Question about Ford Cars & Trucks

1 Answer

Diagram for heater blower wiring ford contour blower not working some wires look melted

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 3,371 Answers

I need model year to be sure I post the correct diagram? Probably a two wire connector at the blower motor, voltage and ground. Check voltage and ground, if your missing one or the other, track that circuit. If you have both good voltage and ground with no blower action, suspect the blower motor. I need more info.

Posted on Dec 17, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I get blower motor circuit diagram?


you don't need a diagram . you system is so simple you only have 3 things in it and one never fails.
you have a resistor that if it fails it never works again , so that's out
the motor can be failing and then work again .
but fords most common is a blower switch ,it melts .
so remove the switch and then remove the plug(if you can it might be melted to the switch) and look inside there to see if it's deformed , the plug might be deformed as well as the wires burnt.
start there first.

Feb 01, 2016 | 1996 Ford Contour

1 Answer

Where is my ign fuse located on my car


Below dash instrument panel, R16 ignition relay
98 Ford Contour SE Fuse Box Map
Fuse Panel Layout Diagram Parts: passenger side air bag, heater blower, interior lighting, heater blower motor, parking lamp, interior lighting, electric mirror, clock, wiper motor, ignition, reverse voltage protection, rear window defrost, engine management system, instrument panel illumination, radio, wiper motor, power windows, ABS module, backup lamp, brake lamp, door lock, main light, cigar lighter, electric seats,
link below should be the same as yours, press the helpful button

http://www.autofuseboxdiagram.com/1342-98-ford-contour-se-fuse-box-diagram

Jan 30, 2016 | 1999 Ford Contour

1 Answer

I have a Ford f150 and the heater does not work at all it will not blow nothing what could be the problem


Check blower motor fuse, if ok see if you can jump out the blower motor to see if it works. If it does check blower motor switch.
I had a ford contour the melted down the switch, some of ford wiring is underrated for the amperage.

Nov 29, 2015 | Ford Cars & Trucks

2 Answers

Have a 1998 ford contour...air wont blow out so I can use heater or air


Does the blower run at all when you select heat? Fuse #37 is the fuse for the heater blower - it should be a 30 amp fuse (this is in the fuse panel under the instrument panel.) There is also a heater Blower Relay in the Power Distribution Box in the engine compartment. It is #K14 (or maybe R14.)

Another thing to check is the resistor block for the blower motor. It is located on the bottom of the blower housing, on the passenger side, inside the car, below the instrument panel. You will see a wire harness with 3 or 4 wires going to a plastic connector. If the plastic looks like it's melted, it probably is, and that may be your problem. There will be a screw holding the resistor block in place in the housing. If you can remove the plastic connector, do so, the remove the screw and the resistor block. You can get replacement connectors with pigtail wires attached on the internet. (Google "1998 Contour Blower Motor Resistor Connector" Personally, I like the kit from Dorman carried by several different auto parts suppliers. It gives you a new resistor block along with the new connector.) Check the connection pins on the resistor block. If they are dirty or have melted plastic on them, they need to be cleaned. Use a small wire brush or sandpaper to make sure the blades are "bright metal" clean, then coat them with a good electrical protection-type grease. (The little packets of grease auto parts stores sell for car light bulb sockets work well, or a good dielectric silicone grease is fine.) Once you cut off the old melted connector, solder the new connector pigtails to the ends of the old harness wires and cover the joints with heat shrink tubing.. DO NOT use crimp connectors! You'll wind up with the same problem in a very short time! Put everything back together and see if it works.

I've attached a picture of the resistor block and the connector. I found this at O'Reilly Auto Parts web site:
http://www.oreillyauto.com/site/c/detail/DCH0/973415/02627.oap?year=1998&make=Ford&model=Contour&vi=1304019&ck=Search_02627_1304019_1100&pt=02627&ppt=C0331

If you're not comfortable doing this kind of work yourself, find a friend who is, or take it to a good shop (usually a dealer is not what I would call a "good shop".)

Good luck!

25362516-5uosy2mwawny0bti24cqjmzg-2-0.png

Jan 09, 2015 | 1998 Ford Contour

2 Answers

Heater fan isn't working in my 1997 ford f150 extended cab 4x4


What have you checked so far ?
Fuse - resistor - power at the blower motor ?

Feb 13, 2013 | 1997 Ford F150 Regular Cab

1 Answer

WHEN I TURN ON THE HEATER/AC BLOWER SWITCH NOTHING HAPPENS


The a/c blower is based upon the contour a/c system and the weakest link always was and still has been that blower motor resistor... It's white plastic on the passenger side under the dash, near the center right kick panel attached to the a/c case itself with 4 wires going to it with one bolt holding it in. My guess is the connector to it will have the wires melted back a bit or the connector won't come off of the resistor itself.

Fix is usually replace the resistor and install a connector kit from Ford that was used in a recall for Contours that used a heavier gauge wire at the end near the resistor itself.

I don't have the numbers handy, but a Ford parts department guy whos been there a while will probably know what I'm talking about .

The switches were known to burn on some models also where it would melt the connector and switch... Usually I replace the switch and connector also in a pair with the resistor due to my dislike of Ford of Europe's idea of undersizing critical wires.

If the resistor ain't burnt, you may want to pull and see if the connector on the switch ain't burnt.

Dec 28, 2010 | 1999 Mercury Cougar

2 Answers

98 ford contour wiring diagram


When you tell us "wiring diagram", is for one specific circuit or you are refer to the firing order?

Apr 13, 2010 | 1998 Ford Contour

1 Answer

Heater of my 1999 ford contour is not working. is there a fuse i can replace to make it work?


There is a fuse under the steering wheel area, also there is a heater conrol under the passenger side dash on the left side of the blower motor. 1 screw holds it in the plenum(heating duct) there is a 4 wire plug going to it. You can check the actual blower motor for operation by putting 12 volts to it. To remove it there are two tabs on either side of the housing.Remove the wire first. Push the tabs up together and turn the fan housing to remove it. You now will have the whole fan in your hands. Using a wire jump from a 12v source(car battery works) to test the fan.2 wires reqd for + and-. if the fan does not function it may need replacing or just lubrication.

Jan 09, 2010 | 1999 Ford Contour

1 Answer

1999 contour heater blower doesn't work i


on blowermotor ground ground wire to a go metal ground and see if motor runs if it does then you have a bad ground. also try tapping on motor if it turns on then replace motor,hope this helps.

Oct 19, 2009 | 1999 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...