Question about 2006 Ford Freestyle

1 Answer

When is the transmission intake valve on a 2006 freestyle V6 engine

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Ford Master
  • 14,587 Answers

Transmission intake valve ? No such thing !

Posted on Dec 17, 2016


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 474 Answers

SOURCE: how to locate a intake air temperature sensor on

That sensor is built into the mas air flow sensor

Posted on Feb 05, 2010

  • 186 Answers

SOURCE: My car when I drive it feels like there is an

I would check your tires for a seperation, and then diagnose your check engine light to see what trouble code its storing. Hope this helps.

Posted on Mar 02, 2010

  • 2926 Answers

SOURCE: How do you get to,

VTC selonoid was on the back of the cylnder head right by the PCV valve. The VTC solenoid valve is part of the Valve Timing Control System. The purpose of the system is to achieve optimum valve timing, thus improving engine performance.

The system will vary the intake valve timing according to engine speed, and other inputs received from the coolant temperature and throttle position sensors. The ECM controls the position of the intake camshaft, by controlling the oil pressure to the intake camshaft pulley hub. When the ECM energizes the solenoid, oil pressure is supplied to the pulley hub, changing the position of the hub, thereby advancing the intake valve timing.

1 Remove the VTC valve from the vehicle.

2 Using a fused jumper wire, apply battery voltage to terminal 1, and ground to terminal 2.

3 If the valve is functioning correctly, the plunger shaft in the valve should be extended.

4 If the plunger is not extended, replace the VTC solenoid.


1 Disconnect the wiring harness connector from the VTC valve.

2 Using a suitable wrench, remove the VTC from the cylinder head.

To install:

1 Install the VTC in to the cylinder head, by first hand tightening, then using a wrench.

2 Plug the wire harness connector into the VTC valve

Posted on Jun 24, 2010

  • 27 Answers

SOURCE: What/When is the recommended maintenace

Every 30,000 miles

Posted on Sep 24, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


P0174: Fuel Injection System Too Lean Bank 2

P0171: Fuel Injection System Too Lean Bank 1

P0401: Exhaust Gas Recirculation Flow Insufficient Detected

P0457: EVAP Control System Leak Detected Fuel Filler Cap Loose/Off P0457 Ford EVAP Control System Leak Detected Fuel Filler Cap Loose Off

P2104: Throttle Actuator Control System Forced Idle

P0111: Intake Air Temperature Sensor 1 Circuit Range/Performance Problem

P0112: Intake Air Temperature Sensor Circuit Low Input

P0218: Transmission Fluid Temperature Over Temperature Condition

Dec 07, 2016 | 2006 Ford Freestyle

1 Answer

My 2006 Ford freestyle starts alright, but it does not move when I select a gear. The engine idles smoothly.

Ford knows there is a problem with the 2006 Freestyle CVT transmission but won't do anything about it because there weren't enough cars with the problem to recall. You will probably need to replace your transmission..

Jul 21, 2014 | Cars & Trucks

1 Answer

Can you bolt a 2006 3.6 v6 to the transmission of a 2003 which has a 3.4 v6?

I'm not certain if it would physically bolt in, but it would be a nightmare to get the electronics working properly. I found that the 3.4L isn't a bad engine, aside from intake gasket leaks. There is an updated intake gasket set available that seems to be working great.

Feb 02, 2013 | Buick Rendezvous Cars & Trucks

1 Answer

Nissan altama 2005 3.5 l v6 problems are running smooth when engine is cold 5-10 min there us a problem with engine vibrations on the stop i get the trouble code which is po0011

Here is the definition. You may want to do some research on the code and the valve that controls cam timing.

P0011 NISSAN Description This valve mechanism hydraulically controls cam phases continuously with the fixed operating angle of the intake valve.

The ECM receives signals such as crankshaft position, camshaft position, engine speed, and engine coolant temperature. Then, the ECM sends ON/OFF pulse duty signals to the intake valve timing control solenoid valve depending on driving status. This makes it possible to control the shut/open timing of the intake valve to increase engine torque in low/mid speed range and output in high-speed range.

The intake valve timing control solenoid valve changes the oil amount and direction of flow through intake valve timing control unit or stops oil flow. The longer pulse width advances valve angle. The shorter pulse width retards valve angle. When ON and OFF pulse widths become equal, the solenoid valve stops oil pressure flow to fix the intake valve angle at the control position.
Read more:

Sep 12, 2012 | 2006 Nissan Xterra

2 Answers

Were is the pcv valve located on my 2000 ford explorer ? even the auto patrs store people can'y find it.

Hi there!

The PCV valve is located at the back of the intake manifold if your engine is 5.0L V8. and if you have a 4.0L v6 engine i would say its one the valve cover by the Brake booster. Good luck

Jun 26, 2011 | Ford Explorer Cars & Trucks

2 Answers

I have a 2006 Ford Freestyle with 70K miles. My

No solution. Just got the EXACT same issue last weekend. myfordfreestyle notes said to remove air intake and clean throttle body with basic tb cleaner. seemed to help, but getting some more engine reving during routine shift into park situations.

Any ideas out there? =H

May 14, 2010 | 2006 Ford Freestyle

1 Answer

06 ford freestyle can't find the oil plug

Usually on the right side of the engine oil pan. Not the transmission. It is always on the side where it can't get knocked off by railroad tracks or other road hazards. Hope this helps.

Apr 12, 2010 | 2006 Ford Freestyle

1 Answer

My car when I drive it feels like there is an earthquake in my front seat. My check engine light is also on. Its a 2006 Ford Freestyle V6 with approx 61,000 miles on it.

I would check your tires for a seperation, and then diagnose your check engine light to see what trouble code its storing. Hope this helps.

Mar 02, 2010 | 2006 Ford Freestyle

Not finding what you are looking for?
2006 Ford Freestyle Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides