31, 2014 | 2004 Dodge Ram 1500

1 Answer

How can I put the suburban into 4x4


I have a 1994 4x4 Suburban. In mine, there's a stick on the hump in the floor, and I'm sure this is the case with yours too. This year model does not require that you get out and lock your wheel hubs. There are labels that are supposed to light up to tell you if you're in 2wd, 4wdHigh, or 2wdLow, but mine don't seem to work. If it's dark out and I can't see the labels, I just have to remember that 4wd High is all the way towards me, 4wd Low is all the way forward, and 2wd in sort of in the middle (but closer to me than the actual middle).

To shift into 4wd High (which is what you'll use for most purposes, like driving in bad weather), just pull that stick back towards you in one swift motion. You can do this while you're parked or while driving forward down the highway.

To shift back out of 4wd High and into 2wd, just push that stick forward a little bit, to where it was before.

To shift into 4wd Low (which is what you'll use only for extreme conditions, like off-road mudding or getting out of your driveway in super deep snow), you have to be stopped. You can NOT just shift into 4wd Low while you're going down the road. First, put it into Neutral (with the shifter on the steering column), Then push that stick on the floor all the way forward. Mine is hard to push, so I use my foot.

To shift back into 2wd from 4wd Low, you need to be stopped and in Neutral also. Pull the stick back towards you to the same position it was in before. (Not all the way towards you, or you'll be in 4wd High instead of 2wd.)

Hope that helps.

Feb 15, 2014 | 1994 Chevrolet Suburban

1 Answer

Jeep stuck in 4wd High


For troubleshooting these issue,Few related help links are provided below.Click the link below and go through its troubleshooting procedure:----Jeep 4WD Idiot Light is ON? http://technoanswers.blogspot.in/2012/06/2002-jeep-wrangler-4wd-idiot-light-is.html
------------
Service 4wd warning light on Dash? http://howtobyme.blogspot.com/2011/11/service-4wd-warning-light-on-dash.html
---------------Car automatically switches to 4wd low? ------------Car will not go into 4WD high or 4WD low? http://schematicsdiagram.blogspot.com/2011/12/car-will-not-go-into-4wd-high-or-4wd.html
----------
No 4x4 light on dash?

http://repairhelpcenter.blogspot.com/2011/12/no-4x4-light-on-dash.html

---------------
4 wheel drive system will not disengage?

http://technoanswers.blogspot.com/2012/01/4-wheel-drive-system-will-not-disengage.html

------------
4WD light is flashing and beeping? NO 4WD high? http://schematicsdiagram.blogspot.in/2012/02/4wd-light-is-flashing-and-beeping-no.html
----------------This will help.Thanks.

Jul 17, 2012 | 1988 Jeep Cherokee

1 Answer

How do I turn 4wd on?


    • 1 Start your Dodge truck's engine.
    • 2 Turn the electronic transfer case from "2WD" to "4WD Lock" to engage the high range 4WD, if the dodge truck is equipped with an electronic transfer case; otherwise, shift the transfer case lever from "2H" to "4H." The electronic transfer case is located on the instrument panel and is marked with "2WD," "4WD Lock" and 4WD Low." The lever-equipped transfer case is located to the right of your leg and is marked with "2H," "4H" and "4L."
    • 3 Shift the transmission into "Neutral" while the vehicle is either stopped or rolling at 2 to 3 mph to begin engaging in the low range 4WD. Turn the electronic transfer case to "4WD Low," if the Dodge truck is equipped with an electronic transfer case; otherwise, shift the transfer case lever from "2H" or "4H" to "4L."
    Tips & Warnings
    • Indicator lights will come on and alert you that your vehicle is in either the high or low range of 4WD.
    • Do not engage in the low range of 4WD drive if the transmission is in gear; you must shift to "Neutral" first.
    • Many Dodge trucks allow you to shift from 2-wheel drive to the high range of 4WD at up to 55 mph--consult your truck's manual to ensure that this is possible. Do not exceed 55 mph while engaged in the high range of 4WD. Do not exceed 25 mph while engaged in the low range of 4WD.
    • Do not engage in 4WD unless you are on slipper or rocky roads.

Sep 02, 2011 | 2005 Dodge Dakota

1 Answer

How do I get it out of 4wheel into 2 wheel drive?


A 96 grand came with 3 different transfer cases in different models. if you see beside the 4x4 shifter there is the shift pattern printed there. some models only had the all-wheel drive option with high and low. others had 2wd-4wd high-n-4wd low. I would guess that since you're asking this, your jeep has only the all-wheel drive transfer case option. if this is the case... you are not able to run your jeep in 2wd

Jan 17, 2011 | 1996 Jeep Grand Cherokee

1 Answer

Truck changes from 2wd to 4wd high and 4wd low by


probably a bad 4wd switch have it checked I had sort of the same problem after dealer put factory fog lights in shorted out 4wd switch

Dec 19, 2009 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

4WD shift problems


Some one told me to unhook the batery for half an hour then hook it back up and try it. Well it worked,no more shif problems.

Nov 26, 2008 | 2000 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...