Question about Mazda Cars & Trucks

Open Question

Hi I'm driving mazda etude ie model 2000,its not starting,I bored coils,crank sensor,but stil not starting,what can be the problem?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
thutson66
  • 96 Answers

SOURCE: 2001 mazda protege will not start

well, with all that you have changed the only two possible things that are left PCM and the ECM....

Do you have an alarm system on this vehicle? If you purchased this car second hand it may have something that is inhibiting the engine from firing. From what you have told us here that would be where I would start looking.

I really hope this is helpfull

Posted on Aug 10, 2008

Ad
dpjones1700
  • 26 Answers

SOURCE: timing belt setting and my car iddle are out of form mazda etude

Your camshaft and crankshaft pulleys have to be properly aligned upon installation of the timing belt. The cogs on the belt, should fit precisely with the teeth of the pulleys. Your # 1 engine cylinder should be moved to "Top Dead Center" before installing the belt. This means no compression once the top of the piston cylinder reaches the top of the chamber.

Posted on Nov 27, 2008

  • 2 Answers

SOURCE: hi there i'm driving a mazda etude 1.6i 2000 model

Hi my mazda etude 160i the left wheel gets stuck and it give a knocking sound.then its free again.I checked the CV but thats fine.

Posted on Mar 29, 2010

  • 1 Answer

SOURCE: Mazda Etude 160ie timing

I have a problem with the mazda etude 160ise, the crank shaft sensor was damages and replaced it ad now the car cant tart. Note that the timing was afected in that the two sealings were replaced. Could one please provide information as to how I can get in timing and get it going again.

Posted on Nov 27, 2010

  • 17 Answers

SOURCE: mazda etude 1.6 i cut out while driving starting after about 10 min.

sounds like the coil pack is braking down when hot. check for spark while engine wont start

Posted on Jan 27, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have a Mazda etude 1.6 ie I replaced the timing belt and nu it don't wane pick up any revs the timing is correctly set the.valve is ok.it idles well on 2000 revs but when i pres the gas it dies


not a Mazda man but 2000 rpm's at idle is more than double what it should be . My toyota idles at about 750 .runs 2000 going 70 mph down the highway

Jul 30, 2015 | Mazda Cars & Trucks

1 Answer

My mazda etude 160ie have no spark


Test coil, ignition module, crank/cam sensors, ignition fuses, relays. ECU must get inputs from several places to allow spark.

Jun 11, 2015 | Mazda Cars & Trucks

1 Answer

Hi there my mazda etude 160i wont start at normal operating temp must leave for few minutes then will start again


When you shut off a fully warmed up engine, the temp rises as all water circulation has stopped. This extra high temp can cause electronic parts to fail which then work again as they cool. Somewhat rare, but possible coil/module or crank/cam sensor issue. Also may have leaky injectors which bleed down when you stop and flood the engine. Sitting lets excess fuel evap and then will start again. Just my thoughts.

Feb 23, 2015 | Mazda Cars & Trucks

1 Answer

Mazda 323 Hatchback 1.8 DOHC 2000 model car


need to check the crank sensor and coil pack

Oct 06, 2009 | 2000 Mazda B-Series

2 Answers

Mazda Etude 160ie timing


I have a problem with the mazda etude 160ise, the crank shaft sensor was damages and replaced it ad now the car cant tart. Note that the timing was afected in that the two sealings were replaced. Could one please provide information as to how I can get in timing and get it going again.

Jan 02, 2009 | 2004 Mazda 3

3 Answers

MAzda etude 323 Familia cuts out


the crank shaft sensor is bad, it is heating up, and that is why it works after the water being poured on it, it is cooling it off.....

Nov 19, 2008 | 2003 Mazda MPV

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...