Question about Mazda Cars & Trucks

1 Answer

HOW TO REPLACE SERPENTINE BELTS ON A 1997 MAZDA 626 4 CYLINDER AND DO i HAVE TO REMOVE TIRE AND GO IN FROM WHEEL AREA?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 14,223 Answers

Here's a link Keith how how to change your belt. Repair Guides Routine Maintenance And Tune up Belts AutoZone com

Posted on Dec 17, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1997 Mazda 626 with a 4 cylinder replaced the radiator and when we when to start it all it would do is turn over kind of sluggish it's getting fire fuel in the ground wire is getting hot


Clean ground wire on where it connects to engine block and clean connections on battery. Make sure battery is charged. If battery is low, jump battery with another vehicle and see if it cranks at normal speed and starts.

May 25, 2015 | 1997 Mazda 626

1 Answer

Brake fluid leaking out of rear drum


replace rear wheel cyl , jack up car ,put axle stand under remove wheel knock of brake drun use mole grips and clamp of rear flevy pipe near rear axle then remove bad wheel cylinder clean every thing up very clean u will have to get a complet axle set of brake shoes also it would b safty first to also check other side they usaly go to geather i f u peel back the rubber on cylinger and there is brake fuiled ther replace it then bleed brakes if u are not go od at doing this get garrage or some one who is as brakes are dangerious if not done prof dont do ur self if not sure

Nov 06, 2013 | 1997 Mazda 626

1 Answer

How to remove the belts from crankshaft damper on nissan maxima 1996


If you have the older style V-Belts you have to lossen
a couple of the accy's--alternator,power steering pump,
air pump,etc

For a single serpentine belt- you just pull the tension of the
spring loaded belt tensioner

You may have to remove a plastic or rubber splash shield
as well as a tire & work thru the wheel well & over the sub frame

Jan 26, 2013 | 1997 Nissan Maxima

1 Answer

How to replace a water pump belt on a 2000 mazda 626


If its a 4cyl 2.0 remove your wheel and shield and using a jack and a bar and chain to hold up the motor from the top lay bar across from strut to strut and secure to engine, use a jack under the engine and add pressure to remove the motor mount on that side. loosen the alternator and power steering adjusters, remove belts starting with the Pwr steering then waterpump / alt install in reverse order .. do all of them while you are at it cause its a job.. First match the numbers on the belts with the new ones to make sure they are correct. Autozone always gets it wrong.then you could be stranded..

Feb 16, 2011 | 2000 Mazda 626

1 Answer

How long to replace clutch in a 1998 mazda 626


For a 4 cylinder 2.0L engine flag time to remove and replace clutch 5.4hrs.

For a 6 cylinder 2.5L engine flag time to remove and replace clutch
6.3 hrs.

hope this was helpful for you.

Sep 09, 2010 | 1995 Mazda 626

2 Answers

How do you remove wheel lock nuts without a key or bursting them on a 1994 mazda 626 diesel?


Gorilla lock makes special tools to remove these and are available online, or I would suggest just driving to a reputable tire shop in your area and have them remove the 4 lug locks ... I'm sure that they keep these tools handy and would only charge a nominal fee to remove your locks for you.

Dec 05, 2009 | 1994 Mazda 626

1 Answer

How to remove front tire


Hi Joker
First loosen up bolts that hold the tire on. Then you need to jack the car up using the jack from car or other type jack. Once the tire is off the ground you can remove the bolts and take off tire.

Hope this helps

Matt

Sep 18, 2009 | 1997 Mazda 626

1 Answer

How do you replace a serpentine belt on a mazda 626


A 626 has two belts. One drives the power steering and water pump (rear belt in 6 cyl) and other front belt drives the a/c and alternator. On the 4 cyl, the front belt drives the power steering and the a/c, and the rear belt drives the water pump and the alternator. All of these are easy to change.

Jul 04, 2009 | 2003 Mazda Protege

4 Answers

Cylinder order


The firing order on all four cylinder engines is 1.3.4.2. and number one cylinder is at the opposite end of the engine to the gearbox, at the end with the belts and pulleys.

Aug 20, 2008 | 1999 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...